Biodom
Legendary
Offline
Activity: 3864
Merit: 4269
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:20:28 PM |
|
![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2FCJwSJFV.png%3F1&t=665&c=A0IQtrS4eArKmw) I got mine to freq 250. Took out the intake fan and used a fan I had laying around. ![](https://ip.bitcointalk.org/?u=https%3A%2F%2Fi.imgur.com%2Fq7G460A.jpg&t=665&c=9j1e1FoetjkT1A) . I replaced the thermal paste for all the chips and only had enough left over for one of the heat sink in the back. You can see the temp difference of replacing the thermal paste. I used Antec F7 since I didn't want to wait for the MX-4 to arrive in the mail. The room is about 23.3C and the fan rarely goes above 1700. interesting, but why taking out the intake fan?
|
|
|
|
boyohi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:26:55 PM |
|
I got mine to freq 250. Took out the intake fan and used a fan I had laying around. I replaced the thermal paste for all the chips and only had enough left over for one of the heat sink in the back. You can see the temp difference of replacing the thermal paste. I used Antec F7 since I didn't want to wait for the MX-4 to arrive in the mail. The room is about 23.3C and the fan rarely goes above 1700.
interesting, but why taking out the intake fan? I experimented with the intake fan on and off. It seemed a little redundant to have a fan blowing into the intake. Once I took off the intake and the piece of metal behind it I saw a ~2C drop in temp. Edit: I also took the case off.
|
|
|
|
MoreBloodWine
Legendary
Offline
Activity: 1050
Merit: 1001
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:32:40 PM |
|
Well, as I start this reply it's 1:23pm.
I just OC'd all four of my S3's to 237.5, I have a dentist appointment at three. So after I hit the post button. I'm gonna do a single refresh on all four to see web stats. After that I'll let everything be til probably around 4pm when I get back. If everything looks good, I'll leave them all on 237.5 for 24hrs.
If after that, everything still looks good. Then about this time tomorrow or so I will take the proverbial plunge and try 250 on one of them for 24hrs. If that holds good, then I'll set the second at 250 and let run 24hrs, so on and so forth til I t all four on 250 if I'm lucky.
Between 237.5 & 250, is there any other freqs, I think I saw someone say 240 or something a few pages back.
Ok, so back from the dentist, checked on the four S3's and no x's but I did however notice something weird and maybe it will wind up between now and tomorrow. Anyway, below are as of this post... Elapsed Time, Gh/s(5s) & Gh/s(avg) as well as the HW & the Diff a & r figures. My curiosity is in tthe avg speed of miners 1 & 3 while 2 & 4 look good. Haven't done the HW% math, maybe someone could for me ? lol. Oh ya, all four are OC'd to 237.5 Miner 1Time: 2h 23m 11s 5s: 451.62 Av.: 445.94 HW: 269 Diff A: 867,072 Diff R: 2,560 Miner 2Time: 3h 6m 23s 5s: 471.79 Av.: 474.91 HW: 927 Diff A: 1,222,656 Diff R: 4,096 Miner 3Time: 2h 56m 37s 5s: 468.71 Avg.: 458.37 HW: 86 Diff A: 1,109,504 Diff R: 1,536 Miner 4Time: 3h 6m 6s 5s: 501.62 Avg.: 475.88 HW: 54 Diff A: 1,244,160 Diff R: 1,536 About this time tomorrow I'll use actual pics when it will be ~24hrs that they will all have been up on 237.5.
|
To be decided...
|
|
|
Biodom
Legendary
Offline
Activity: 3864
Merit: 4269
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:34:01 PM |
|
I got mine to freq 250. Took out the intake fan and used a fan I had laying around. I replaced the thermal paste for all the chips and only had enough left over for one of the heat sink in the back. You can see the temp difference of replacing the thermal paste. I used Antec F7 since I didn't want to wait for the MX-4 to arrive in the mail. The room is about 23.3C and the fan rarely goes above 1700.
interesting, but why taking out the intake fan? I experimented with the intake fan on and off. It seemed a little redundant to have a fan blowing into the intake. Once I took off the intake and the piece of metal behind it I saw a ~2C drop in temp. Edit: I also took the case off. Oh, so you basically made it S1-like. S1 was known to respond well to an external fan blowing air in the same direction-I used it all the time, but it had zero effect on closed S3, as you would expect.
|
|
|
|
boyohi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:36:35 PM |
|
Well, as I start this reply it's 1:23pm.
I just OC'd all four of my S3's to 237.5, I have a dentist appointment at three. So after I hit the post button. I'm gonna do a single refresh on all four to see web stats. After that I'll let everything be til probably around 4pm when I get back. If everything looks good, I'll leave them all on 237.5 for 24hrs.
If after that, everything still looks good. Then about this time tomorrow or so I will take the proverbial plunge and try 250 on one of them for 24hrs. If that holds good, then I'll set the second at 250 and let run 24hrs, so on and so forth til I t all four on 250 if I'm lucky.
Between 237.5 & 250, is there any other freqs, I think I saw someone say 240 or something a few pages back.
Ok, so back from the dentist, checked on the four S3's and no x's but I did however notice something weird and maybe it will wind up between now and tomorrow. Anyway, below are as of this post... Elapsed Time, Gh/s(5s) & Gh/s(avg) as well as the HW & the Diff a & r figures. My curiosity is in tthe avg speed of miners 1 & 3 while 2 & 4 look good. Haven't done the HW% math, maybe someone could for me ? lol. Oh ya, all four are OC'd to 237.5 About this time tomorrow I'll use actual pics when it will be ~24hrs that they will all have been up on 237.5. https://bitcointalk.org/index.php?topic=596178.0Try Ant Monitor. Its pretty useful. It will tell you your HW% and you can set up alerts. Use the S1 settings when setting up.
|
|
|
|
boyohi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:39:05 PM |
|
I got mine to freq 250. Took out the intake fan and used a fan I had laying around. I replaced the thermal paste for all the chips and only had enough left over for one of the heat sink in the back. You can see the temp difference of replacing the thermal paste. I used Antec F7 since I didn't want to wait for the MX-4 to arrive in the mail. The room is about 23.3C and the fan rarely goes above 1700.
interesting, but why taking out the intake fan? I experimented with the intake fan on and off. It seemed a little redundant to have a fan blowing into the intake. Once I took off the intake and the piece of metal behind it I saw a ~2C drop in temp. Edit: I also took the case off. Oh, so you basically made it S1-like. S1 was known to respond well to an external fan blowing air in the same direction-I used it all the time, but it had zero effect on closed S3, as you would expect. Yeah. I also took the internal wireless antenna from my old laptop and made it wireless. Its in my room so I needed to make the fan less noisy and ended up with this.
|
|
|
|
MoreBloodWine
Legendary
Offline
Activity: 1050
Merit: 1001
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:45:56 PM |
|
Well, as I start this reply it's 1:23pm.
I just OC'd all four of my S3's to 237.5, I have a dentist appointment at three. So after I hit the post button. I'm gonna do a single refresh on all four to see web stats. After that I'll let everything be til probably around 4pm when I get back. If everything looks good, I'll leave them all on 237.5 for 24hrs.
If after that, everything still looks good. Then about this time tomorrow or so I will take the proverbial plunge and try 250 on one of them for 24hrs. If that holds good, then I'll set the second at 250 and let run 24hrs, so on and so forth til I t all four on 250 if I'm lucky.
Between 237.5 & 250, is there any other freqs, I think I saw someone say 240 or something a few pages back.
Ok, so back from the dentist, checked on the four S3's and no x's but I did however notice something weird and maybe it will wind up between now and tomorrow. Anyway, below are as of this post... Elapsed Time, Gh/s(5s) & Gh/s(avg) as well as the HW & the Diff a & r figures. My curiosity is in tthe avg speed of miners 1 & 3 while 2 & 4 look good. Haven't done the HW% math, maybe someone could for me ? lol. Oh ya, all four are OC'd to 237.5 About this time tomorrow I'll use actual pics when it will be ~24hrs that they will all have been up on 237.5. https://bitcointalk.org/index.php?topic=596178.0Try Ant Monitor. Its pretty useful. It will tell you your HW% and you can set up alerts. Use the S1 settings when setting up. Can't until M patches it for hosted outside the home network machines.
|
To be decided...
|
|
|
boyohi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 08:49:54 PM |
|
Well, as I start this reply it's 1:23pm.
I just OC'd all four of my S3's to 237.5, I have a dentist appointment at three. So after I hit the post button. I'm gonna do a single refresh on all four to see web stats. After that I'll let everything be til probably around 4pm when I get back. If everything looks good, I'll leave them all on 237.5 for 24hrs.
If after that, everything still looks good. Then about this time tomorrow or so I will take the proverbial plunge and try 250 on one of them for 24hrs. If that holds good, then I'll set the second at 250 and let run 24hrs, so on and so forth til I t all four on 250 if I'm lucky.
Between 237.5 & 250, is there any other freqs, I think I saw someone say 240 or something a few pages back.
Ok, so back from the dentist, checked on the four S3's and no x's but I did however notice something weird and maybe it will wind up between now and tomorrow. Anyway, below are as of this post... Elapsed Time, Gh/s(5s) & Gh/s(avg) as well as the HW & the Diff a & r figures. My curiosity is in tthe avg speed of miners 1 & 3 while 2 & 4 look good. Haven't done the HW% math, maybe someone could for me ? lol. Oh ya, all four are OC'd to 237.5 About this time tomorrow I'll use actual pics when it will be ~24hrs that they will all have been up on 237.5. https://bitcointalk.org/index.php?topic=596178.0Try Ant Monitor. Its pretty useful. It will tell you your HW% and you can set up alerts. Use the S1 settings when setting up. Can't until M patches it for hosted outside the home network machines. I made mine wireless and I connect through the router. I can jump on any computer in the house and monitor it. Edit: https://bitcointalk.org/index.php?topic=702653.msg8062114#msg8062114After you connect it just treat it like an S1 and you can set up the wireless. Once you connect to the wifi it will be named WWAN by default. Go to WAN and change it to DHCP client and save and apply it. Disconnect the wire and turn the power off and on. I reserved the DHCP on my router for the Antminer's MAC address so it will always have that IP.
|
|
|
|
MoreBloodWine
Legendary
Offline
Activity: 1050
Merit: 1001
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:18:06 PM |
|
Well, as I start this reply it's 1:23pm.
I just OC'd all four of my S3's to 237.5, I have a dentist appointment at three. So after I hit the post button. I'm gonna do a single refresh on all four to see web stats. After that I'll let everything be til probably around 4pm when I get back. If everything looks good, I'll leave them all on 237.5 for 24hrs.
If after that, everything still looks good. Then about this time tomorrow or so I will take the proverbial plunge and try 250 on one of them for 24hrs. If that holds good, then I'll set the second at 250 and let run 24hrs, so on and so forth til I t all four on 250 if I'm lucky.
Between 237.5 & 250, is there any other freqs, I think I saw someone say 240 or something a few pages back.
Ok, so back from the dentist, checked on the four S3's and no x's but I did however notice something weird and maybe it will wind up between now and tomorrow. Anyway, below are as of this post... Elapsed Time, Gh/s(5s) & Gh/s(avg) as well as the HW & the Diff a & r figures. My curiosity is in tthe avg speed of miners 1 & 3 while 2 & 4 look good. Haven't done the HW% math, maybe someone could for me ? lol. Oh ya, all four are OC'd to 237.5 About this time tomorrow I'll use actual pics when it will be ~24hrs that they will all have been up on 237.5. https://bitcointalk.org/index.php?topic=596178.0Try Ant Monitor. Its pretty useful. It will tell you your HW% and you can set up alerts. Use the S1 settings when setting up. Can't until M patches it for hosted outside the home network machines. I made mine wireless and I connect through the router. I can jump on any computer in the house and monitor it. Edit: https://bitcointalk.org/index.php?topic=702653.msg8062114#msg8062114After you connect it just treat it like an S1 and you can set up the wireless. Once you connect to the wifi it will be named WWAN by default. Go to WAN and change it to DHCP client and save and apply it. Disconnect the wire and turn the power off and on. I reserved the DHCP on my router for the Antminer's MAC address so it will always have that IP. Sorry but there's no wireless antenna I can put on my machines 5hrs away from me.
|
To be decided...
|
|
|
montyfd
Member
![*](https://bitcointalk.org/Themes/custom1/images/star.gif)
Offline
Activity: 60
Merit: 10
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:18:11 PM |
|
Is anybody using the Antmonitor software together with the new firmware? After updating the firmware, the monitor does not display any values for this S3. In the webinterface and pool all is ok.
|
|
|
|
dlasher
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:37:00 PM Last edit: August 14, 2014, 10:27:15 PM by dlasher |
|
Think I had my first S3 die, want to confirm. Got idle miner notification, was able to connect to box, cgminer would start when crash - restarted box - no change
- power-cycled box - no change
- noticed the web interface kept throwing "file not found" errors
- thought maybe file system corruption, replaced cgminer binary from good miner -- no change
- figured i'd try a code upgrade -- no change
- swapped PSU -- no change
when I start cgminer from the CLI, it will run for a while, but at about 100-110GH.. none of the ASIC show disabled. decided to power cycle it again, and now it won't come back up.. it's on, but the RED LED just flashes ON..wait.. OFF.. wait.. ON... wait.. forever. is it dead? Suggestions for recovery? Took a quick video, two booted at the same time.. at around 32 seconds you can see the right one take off, left one never does. https://vid.me/Hq1
|
|
|
|
h3rlihy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:46:00 PM |
|
Could anybody give me any suggestions as to why my antminer seems to be running kinda shit? ![](https://ip.bitcointalk.org/?u=http%3A%2F%2Fi57.tinypic.com%2Fnx01mh.jpg&t=665&c=cJeT80nkm5Re-Q) Seems to want to only hold 400 gh/s comfortably. Those spikes at the end are the results of reboots. Whenever I reboot it, it runs nicely for a bit, then deteriorates back down to 400. Never seems to be able to hold the 440gh/s as expected. I have it running off a Corsair 750W PSU with all four PCI-E cables connected so power shouldn't be an issue. It is also running completely stock, I tried overclocking to 'compensate' for this shortfall but even slight overclocks produced great instability and knocked out one of the chips. I've looked about and this seems kinda like a rare issue but my ant just doesn't want to play ball.
|
|
|
|
boyohi
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:52:01 PM |
|
Could anybody give me any suggestions as to why my antminer seems to be running kinda shit?
Seems to want to only hold 400 gh/s comfortably. Those spikes at the end are the results of reboots. Whenever I reboot it, it runs nicely for a bit, then deteriorates back down to 400. Never seems to be able to hold the 440gh/s as expected.
I have it running off a Corsair 750W PSU with all four PCI-E cables connected so power shouldn't be an issue. It is also running completely stock, I tried overclocking to 'compensate' for this shortfall but even slight overclocks produced great instability and knocked out one of the chips.
I've looked about and this seems kinda like a rare issue but my ant just doesn't want to play ball.
Did you try opening it and replacing the thermal paste? Some of the units ship with horrible thermal paste. It could also be a heat issue. I'm not an expert on the issue.
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4228
Merit: 8451
'The right to privacy matters'
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:53:46 PM |
|
I got a pair of them in today.
I have 3 running on my evga 1300
they are doing
the old batch 4
231.25 231.25
the new batch 6
237.50 - 479gh low hw
and one is on a seasonic platinum 760 watt.
it is doing
218.75 437gh very low hw
|
|
|
|
h3rlihy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 09:56:17 PM |
|
Did you try opening it and replacing the thermal paste? Some of the units ship with horrible thermal paste. It could also be a heat issue. I'm not an expert on the issue.
I watch the "miner status" page like a hawk and have not once seen it hit any higher than 43 - 45. I only rarely hear the fans really get going.
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4228
Merit: 8451
'The right to privacy matters'
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 10:01:47 PM |
|
the 3 on the evga are doing 1120 watts and about 1300gh
nice numbers.
|
|
|
|
GigaWave
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 10:21:15 PM |
|
Well, as I start this reply it's 1:23pm.
I just OC'd all four of my S3's to 237.5, I have a dentist appointment at three. So after I hit the post button. I'm gonna do a single refresh on all four to see web stats. After that I'll let everything be til probably around 4pm when I get back. If everything looks good, I'll leave them all on 237.5 for 24hrs.
If after that, everything still looks good. Then about this time tomorrow or so I will take the proverbial plunge and try 250 on one of them for 24hrs. If that holds good, then I'll set the second at 250 and let run 24hrs, so on and so forth til I t all four on 250 if I'm lucky.
Between 237.5 & 250, is there any other freqs, I think I saw someone say 240 or something a few pages back.
Ok, so back from the dentist, checked on the four S3's and no x's but I did however notice something weird and maybe it will wind up between now and tomorrow. Anyway, below are as of this post... Elapsed Time, Gh/s(5s) & Gh/s(avg) as well as the HW & the Diff a & r figures. My curiosity is in tthe avg speed of miners 1 & 3 while 2 & 4 look good. Haven't done the HW% math, maybe someone could for me ? lol. Oh ya, all four are OC'd to 237.5 Miner 1Time: 2h 23m 11s 5s: 451.62 Av.: 445.94 HW: 269 Diff A: 867,072 Diff R: 2,560 Miner 2Time: 3h 6m 23s 5s: 471.79 Av.: 474.91 HW: 927 Diff A: 1,222,656 Diff R: 4,096 Miner 3Time: 2h 56m 37s 5s: 468.71 Avg.: 458.37 HW: 86 Diff A: 1,109,504 Diff R: 1,536 Miner 4Time: 3h 6m 6s 5s: 501.62 Avg.: 475.88 HW: 54 Diff A: 1,244,160 Diff R: 1,536 About this time tomorrow I'll use actual pics when it will be ~24hrs that they will all have been up on 237.5. Power consumption?
|
|
|
|
nottm28
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 10:45:16 PM |
|
Could anybody give me any suggestions as to why my antminer seems to be running kinda shit?
Seems to want to only hold 400 gh/s comfortably. Those spikes at the end are the results of reboots. Whenever I reboot it, it runs nicely for a bit, then deteriorates back down to 400. Never seems to be able to hold the 440gh/s as expected.
I have it running off a Corsair 750W PSU with all four PCI-E cables connected so power shouldn't be an issue. It is also running completely stock, I tried overclocking to 'compensate' for this shortfall but even slight overclocks produced great instability and knocked out one of the chips.
I've looked about and this seems kinda like a rare issue but my ant just doesn't want to play ball.
That's typical of ghash - try a different pool
|
donations not accepted
|
|
|
baykan
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 10:50:19 PM |
|
There are 262 pages not easy to read them all.
My S3 will be in my hands tomorrow. What I would like to learn is whether I can use a Butterfly labs 50GH/s Power Supply on Antminer S3 ? I have already bought a 600W PSU with two 6 pin cables because I'm not going to overclock. But if Butterfly labs PSU works with S3 I will give the new one back.
If anybody can give an idea I appreciate...
|
|
|
|
h3rlihy
|
![](https://bitcointalk.org/Themes/custom1/images/post/xx.gif) |
August 14, 2014, 10:55:49 PM |
|
Could anybody give me any suggestions as to why my antminer seems to be running kinda shit?
Seems to want to only hold 400 gh/s comfortably. Those spikes at the end are the results of reboots. Whenever I reboot it, it runs nicely for a bit, then deteriorates back down to 400. Never seems to be able to hold the 440gh/s as expected.
I have it running off a Corsair 750W PSU with all four PCI-E cables connected so power shouldn't be an issue. It is also running completely stock, I tried overclocking to 'compensate' for this shortfall but even slight overclocks produced great instability and knocked out one of the chips.
I've looked about and this seems kinda like a rare issue but my ant just doesn't want to play ball.
That's typical of ghash - try a different pool It's not ghash it's btc guild ![Tongue](https://bitcointalk.org/Smileys/default/tongue.gif)
|
|
|
|
|