gt_addict
|
|
April 26, 2016, 07:31:39 AM |
|
Woohoo!! Little GT-R1 is up to 3rd!!
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
Real-Duke
Legendary
Offline
Activity: 3500
Merit: 2299
Top Crypto Casino
|
|
April 26, 2016, 07:41:45 AM |
|
Hmm why do someone want to cheat with a different miner in a fun race? Btw my baby prepares for the next jump to the pole position
|
|
|
|
RichBC
|
|
April 26, 2016, 09:02:11 AM |
|
I think I have killed RichBC 2... I have been playing around pushing up the Frequency and trying to work out what the incompatibility is with the R1 and higher frequencies on solo.ckpool that does not seem to be there on any other Site. Anyway a wire came off from the Pot that I use to adjust the core voltage and I think that caused the Core Voltage to go way high and has half killed the ASIC. I say half because it will still hash but the rate is very low and there are a large number of HW errors even at very low frequencies. So be careful if you add an adjustment to the voltage to make things a bit more secure than i did.... I have pushed RichBC 1 up to 225Mhz, still completely standard with just a fan blowing on it to keep the temperature down. 225Mhz is the absolute highest I can get an R1 to go on solo.ckpool but can get to 250MHz on any other Pool with just a few HW errors. BTW the frequency in the antrun.de pull down shows 225.25MHz and should just be 225MHz. Rich
|
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
|
April 26, 2016, 09:08:10 AM |
|
I think I have killed RichBC 2... I have been playing around pushing up the Frequency and trying to work out what the incompatibility is with the R1 and higher frequencies on solo.ckpool that does not seem to be there on any other Site. Anyway a wire came off from the Pot that I use to adjust the core voltage and I think that caused the Core Voltage to go way high and has half killed the ASIC. I say half because it will still hash but the rate is very low and there are a large number of HW errors even at very low frequencies. So be careful if you add an adjustment to the voltage to make things a bit more secure than i did.... I have pushed RichBC 1 up to 225Mhz, still completely standard with just a fan blowing on it to keep the temperature down. 225Mhz is the absolute highest I can get an R1 to go on solo.ckpool but can get to 250MHz on any other Pool with just a few HW errors. BTW the frequency in the antrun.de pull down shows 225.25MHz and should just be 225MHz. Rich too bad for RBC2 - that's part of the "fun" in experiments and tinkering with "toys" like this. I learnt a lot from your posts here and also in the other R1 thread and will attempt on my R1 soon, when I get the tools.
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
|
April 26, 2016, 09:11:21 AM |
|
Hmm why do someone want to cheat with a different miner in a fun race? Btw my baby prepares for the next jump to the pole position LOL - i think no one can touch your 13B record at the moment. Anyways... I agree, this R1 race was started as R1 and many people contributed to this R1 mini race with our creative mods within R1 specs, other miners should not be here -- it's like sending F1 car to a F3 race - where's the fun in that?
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
RichBC
|
|
April 26, 2016, 09:19:39 AM |
|
Anyways... I agree, this R1 race was started as R1 and many people contributed to this R1 mini race with our creative mods within R1 specs, other miners should not be here -- it's like sending F1 car to a F3 race - where's the fun in that? Yes and I have to say that it feels a bit like car tuning as well. With increased Voltages, increased Cooling, increased RPM Frequencies and of course some tweeking to the firmware in the ECU Controller. Then the odd blow up....... Rich
|
|
|
|
citronick
Legendary
Offline
Activity: 1834
Merit: 1080
---- winter*juvia -----
|
|
April 26, 2016, 09:23:56 AM |
|
...Then the odd blow up....... LOL -- that's the fun of it.... the missus will prefer if we blow some R1s instead of blowing up an actual engine in the garage.
|
If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 26, 2016, 10:01:30 AM |
|
I think I have killed RichBC 2... I have been playing around pushing up the Frequency and trying to work out what the incompatibility is with the R1 and higher frequencies on solo.ckpool that does not seem to be there on any other Site. Anyway a wire came off from the Pot that I use to adjust the core voltage and I think that caused the Core Voltage to go way high and has half killed the ASIC. I say half because it will still hash but the rate is very low and there are a large number of HW errors even at very low frequencies. So be careful if you add an adjustment to the voltage to make things a bit more secure than i did.... I have pushed RichBC 1 up to 225Mhz, still completely standard with just a fan blowing on it to keep the temperature down. 225Mhz is the absolute highest I can get an R1 to go on solo.ckpool but can get to 250MHz on any other Pool with just a few HW errors. BTW the frequency in the antrun.de pull down shows 225.25MHz and should just be 225MHz. Rich hi Rich, ohh, that's very unfortunate Hmmm, the datasheet says, the Vcore Range is (working) up to 1.1 volt and maximum limit 1.2 Volt Can you reproduce the vcore value you get, at the moment your pot fails? andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
RichBC
|
|
April 26, 2016, 10:14:36 AM |
|
hi Rich, ohh, that's very unfortunate Hmmm, the datasheet says, the Vcore Range is (working) up to 1.1 volt and maximum limit 1.2 Volt Can you reproduce the vcore value you get, at the moment your pot fails? andY Not 100% certain I have a failure but looks like it. Trouble is that the pad I have soldered to came away and I had to find an equivalent point to solder to which was easier said than done because of the low impedance of the Inductor making it difficult to trace what went where. Anyway the voltage adjusts fine so I think I have that correct, but although it will hash it's obviously not right as rate is very low and lots of HW errors even at 100Mhz, what is surprising is that it works at all? To answer your question, at the moment I do not want to go OC again to make a measurement. However without the Pot in circuit there is no feedback from Vout to Pin 1 and I assume that the Buck will wind the volts right up, which could get close to 5V? Rich
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 26, 2016, 10:24:18 AM |
|
Today my first little success, testing R1 with 500MHz@31.43GHs ..but only for a very short time andY Nice.... Was that on ck.solo or another Pool? Rich Short tested with de.ckpool.org... But I´ve recognized another interesting dependence... When I access the R1 Web-Gui, while I test some high frequencies /vcore, so it seems, thats the hashing-job stops earlier, than i kept it untouched... I can measure, power consumption rises, while accessing the Gui, plus 0.1 Watts andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
RichBC
|
|
April 26, 2016, 10:44:49 AM |
|
Today my first little success, testing R1 with 500MHz@31.43GHs ..but only for a very short time andY Nice.... Was that on ck.solo or another Pool? Rich Short tested with de.ckpool.org... But I´ve recognized another interesting dependence... When I access the R1 Web-Gui, while I test some high frequencies /vcore, so it seems, thats the hashing-job stops earlier, than i kept it untouched... I can measure, power consumption rises, while accessing the Gui, plus 0.1 Watts andY Yes I have noticed that dependence, was not certain but always got the feeling that if I was using the Gui that stops were more frequent. Have you tried disabling wireless and stopped the task that controls the U3? Again not certain but I feel that the load reduction reduces stops? Rich
|
|
|
|
andymanone
Sr. Member
Offline
Activity: 432
Merit: 250
Save the past & use the future ©
|
|
April 26, 2016, 10:55:41 AM |
|
Today my first little success, testing R1 with 500MHz@31.43GHs ..but only for a very short time andY Nice.... Was that on ck.solo or another Pool? Rich Short tested with de.ckpool.org... But I´ve recognized another interesting dependence... When I access the R1 Web-Gui, while I test some high frequencies /vcore, so it seems, thats the hashing-job stops earlier, than i kept it untouched... I can measure, power consumption rises, while accessing the Gui, plus 0.1 Watts andY Yes I have noticed that dependence, was not certain but always got the feeling that if I was using the Gui that stops were more frequent. Have you tried disabling wireless and stopped the task that controls the U3? Again not certain but I feel that the load reduction reduces stops? Rich Yes, WIFI is disabled , but U3 task I´ve never touched... Maybe thats an idea, ´cauz I feel too, that there is an dependence "load vs stops" ... andY
|
#Compare your share!# Join the community and be a member of http://www.gekkorun.de today! Open for all Antrouter R1, Gekkoscience Compac, 2PAC and sidehack´s coming soon Bitfury Asic Miners! Notice: gekkorun 2.0 goes offline in 10/07/18 (and will be not longer supported anymore) My previous ANTR1/Gekko Tuning success: Ant R1=500MHz@0.96V@27,66GH/s / Gekko=475MHz@0.9V /stable 450MHz/0.88V@23,78GH/s
|
|
|
minibit
|
|
April 27, 2016, 08:51:50 AM |
|
I think I have killed RichBC 2... I have been playing around pushing up the Frequency and trying to work out what the incompatibility is with the R1 and higher frequencies on solo.ckpool that does not seem to be there on any other Site. Anyway a wire came off from the Pot that I use to adjust the core voltage and I think that caused the Core Voltage to go way high and has half killed the ASIC. I say half because it will still hash but the rate is very low and there are a large number of HW errors even at very low frequencies. So be careful if you add an adjustment to the voltage to make things a bit more secure than i did.... I have pushed RichBC 1 up to 225Mhz, still completely standard with just a fan blowing on it to keep the temperature down. 225Mhz is the absolute highest I can get an R1 to go on solo.ckpool but can get to 250MHz on any other Pool with just a few HW errors. BTW the frequency in the antrun.de pull down shows 225.25MHz and should just be 225MHz. Rich Too bad your R1 is damaged! Thank you for the info about the frequency. We will correct that in the next update.
|
|
|
|
Ant777
Newbie
Offline
Activity: 6
Merit: 0
|
|
April 27, 2016, 09:09:18 PM |
|
It only takes 1 hash.
|
|
|
|
Real-Duke
Legendary
Offline
Activity: 3500
Merit: 2299
Top Crypto Casino
|
|
April 27, 2016, 09:27:02 PM |
|
It only takes 1 hash.
....that is high enough and *BOOOOOM*
|
|
|
|
RichBC
|
|
April 28, 2016, 08:34:08 PM |
|
I think everyone should run the same frequency.
And where would be the fun in that? Rich
|
|
|
|
Real-Duke
Legendary
Offline
Activity: 3500
Merit: 2299
Top Crypto Casino
|
|
April 28, 2016, 08:42:44 PM |
|
I think everyone should run the same frequency.
And where would be the fun in that? Rich Indeed! Everybody should be free to do what he wants to do with his one or more R1's in this race But why do you claim on something while standing in the first position of the leaderboard?
|
|
|
|
gt_addict
|
|
April 28, 2016, 08:49:50 PM |
|
As said previously in this thread. If someone wants to risk damaging their R1 or whatever then so be it. If they score big then bravo for them as the hardwork in experimenting with it has paid off, but the risk of damage and being out of the race is high. Im happy to let my little runt of an R1 hobble along doing his best at the highest freq he will take. He probably wont do any better than his bestever share, but what does it matter. Its the excitement checking in on the website in the vain hope that he may well surprise me and get in the lead for longer than a day lol. Its a "fun run" after all. There's no BTC bet on it.........yet
|
**SUPPORT SIDEHACK** Miner Development Donations to: 1BURGERAXHH6Yi6LRybRJK7ybEm5m5HwTr
Donations/Tips to:- 1GTADDicTXD1uachKKgW24DZDxDGhSMdRa
Join Bitconnect: https://bitconnect.co/?ref=gtaddict
|
|
|
Mikestang
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
April 28, 2016, 10:28:13 PM |
|
lol, are you for real?
You're in the wrong place if you expect to mine a block, and talking trash to those of us that enjoy what we're doing here isn't going to win you any awards.
|
|
|
|
Mikestang
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
April 28, 2016, 10:40:57 PM |
|
Uhm, my what? It's a stock R1 @ 137mHz. I don't take this contest personally, so I don't care what position I am in. 8th is pretty good, top 1/3 for this round so far.
You're funny, like a baby troll in training. Good luck.
|
|
|
|
|