Abcederian
Member
Offline
Activity: 71
Merit: 10
|
|
June 21, 2017, 04:14:09 AM |
|
I apologize for troubling you fellow's I am still searching for a solution. This is what is happening. The miner performs fantastic with 4 cards but when I add a fifth card only 3 cards are running. The 2 cards that are not mining show up in the device manager with code 12 - not enough free resources. This rig consists of the following - CPU G4400 Skylake 1151 Biostar TB 250 4 gb RAM 4 x MSI 1070 8gb Armor , 1 x MSI 1070 gaming 8gb (all on powered risers) EVGA 1000 P2 120 gb SSD Windows 10 64 bit Pro Version 1703 (just updated) I ran into a similar problem with RX 570's and never quite figured out the driver patch until I watched Cryptomined's video. By then I had already switched over to ethOS. Which by the way runs fantastic. To bad there is no support for Nvidia with it. I have 4 rigs running that presently. Rig5 is the first Nvidia rig and today is the first time I have had more than 4 cards. If someone could point me to a link or thread or anything I would really appreciate it. TIA I think your PSU is too thin on power. (5 gpu *150w)+(5risers*25w)+100w for the rest= 975w at 82% performance = 1150w.@ the wall. Thanks for the response. I swapped out a 1300 from a different rig. I am getting the same result. The four card system is drawing 628 according to a killawatt. I have searched just about everything I can think of. I haven't even found anyone else having the same problem. This error won't be related to power or available power, it is most likely due a shortage of PCIe lanes. Are all of your PCIe connectors set to 1.0 or 2.0 in the bios? How can I affect the PCIe lanes on a Biostar tb 250? At the start of the day PCI-e's were set to automatic and were working fine. They are now set to gen 2. That has had no effect on the system. I just changed miner mode to disabled. No effect 3 out of 5 work. Take one off, 4 out 4. I have swapped out one of the armor's for the gaming and 4 out of 4. I replaced the riser on the new card (gaming). same thing 3 of 5 , 4 of 4. Thanks again.
|
|
|
|
|
|
|
The forum strives to allow free discussion of any ideas. All policies are built around this principle. This doesn't mean you can post garbage, though: posts should actually contain ideas, and these ideas should be argued reasonably.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
kinster
Newbie
Offline
Activity: 1
Merit: 0
|
|
June 21, 2017, 04:40:28 AM |
|
hi guys, I have just started mining for awhile and still learning about it. Has anyone experienced that the miner stopped at dev fee accepted, where it just stopped not going forward anymore. (the window is fine) Also, I have read the previous reply where someone say you can restart the system and solve the issue of code 46, by adding the command (-r24) "restart by user"? Does anyone know how to write this command? I have googled it but can't see any hint.
|
|
|
|
Abcederian
Member
Offline
Activity: 71
Merit: 10
|
|
June 21, 2017, 05:12:04 AM |
|
I have got it working! I reflashed the mobo bios. I guess I clicked all the right buttons this time One of those clicks has me wondering, I am not sure I had internal graphics disabled. Thanks to anyone who even thought about the problem. Oh Yeah! This is from the terminal that is mining. Now If I can only figure out why I can't get it in the other room. Where's the beer!
|
|
|
|
zx302
Newbie
Offline
Activity: 14
Merit: 0
|
|
June 21, 2017, 06:47:21 AM |
|
Hi All, Need some help. I have a Biostar TB85 board with 2 Gigabyte GTX 1080 cards installed. I installed a fresh Win10 64 (think it is the Creation Ver, downloaded with Media Creation Tool). Run all the updates and tried to mine with this miner and also CCminer. Changed the info in the .bat file to mine and ran it. I get stratum time out. https://drive.google.com/open?id=0BzMjsxCLio_tLU41S2htUm5aUjgThis is connected to a switch that already has 1 AMD rig running without an issue. Tried disabling AV/FW/FW in router. And nothing helps Any idea? TYIA ZX Well, if anyone cares. What solved it was a firmware update and reset of my Asus router. Weird, worked with ETH stratum before the upgrade but that fixed it. Good luck all.
|
|
|
|
nUm81
|
|
June 21, 2017, 07:15:30 AM |
|
I have got it working! I reflashed the mobo bios. I guess I clicked all the right buttons this time One of those clicks has me wondering, I am not sure I had internal graphics disabled. Thanks to anyone who even thought about the problem. Oh Yeah! This is from the terminal that is mining. Now If I can only figure out why I can't get it in the other room. Where's the beer! If you want to be able to access the page from other PC's on your network, change the 127.0.0.1 to the IP address of the mining pc in your config file. It's probably a good idea to assign the unit a static IP address while you are at it. Once you make the change you may get a firewall notice that pops up the first time you start the miner with the changed address.
|
|
|
|
pablox
Newbie
Offline
Activity: 15
Merit: 0
|
|
June 21, 2017, 07:21:18 AM |
|
You don't need to add a full line with IP, just --api. Then type 127.0.0.1:42000 in browser and you will see stats.
Thanks. Now work. But work only in local computer with ewbf. How can open from another computer/ipad?
|
|
|
|
Tidsdilatation
|
|
June 21, 2017, 07:26:39 AM |
|
You don't need to add a full line with IP, just --api. Then type 127.0.0.1:42000 in browser and you will see stats.
Thanks. Now work. But work only in local computer with ewbf. How can open from another computer/ipad? Yes, you need to open the port 42000 in your router and then connect to your WANIP :42000
|
|
|
|
BadAstroZA
|
|
June 21, 2017, 07:36:46 AM |
|
I have got it working! I reflashed the mobo bios. I guess I clicked all the right buttons this time One of those clicks has me wondering, I am not sure I had internal graphics disabled. Thanks to anyone who even thought about the problem. Oh Yeah! This is from the terminal that is mining. Now If I can only figure out why I can't get it in the other room. Where's the beer! Wow, that is impressive. Care to share your overclock settings? I'm trying to figure out what the sweet spot is. Do I push core clock, or should I focus on mem clock? Can I reduce the voltage down quite a bit? Going to start experimenting now, but some pointers would be appreciated! Thanks
|
|
|
|
Bulletdodger
|
|
June 21, 2017, 07:50:47 AM |
|
I hope 1080Ti's dont start dying on us with 0.3.4, I plan on getting quite a few of them.
|
_
|
|
|
c400
Newbie
Offline
Activity: 1
Merit: 0
|
|
June 21, 2017, 08:04:19 AM |
|
dear EWBF_, can you please add an ability to work api in this way: or or even i do have dynamic ip thx
|
|
|
|
buzzkillb
|
|
June 21, 2017, 08:26:59 AM |
|
1080's on Hush
|
|
|
|
timbereagle
|
|
June 21, 2017, 08:39:54 AM |
|
Hello, api results shows as text, not like graphics.
How can I fix it?
{"method":"getstat", "error":null, "start_time":1498033895, "current_server":"eu1-zcash.flypool.org:3333", "available_servers":1, "server_status":2, "result":[{"gpuid":0, "cudaid":0, "busid":"0000:01:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":70, "gpu_power_usage":91, "speed_sps":279, "accepted_shares":12, "rejected_shares":0, "start_time":1498033897},{"gpuid":1, "cudaid":1, "busid":"0000:03:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":72, "gpu_power_usage":90, "speed_sps":263, "accepted_shares":11, "rejected_shares":0, "start_time":1498033897},{"gpuid":2, "cudaid":2, "busid":"0000:06:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":70, "gpu_power_usage":91, "speed_sps":287, "accepted_shares":10, "rejected_shares":0, "start_time":1498033897},{"gpuid":3, "cudaid":3, "busid":"0000:07:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":71, "gpu_power_usage":89, "speed_sps":281, "accepted_shares":5, "rejected_shares":0, "start_time":1498033898},{"gpuid":4, "cudaid":4, "busid":"0000:08:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":67, "gpu_power_usage":93, "speed_sps":279, "accepted_shares":10, "rejected_shares":0, "start_time":1498033898},{"gpuid":5, "cudaid":5, "busid":"0000:09:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":59, "gpu_power_usage":85, "speed_sps":214, "accepted_shares":10, "rejected_shares":0, "start_time":1498033898}]}
|
|
|
|
nUm81
|
|
June 21, 2017, 08:50:24 AM |
|
Hello, api results shows as text, not like graphics.
How can I fix it?
{"method":"getstat", "error":null, "start_time":1498033895, "current_server":"eu1-zcash.flypool.org:3333", "available_servers":1, "server_status":2, "result":[{"gpuid":0, "cudaid":0, "busid":"0000:01:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":70, "gpu_power_usage":91, "speed_sps":279, "accepted_shares":12, "rejected_shares":0, "start_time":1498033897},{"gpuid":1, "cudaid":1, "busid":"0000:03:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":72, "gpu_power_usage":90, "speed_sps":263, "accepted_shares":11, "rejected_shares":0, "start_time":1498033897},{"gpuid":2, "cudaid":2, "busid":"0000:06:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":70, "gpu_power_usage":91, "speed_sps":287, "accepted_shares":10, "rejected_shares":0, "start_time":1498033897},{"gpuid":3, "cudaid":3, "busid":"0000:07:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":71, "gpu_power_usage":89, "speed_sps":281, "accepted_shares":5, "rejected_shares":0, "start_time":1498033898},{"gpuid":4, "cudaid":4, "busid":"0000:08:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":67, "gpu_power_usage":93, "speed_sps":279, "accepted_shares":10, "rejected_shares":0, "start_time":1498033898},{"gpuid":5, "cudaid":5, "busid":"0000:09:00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":59, "gpu_power_usage":85, "speed_sps":214, "accepted_shares":10, "rejected_shares":0, "start_time":1498033898}]}
Just remove the /getstat from the link.
|
|
|
|
timbereagle
|
|
June 21, 2017, 08:52:43 AM |
|
Hello, api results shows as text, not like graphics.
How can I fix it?
00.0", "name":"GeForce GTX 1060 6GB", "gpu_status":2, "solver":0, "temperature":59, "gpu_power_usage":85, "speed_sps":214, "accepted_shares":10, "rejected_shares":0, "start_time":1498033898}]}
Just remove the /getstat from the link. Thanks!
|
|
|
|
timbereagle
|
|
June 21, 2017, 09:37:12 AM |
|
You don't need to add a full line with IP, just --api. Then type 127.0.0.1:42000 in browser and you will see stats.
Thanks. Now work. But work only in local computer with ewbf. How can open from another computer/ipad? Yes, you need to open the port 42000 in your router and then connect to your WANIP :42000 I opened port 42000 however WANIP:42000 not working . I put my public ip on "WANIP" I have multiple rigs on that IP, is it a reason?
|
|
|
|
nUm81
|
|
June 21, 2017, 09:58:45 AM |
|
You don't need to add a full line with IP, just --api. Then type 127.0.0.1:42000 in browser and you will see stats.
Thanks. Now work. But work only in local computer with ewbf. How can open from another computer/ipad? Yes, you need to open the port 42000 in your router and then connect to your WANIP :42000 I opened port 42000 however WANIP:42000 not working . I put my public ip on "WANIP" I have multiple rigs on that IP, is it a reason? If you want to use your WAN IP you will need to use a router to forward the requests with the port numbers on to the correct rig. Each individual rig will need to be set to its local IP + a port number that is unique for router to forward to. ie. 192.168.1.1:42001 - rig1 192.168.1.2:42002 - rig2 192.168.1.3:42003 - rig3 ect. then you just need to setup the corresponding forwards in the WAN router to direct each unique port to the correct local IP.
|
|
|
|
timbereagle
|
|
June 21, 2017, 10:01:56 AM |
|
You don't need to add a full line with IP, just --api. Then type 127.0.0.1:42000 in browser and you will see stats.
Thanks. Now work. But work only in local computer with ewbf. How can open from another computer/ipad? Yes, you need to open the port 42000 in your router and then connect to your WANIP :42000 I opened port 42000 however WANIP:42000 not working . I put my public ip on "WANIP" I have multiple rigs on that IP, is it a reason? If you want to use your WAN IP you will need to use a router to forward the requests with the port numbers on to the correct rig. Each individual rig will need to be set to its local IP + a port number that is unique for router to forward to. ie. 192.168.1.1:42001 - rig1 192.168.1.2:42002 - rig2 192.168.1.3:42003 - rig3 ect. then you just need to setup the corresponding forwards in the WAN router to direct each unique port to the correct local IP. Thank you. I am not a tech guy. therefore I will not be able to do it
|
|
|
|
nUm81
|
|
June 21, 2017, 10:07:45 AM |
|
You don't need to add a full line with IP, just --api. Then type 127.0.0.1:42000 in browser and you will see stats.
Thanks. Now work. But work only in local computer with ewbf. How can open from another computer/ipad? Yes, you need to open the port 42000 in your router and then connect to your WANIP :42000 I opened port 42000 however WANIP:42000 not working . I put my public ip on "WANIP" I have multiple rigs on that IP, is it a reason? If you want to use your WAN IP you will need to use a router to forward the requests with the port numbers on to the correct rig. Each individual rig will need to be set to its local IP + a port number that is unique for router to forward to. ie. 192.168.1.1:42001 - rig1 192.168.1.2:42002 - rig2 192.168.1.3:42003 - rig3 ect. then you just need to setup the corresponding forwards in the WAN router to direct each unique port to the correct local IP. Thank you. I am not a tech guy. therefore I will not be able to do it It really is quite easy, you just need to connect to your modem, it will most likely have port forwarding options. If you can get a mining rig up and running, I'm sure you can figure out the port forwarding.
|
|
|
|
totikk
Newbie
Offline
Activity: 73
Merit: 0
|
|
June 21, 2017, 10:26:15 AM |
|
Can someone write a small program - a monitor? Like ETHmon, by Claymore's for his miner. To collect data from several IP / rigs? For Windows, and for Android too )
|
|
|
|
lanmi88
Newbie
Offline
Activity: 25
Merit: 0
|
|
June 21, 2017, 11:53:59 AM |
|
Hello all,
I've been working on optimizing the miner for windows and linux.
Here's my most optimal current setup:
miner v0.3.3b GTX 1070 Windows 7 90% TDP +200 Core Clock +700 Memory Clock 450 Sol/s
I'd prefer to mine in linux, and my initial setup attempt with ubuntu 16.10 - I've not been able to get overclocking to work right so it seems it is at stock - but at 100% TDP, it seems I'm only getting 420sol/s.
Has anyone been able to get better numbers with linux at all or should I stick with Windows 7? I've had a very frustrating time working with trying to get the overclock to work, doesn't seem to be functional via the GUI.
Maximum overclock for Zotac mini's (my electricity is free): Zotac 1050 Mini 157-159 sol/s : core +165, mem +650, operates at 73 - 75C degrees; even core +168 goes quiet unstable, mem goes unstable after +700, and lay down at +750 Zotac 1060 Mini 289-297 sol/s: core +185, mem +750, 71 - 73C; core up to 205 but a little unstable, mem at 900 lays down. Do u mine Ethereum with Zotac 1060 Mini and whtas ur hasrate? ty
|
|
|
|
|