Antminer D3 Blissz firmware (10/12 v1.12 update)

[blissz]

as I have enough feedback from people that own a watt meter I will make a version available for everybody (with the correct defaults / limits). Thank you for your patience

[detonyle]

Flash OK...
look fine at the moment
what is the 'default asic voltage' Value?

[crackfoo]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

[mohicans]

hooray!!! found this thread and its awesome... congrats to blissz... looking forward to another success of yours!!
cheers!!!

[blissz]

Flash OK...
look fine at the moment
what is the 'default asic voltage' Value?

good to hear. I don't know what the default value is to be honest as I modified my hardware and don't know the hardware defaults.
That's why I need your guys feedback about wattages

[D3 Antminer]

this was a good one.
will  keep our   hopes alive  for the big one

[blissz]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

[crackfoo]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

[blissz]

the firmware is send to 4 people now. Need a few more with a wattmeter 

[crackfoo]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

After flashing but not adjusting the voltage yet:

https://pasteboard.co/GTUSfol.png

[detonyle]

Flash OK...
look fine at the moment
what is the 'default asic voltage' Value?

good to hear. I don't know what the default value is to be honest as I modified my hardware and don't know the hardware defaults.
That's why I need your guys feedback about wattages

I mean in your modified interface you have the option asic voltage with range 200-460,  was is the default value, to know where to start and decrease it

[blissz]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

After flashing but not adjusting the voltage yet:

https://pasteboard.co/GTUSfol.png

please adjust it down a lot the default is way too high I see. Try to get it at the same levels as before flashing.

[blissz]

Flash OK...
look fine at the moment
what is the 'default asic voltage' Value?

good to hear. I don't know what the default value is to be honest as I modified my hardware and don't know the hardware defaults.
That's why I need your guys feedback about wattages

I mean in your modified interface you have the option asic voltage with range 200-460,  was is the default value, to know where to start and decrease it

the default should be 360, but that seems higher than the default voltage

[crackfoo]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

After flashing but not adjusting the voltage yet:

https://pasteboard.co/GTUSfol.png

please adjust it down a lot the default is way too high I see. Try to get it at the same levels as before flashing

yup, temps went up pretty quick.

Here is voltage at lowest setting. Looks good, no errors and my xxxxx's are gone too ^_^

https://pasteboard.co/GTUUEgS.png

[D3 Antminer]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

After flashing but not adjusting the voltage yet:

https://pasteboard.co/GTUSfol.png

do you think that these temps are sustainable  ?

[blissz]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

After flashing but not adjusting the voltage yet:

https://pasteboard.co/GTUSfol.png

please adjust it down a lot the default is way too high I see. Try to get it at the same levels as before flashing

yup, temps went up pretty quick.

Here is voltage at lowest setting. Looks good, no errors and my xxxxx's are gone too ^_^

https://pasteboard.co/GTUUEgS.png

This is at 200? Seems that 200 is more near to the original setting.

[crackfoo]

do you think that these temps are sustainable  ?

of course not. see my next post with the lower voltage.

[crackfoo]

here mine with bitmain latest firmware:

https://pasteboard.co/GTUNZug.png

my board 2 has always been flaky.

Thanks now let's try to get roughly the same temperatures with my firmware as I'm curious what the default voltage is. After that test try to lower the voltage as low as you can go

ps. you're unlucky by the way: one of your boards is giving HW errors at default voltage....

I know, I have 2 other D3's still in the box so maybe I'll give those a try too.

After flashing but not adjusting the voltage yet:

https://pasteboard.co/GTUSfol.png

please adjust it down a lot the default is way too high I see. Try to get it at the same levels as before flashing

yup, temps went up pretty quick.

Here is voltage at lowest setting. Looks good, no errors and my xxxxx's are gone too ^_^

https://pasteboard.co/GTUUEgS.png

This is at 200? Seems that 200 is more near to the original setting.

yup 200.

[blissz]

200 seems to be close to the original firmware then. Maybe slightly lower voltage, but that would be a good default.
I will make a new image as the range is not good now. It should be more like a 100 - 300 range I think

Important note to the testers: the default voltage on the new firmware is too high, please set it to 200 and wait for further information.

I will come back with a new version which has a valid range, sorry for the inconvenience

[Maicol792]

My beta test start this evening ..you can compile whit latest cgminer version .. and we want test other algo sub X11 ...