Antminer D3 Blissz firmware (10/12 v1.12 update)

[zerocom]

Hello blissz I've read a few posts and see you do a great job, I wanted to ask you there will be a chance to add new algorithms? or change from x11 to scrypt?
can you put a switch to change pools like in the baikal and add some of the others? thanks and sorry for my english.

I will wait for an even more stable version to upgrade. thanks for your job.

[1714985967]

1714985967

[1714985967]

1714985967

[1714985967]

1714985967

[JACKSEG]

Hello

What do you think about that ?

https://www.power-antminer.xyz

It's possible  

[slv1221]

Hello

What do you think about that ?

https://www.power-antminer.xyz

It's possible  

its SCAM

[Sfitzjava]

Hello

What do you think about that ?

https://www.power-antminer.xyz

It's possible  

Seriously if you want to throw bitcoins away on a scam I would be happy to send you a Bitcoin address to send it to.

These guys literally started this site TODAY.   This has SCAM written all over.  Most likely it's the inginer.xyz guys realizing they have been marked as a scam and starting a new shop... Or someone else seeing all the traffic and going to try their had at scamming people.  

If it's too good to be true ( ehm.. D3 <cough>) then it most likely is.  

However Blissz stuff is Majorly AWESOME!!!    
Before this latest version  I was getting 18.5mhs @1100w,   now I'm at 19.5 (sometime 20) @1099w.

Great stuff here!!

[DragosD1]

Hi,
noticed again 0.000 hash with 55/60 chips alive on one board.
No restart with latest version. Probably because of missing xxxxx....
Kernel log attached, as promised

https://drive.google.com/open?id=1cqlZkDF6rBW8uKWeMkU2Zj1MAzS_oTdI

[SimpleCoin8]

Hi Bliss, the chip temperatures are wacky with this new update. It either shows very low or high temps on one chain, 14 or 125 degrees C. Every time I reboot the miner it will change between low or high temps.

[tperalta82]

Stupid question, at 444Mhz, whats your outlet power usage?

I'm not getting anything lower than 900, using the lowest voltage settings

[crackfoo]

Stupid question, at 444Mhz, whats your outlet power usage?

I'm not getting anything lower than 900, using the lowest voltage settings

I'm at 456Mhz @ 850w doing 17Gh

[ruptan]

hi all

does anyone know why people seem to be selling their d3's cheaper than you can buy them from bitmain on ebay?

Simple. It not profitable anymore. Stop buying Antminers!!

[tperalta82]

Stupid question, at 444Mhz, whats your outlet power usage?

I'm not getting anything lower than 900, using the lowest voltage settings

I'm at 456Mhz @ 850w doing 17Gh

Are you running Bitmain psu?

[crackfoo]

Stupid question, at 444Mhz, whats your outlet power usage?

I'm not getting anything lower than 900, using the lowest voltage settings

I'm at 456Mhz @ 850w doing 17Gh

Are you running Bitmain psu?

no, an EVGA 1600w T2 platinum

[tperalta82]

Stupid question, at 444Mhz, whats your outlet power usage?

I'm not getting anything lower than 900, using the lowest voltage settings

I'm at 456Mhz @ 850w doing 17Gh

Are you running Bitmain psu?

no, an EVGA 1600w T2 platinum

That may be my issue, although i don't want to believe it lol, i'm running HP Server PSU 1200w with the adapter for antminers

[may142012]

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

[tperalta82]

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt, as for the HW errors, i wouldn't be concerned with those values

[may142012]

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

[tperalta82]

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

Yes, if it works stable like that, just keep those values

[may142012]

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

Yes, if it works stable like that, just keep those values

LOL, i just set to the frequency to 425, my third chain and second chain are starting to give HWs, and the third chain shows some xxx

Do i have to reboot the miner after change something?

[Wananavu99]

hi all

does anyone know why people seem to be selling their d3's cheaper than you can buy them from bitmain on ebay?

Simple. It not profitable anymore. Stop buying Antminers!!

I agree.  I racked up a large bill this black Friday, buying several GPUs, 1 mobo and other mining hardware.  Cyber monday sucked bad, not much deals at all. 

[tperalta82]

Can any expert review my miner? I am using Blissz's latest firmware. Should i improve something here?

Fans are set to "Auto Default"

Frequency = 400

Voltage = Lowest

All three boards are using global settings.

https://gyazo.com/5f393def36645af0a01a922cd156819c

This is a result after an hour:

https://gyazo.com/fb5a6a1a1ede35bacc98c0e49847c3cc

Here is the calculation from the wall.

Watts = 727

Amps = 6.2

Voltage = 118v

I guess you could run it way higher, like 444 or 456 an extra juice will not hurt

Ok, what's about voltage? Should i leave it "Lowest"? Auto default fans?

Yes, if it works stable like that, just keep those values

LOL, i just set to the frequency to 425, my third chain and second chain are starting to give HWs, and the third chain shows some xxx

Do i have to reboot the miner after change something?

strange, what PSU are you running?

[dalu1]

Blissz,

Your newest firmware 28/11 crashes right after 2 hours when it tries to switch from pool 3 to pool 0.  I am flashing back to your 26/11 version.