[ANN] TeamRedMiner v0.10.10 - Ironfish/Kaspa/ZIL/Kawpow/Etchash and More

[cryptdigger]

can somebody help me? how can i turn on the compute mode on the tearedminer?
and can somebody share me the oc numbers for rx6800xt? thx

use --enable_compute, have to run as administrator

thank you bro

[System2K]

is it possible to add the memory timings in the bat file instead of using amd memory tweak?

[nik-qz]

is it possible to add the memory timings in the bat file instead of using amd memory tweak?

look at here
https://github.com/Eliovp/amdmemorytweak

[Tokechan]

I recently switched to teamredminer from phoenix and I see that teamredminer also can use claymore's remote manager.  It was very convenient to change wallet or pool using remote manager function "edit config.txt" or "send config.txt". I tried to create config.txt in teamredminer folder and run it from teamredminer.exe but it didn't work. Can I somehow set a config.txt file for teamredminer like claymore's or phoenix's config.txt with miner settings?

[System2K]

is it possible to add the memory timings in the bat file instead of using amd memory tweak?

look at here
https://github.com/Eliovp/amdmemorytweak

i added these commands in the bat file but trm starts for a second and closes
--cl 18 --ras 26 --rcdrd 12 --rcdwr 4 --rc 37 --rp 13 --rrds 3 --rrdl 4 --rtp 6 --faw 13 --cwl 7 --wtrs 5 --wtrl 5 --wr 14 --rrefd 7 --rdrddd 3 --rdrdsd 2 --rdrdsc 1 --rdrdscl 3 --wrwrdd 3 --wrwrsd 2 --wrwrsc 1 --wrwrscl 3 --wrrd 1 --rdwr 17 --ref 21000 --mrd 4 --mod 12 --xs 216 --xsmrs 216 --pd 7 --cksre 8 --cksrx 8 --rfcpb 148 --stag 7 --xp 7 --cpded 2 --cke 7 --rddata 17 --wrlat 5 --rdlat 14 --wrdata 1 --ckestag 2 --rfc 208

[nik-qz]

is it possible to add the memory timings in the bat file instead of using amd memory tweak?

look at here
https://github.com/Eliovp/amdmemorytweak

i added these commands in the bat file but trm starts for a second and closes
--cl 18 --ras 26 --rcdrd 12 --rcdwr 4 --rc 37 --rp 13 --rrds 3 --rrdl 4 --rtp 6 --faw 13 --cwl 7 --wtrs 5 --wtrl 5 --wr 14 --rrefd 7 --rdrddd 3 --rdrdsd 2 --rdrdsc 1 --rdrdscl 3 --wrwrdd 3 --wrwrsd 2 --wrwrsc 1 --wrwrscl 3 --wrrd 1 --rdwr 17 --ref 21000 --mrd 4 --mod 12 --xs 216 --xsmrs 216 --pd 7 --cksre 8 --cksrx 8 --rfcpb 148 --stag 7 --xp 7 --cpded 2 --cke 7 --rddata 17 --wrlat 5 --rdlat 14 --wrdata 1 --ckestag 2 --rfc 208

try to set several parameters, if everything is ok, add it and you will understand why it did not start
if you have 580 cards, then why raise the -tref parameter for these cards, it is enough to set the value to 30

[Littlegrand]

switching from Phoenix to TRM what are people using to control clocks/mem(did bios for timings).  Ideally it would be a program that can be run using command line like Phoenix but prior to TRM running?

Thanks

[nik-qz]

switching from Phoenix to TRM what are people using to control clocks/mem(did bios for timings).  Ideally it would be a program that can be run using command line like Phoenix but prior to TRM running?

Thanks

look at here
https://bitcointalk.org/index.php?topic=5059817.msg56418010#msg56418010

[Littlegrand]

switching from Phoenix to TRM what are people using to control clocks/mem(did bios for timings).  Ideally it would be a program that can be run using command line like Phoenix but prior to TRM running?

Thanks

look at here
https://bitcointalk.org/index.php?topic=5059817.msg56418010#msg56418010

I saw that but it says you cannot use a driver newer than 20.5 and TRM recommends newer drivers?

[nik-qz]

switching from Phoenix to TRM what are people using to control clocks/mem(did bios for timings).  Ideally it would be a program that can be run using command line like Phoenix but prior to TRM running?

Thanks

look at here
https://bitcointalk.org/index.php?topic=5059817.msg56418010#msg56418010

I saw that but it says you cannot use a driver newer than 20.5 and TRM recommends newer drivers?

if you use drivers older than 20.5.1, then the miner will be slightly less efficient in speed and power, but if you use more recent drivers than 20.5.1, then the OverdriveNTool program for changing the voltage most likely will not work, so it is optimal to use version 20.5.1

[Littlegrand]

switching from Phoenix to TRM what are people using to control clocks/mem(did bios for timings).  Ideally it would be a program that can be run using command line like Phoenix but prior to TRM running?

Thanks

look at here
https://bitcointalk.org/index.php?topic=5059817.msg56418010#msg56418010

I saw that but it says you cannot use a driver newer than 20.5 and TRM recommends newer drivers?

if you use drivers older than 20.5.1, then the miner will be slightly less efficient in speed and power, but if you use more recent drivers than 20.5.1, then the OverdriveNTool program for changing the voltage most likely will not work, so it is optimal to use version 20.5.1

Thanks,

There is no other program that can do it?  Any plans on TRM adding this feature?

[invaer]

Hi guys, there is a strange problem with TeamRedMiner 0.8.1 on the Kawpow algorithm.
TeamRedMiner has full support for Awesome Miner.
But when you start TeamRedMiner through the Awesome Miner interface, TeamRedMiner crashes at this point:
https://i.imgur.com/pIbjpVU.png
At the same time, if you start TeamRedMiner manually, then it works.
If you run diagnostics in Awesome Miner, then everything works in it.
Also Awesome Miner shows error accessing TeamRedMiner API:
https://i.imgur.com/rOMJ9Kg.png
This problem occurs on different rigs with different video cards.
All other Kawpow miners (Nanominer NBminer) work fine and have no API errors:
https://i.imgur.com/vLEGttU.png
I would be grateful if someone could help 

[Littlegrand]

I am trying to switch to TRM from Phoenix.

I am using Windows 10 Driver 20.11.1

This is my current config:
teamredminer.exe -a ethash -o stratum+tcp://pool -u EthAddress.Miner1 -p x -d 2,3,5 --enable_compute --eth_aggr_mode --fan_control=65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80

I use overdriven to change the cards clock/mem/volt

I have 1 RX5700Xt and 2 RX570.  The rx570s work fine but when I start, TRM detects the 5700 DEAD for a while then starts loading the dag and then mines at around 1k/h second or so.

I am trying the suggested speeds of 1275 core, 1750mem and 850 volts.

Any ideas why this is doing it?  This card can run up to 57mh/s on Phoenix

Thanks

[nik-qz]

I am trying to switch to TRM from Phoenix.

I am using Windows 10 Driver 20.11.1

This is my current config:
teamredminer.exe -a ethash -o stratum+tcp://pool -u EthAddress.Miner1 -p x -d 2,3,5 --enable_compute --eth_aggr_mode --fan_control=65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80

I use overdriven to change the cards clock/mem/volt

I have 1 RX5700Xt and 2 RX570.  The rx570s work fine but when I start, TRM detects the 5700 DEAD for a while then starts loading the dag and then mines at around 1k/h second or so.

I am trying the suggested speeds of 1275 core, 1750mem and 850 volts.

Any ideas why this is doing it?  This card can run up to 57mh/s on Phoenix

Thanks

when you use the AMD_Memory_Tweak or AMD_Memory_Tweak_XL program?, it must be run before the start of mining, so that it will enter the necessary parameters, if you run it during operation, then the 5700 video card will fall off (this is what happens to me), if this is not the case, try removing the --eth_aggr_mode parameter and instead choose a softer mode --eth_config=A

[Littlegrand]

I am trying to switch to TRM from Phoenix.

I am using Windows 10 Driver 20.11.1

This is my current config:
teamredminer.exe -a ethash -o stratum+tcp://pool -u EthAddress.Miner1 -p x -d 2,3,5 --enable_compute --eth_aggr_mode --fan_control=65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80

I use overdriven to change the cards clock/mem/volt

I have 1 RX5700Xt and 2 RX570.  The rx570s work fine but when I start, TRM detects the 5700 DEAD for a while then starts loading the dag and then mines at around 1k/h second or so.

I am trying the suggested speeds of 1275 core, 1750mem and 850 volts.

Any ideas why this is doing it?  This card can run up to 57mh/s on Phoenix

Thanks

when you use the AMD_Memory_Tweak or AMD_Memory_Tweak_XL program?, it must be run before the start of mining, so that it will enter the necessary parameters, if you run it during operation, then the 5700 video card will fall off (this is what happens to me), if this is not the case, try removing the --eth_aggr_mode parameter and instead choose a softer mode --eth_config=A

I am not using amdmemtweak, I flashed the bios and then I used the Overdriven GUI tool to change the core/mem/volt and started TRM. I have tried it without the --eth_aggr_mode and same thing.

[nik-qz]

I am trying to switch to TRM from Phoenix.

I am using Windows 10 Driver 20.11.1

This is my current config:
teamredminer.exe -a ethash -o stratum+tcp://pool -u EthAddress.Miner1 -p x -d 2,3,5 --enable_compute --eth_aggr_mode --fan_control=65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80

I use overdriven to change the cards clock/mem/volt

I have 1 RX5700Xt and 2 RX570.  The rx570s work fine but when I start, TRM detects the 5700 DEAD for a while then starts loading the dag and then mines at around 1k/h second or so.

I am trying the suggested speeds of 1275 core, 1750mem and 850 volts.

Any ideas why this is doing it?  This card can run up to 57mh/s on Phoenix

Thanks

when you use the AMD_Memory_Tweak or AMD_Memory_Tweak_XL program?, it must be run before the start of mining, so that it will enter the necessary parameters, if you run it during operation, then the 5700 video card will fall off (this is what happens to me), if this is not the case, try removing the --eth_aggr_mode parameter and instead choose a softer mode --eth_config=A

I am not using amdmemtweak, I flashed the bios and then I used the Overdriven GUI tool to change the core/mem/volt and started TRM. I have tried it without the --eth_aggr_mode and same thing.

then try not to run Overdriven GUI and see what happens
and also this program amdmemtweak is still needed, even if not for 5700 video cards, but for 570 by raising the -tref parameter that cannot be flashed into the BIOS
for video cards 5700 amdmemtweak can change the voltage parameters of the memory controller and the memory itself, as well as SOK

[Littlegrand]

I am trying to switch to TRM from Phoenix.

I am using Windows 10 Driver 20.11.1

This is my current config:
teamredminer.exe -a ethash -o stratum+tcp://pool -u EthAddress.Miner1 -p x -d 2,3,5 --enable_compute --eth_aggr_mode --fan_control=65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80

I use overdriven to change the cards clock/mem/volt

I have 1 RX5700Xt and 2 RX570.  The rx570s work fine but when I start, TRM detects the 5700 DEAD for a while then starts loading the dag and then mines at around 1k/h second or so.

I am trying the suggested speeds of 1275 core, 1750mem and 850 volts.

Any ideas why this is doing it?  This card can run up to 57mh/s on Phoenix

Thanks

when you use the AMD_Memory_Tweak or AMD_Memory_Tweak_XL program?, it must be run before the start of mining, so that it will enter the necessary parameters, if you run it during operation, then the 5700 video card will fall off (this is what happens to me), if this is not the case, try removing the --eth_aggr_mode parameter and instead choose a softer mode --eth_config=A

I am not using amdmemtweak, I flashed the bios and then I used the Overdriven GUI tool to change the core/mem/volt and started TRM. I have tried it without the --eth_aggr_mode and same thing.

then try not to run Overdriven GUI and see what happens
and also this program amdmemtweak is still needed, even if not for 5700 video cards, but for 570 by raising the -tref parameter that cannot be flashed into the BIOS
for video cards 5700 amdmemtweak can change the voltage parameters of the memory controller and the memory itself, as well as SOK

That was the issue. Ive not used amdmemtweak. Do you use amdmemtweak or amdmemtweakxl?  I looked it up and most posts are for the GUI and/or just timings but I flashed the timings. Would you have an example command line in windows for the 5700 for core/mem/volt?  

Thanks

[nik-qz]

That was the issue. Ive not used amdmemtweak. Do you use amdmemtweak or amdmemtweakxl?  Would you have an example command line in windows for the 5700 for core/mem/volt? 

Thanks

amdmemtweak for Polaris
C:\Miner\AMD_Memory\WinAMDTweak.exe --i 0 --ref 30

amdmemtweakxl for Navi10 in test mode windows
https://fastpic.ru/view/114/2021/0315/_27af50bd914220b59f4a8176512eeeb5.png.html

[Littlegrand]

That was the issue. Ive not used amdmemtweak. Do you use amdmemtweak or amdmemtweakxl?  Would you have an example command line in windows for the 5700 for core/mem/volt? 

Thanks

amdmemtweak for Polaris
C:\Miner\AMD_Memory\WinAMDTweak.exe --i 0 --ref 30

amdmemtweakxl for Navi10 in test mode windows
https://fastpic.ru/view/114/2021/0315/_27af50bd914220b59f4a8176512eeeb5.png.html

Is there a way to set Navi/Polaris clocks/mem/volt from the command line such as(and this is made up):
amdmemtweakxl -i 0 --vddci 718 --mvdd 1264 --SOC 825

Thanks

[lxspector]

Is it possible to add the ability to switch mining from ETH to ZIL by a timer inside the miner, as implemented in Nanominer? Using a proxy is not good at all. Please make a syntax in which you can specify more than just the 0x address. but login for example from MRR [user.123456]. Lolminer removes the "." as a mistake