CCminer(SP-MOD) Modded GPU kernels.

[zTheWolfz]

This is quark right?

try  -i 22.9 (the default for 750ti)

Do you have more than one card in the rig? Is the card trottling? Check the temperature, if it reaches 70 degress c it will automaticly downclock,. Also make sure your card is in the p0 state. Defalt is p2


Performance modes
P8 = idle clock speeds and lowest power consumption
P2 = the default mode used when your PC boots or no drivers are installed.
P0 = Gaming/Load. This mode only accepts boost/offset values


Did you build it yourself? Use cuda 6.5 and not cuda 7.0 or 7.5

-i 22.9 seems to help gotten it back close, I had already tried -i 23 before posting. I'll try tweaking it a little more.
Card hardly ever gets over mid 50c so heat or throttling is not a problem. Yes have cuda 6.5 in use. W7 64bit per your .exe file.
Almost all my rigs are open air bench setups, so heat is not much of a problem with anything with the AC running  

[lawrencelyl]

For this release 59, I'm using -X intensity parameter instead of -i.  My older setting of "-i 23" seems not working well for me.
So, I dropped -i and used -X instead (setting the cuda threads count).

Here's what I found:

Release 58 and before:
-i 23 == 8388608 cuda threads
-i 24 == 16777216 cuda threads (default value if you don't specify any intensity)

Release 59:
-X 128 = 8388608 cuda threads
-X 256 = 16777216 cuda threads

Basically, number of cuda threads = 256 * 256 * (value of X)
sp mentioned it few posts above.  Please correct me if I misinterpreted anything

[joblo]

Here's a heads up about performance states. nividia-settings powermizer has it backwards.

All discussions I have seen refer to 0 as the highest performance level and this is confirmed
with nvidia-smi.

But nvidia-settings powermizer has them reversed with level zero as the lowest and
level 4 as the highest performance level.

All of my previous posts were using the powermizer values so I apologize for any confusion.
I will be more clear in the future.

[zTheWolfz]

57 with -i 22.9 will test 59 with -X 128/256 now.



59 -X 128 below -X 256 was at 9970 max. no SS at 256 saw no need.

[sp_]

Wich driver are you using?

Can you try release 58?

[lawrencelyl]

57 with -i 22.9 will test 59 with -X 128/256 now.



59 -X 128 below -X 256 was at 9970 max. no SS at 256 saw no need.

For GTX960, probably you'll want to try with "-X 64" or somewhere between 64 to 128.
For my GTX970/980, I'm using -X 128.  I limit the TDP of the card, so lower CUDA threads count scores better.

[zTheWolfz]

Wich driver are you using?

Can you try release 58?

Driver 353.30, sorry no more time to test today got to get some sleep.
Quick note with 57 & command line -i 22.9 -l 16x24 its showing me hash in this range.

@ Law I tried -x 64 and 96 in test, no help with 59 for my setup.

Code:

 accepted: 62/62 (100.00%), 10258 khash/s yay!!!
 quark.usa.nicehash.com:3345 quark block 2028639
 GPU #0: GeForce GTX 960, 10301
 quark.usa.nicehash.com:3345 quark block 2028640
 GPU #0: GeForce GTX 960, 10204
 GPU #0: GeForce GTX 960, 10211
 accepted: 63/63 (100.00%), 10254 khash/s yay!!!
 GPU #0: GeForce GTX 960, 10234
 accepted: 64/64 (100.00%), 10249 khash/s yay!!!
 quark.usa.nicehash.com:3345 quark block 2028641
 GPU #0: GeForce GTX 960, 10249
 GPU #0: GeForce GTX 960, 10304
 accepted: 65/65 (100.00%), 10251 khash/s yay!!!
 GPU #0: GeForce GTX 960, 10238
 accepted: 66/66 (100.00%), 10253 khash/s yay!!!
 GPU #0: GeForce GTX 960, 10194
 accepted: 67/67 (100.00%), 10251 khash/s yay!!!
 GPU #0: GeForce GTX 960, 10222
 accepted: 68/68 (100.00%), 10249 khash/s yay!!!

[bensam1231]

So a friendly update cause I'm sure you guys don't watch your power meters. Release 59 for Neo increases power usage by 30w per 970. I went from 190w to 220w.

That's a 15% increase in power usage. I only saw about a 5% increase in hashrate for Neo as well. I have since reverted to .56 as the new version reduces efficiency quite a bit.

[Slava_K]

Today Lyra2 v2 start?

[djm34]

Today Lyra2 v2 start?

already started...

[facanferff]

In API it doesn't give me the correct fan percent/rpm (localhost:4068/hwinfo)...

GPU=0;BUS=1;CARD=GeForce GTX 850M;SM=500;MEM=2147483648;TEMP=66.0;FAN=0;RPM=0;FREQ=901500;MEMFREQ=900000;PST=P0;VID=10de;PID=1391;NVML=-1;NVAPI=0;SN=;BIOS=82.07.47.00.05|OS=windows;NVDRIVER=353.62;CPUS=8;CPUTEMP=0;CPUFREQ=0|�

Also, I noticed NVML=-1, is it normal?

[sp_]

I have compiled it with the api disabled as default:

in ccminer.cpp:


int opt_api_listen = 0; /* 0 to disable */

[facanferff]

I have compiled it with the api disabled as default:

in ccminer.cpp:


int opt_api_listen = 0; /* 0 to disable */

I'm running with parameters:
--api-bind=127.0.0.1:4068 -b 0.0.0.0:4068

Is it normal to give 0 to fan percent/rpm, but giving correct temperature?

[joblo]

There's a problem with neoscrypt in r59.

It uses 100% of a cpu core for each thread, Linux and Windows.

[pallas]

There's a problem with neoscrypt in r59.

It uses 100% of a cpu core for each thread, Linux and Windows.

I've found the (regression) bug, will post the fix asap.
This will also reduce power consumption ;-)

[sp_]

already fixed it..

[pallas]

already fixed it..

You beat me to it... Sorry for the trouble.

[sp_]

I am merging Djm34's new lyra2 now.

[frazier34567]

already fixed it..

Recompiled it and when I try neoscript I get
6X750 ti Evga SC Windows 8.1 Pro VS 2013 Driver 353.30

Edited to show command line

[15:04:29] Starting WestHash NeoScrypt with ccminer.exe -o stratum+tcp://neoscrypt.usa.nicehash.com:3341 -a neoscrypt -u x -p x
[2015-08-10 15:04:30] Starting Stratum on stratum+tcp://neoscrypt.usa.nicehash.com:3341
[2015-08-10 15:04:30] NVAPI GPU monitoring enabled.
[2015-08-10 15:04:30] Binding thread 1 to cpu 1 (mask 2)
[2015-08-10 15:04:30] 6 miner threads started, using 'neoscrypt' algorithm.
[2015-08-10 15:04:30] Binding thread 4 to cpu 0 (mask 10)
[2015-08-10 15:04:30] Binding thread 0 to cpu 0 (mask 1)
[2015-08-10 15:04:30] Binding thread 3 to cpu 3 (mask 
[2015-08-10 15:04:30] Binding thread 2 to cpu 2 (mask 4)
[2015-08-10 15:04:30] Binding thread 5 to cpu 1 (mask 20)
[2015-08-10 15:04:30] Stratum difficulty set to 64
[2015-08-10 15:04:30] neoscrypt.usa.nicehash.com:3341 neoscrypt block 829453
*** ccminer 1.5.59-git(SP-MOD) for nVidia GPUs by sp-hash@github ***
Cuda error in func 'scanhash_neoscrypt' at line 48 : out of memory.
   Built with VC++ 2013 and nVidia CUDA SDK 6.5

  Based on pooler cpuminer 2.3.2 and the tpruvot@github fork
   CUDA support by Christian Buchner, Christian H. and DJM34
  Includes optimizations implemented by sp , klaust, tpruvot and tsiv.

[scryptr]

I am merging Djm34's new lyra2 now.

DJM34 and VTC--

His ccminer truly rocks on VTC!        --scryptr