Bitmain's Released Antminer S9, World's First 16nm Miner Ready to Order

[mamiakimo]

today one of my 2 antminer s9 B12 get dead board with XXX status
after restart it work for 15 minutes and stop again
any idea ??

You can swap the psu's for each machine.  then check and see if the problem follows the psu  if the problem follows the psu it is a psu issue.

So swap psus and get back to us if the same board fails or not .

i moved the board to another machine and it failed also after 30 minutes
i sent it to them, it's second board dead from 3 S9 that mean 20% damages

[mamiakimo]

bitmain remove about 8 from this small pieces used to dissipate Chip temperature ( i don't know it's name )
on S9/550 to make it higher temp than S9/600 and sell it on different batch
that what i saw when i opened my B12 today

[mamiakimo]

[Tupsu]

i moved the board to another machine and it failed also after 30 minutes
i sent it to them, it's second board dead from 3 S9 that mean 20% damages

I think that your  not working  miners %  is 66% , if you have only one  miner perfectly fine.

[sidehack]

But if you look at failed boards, he's 2 of 9 for 22% failures.

Also, I would bet the heatsinks were removed on those boards because right in front of the fan the topside heatsinks will be sufficient, and removing the backside heatsinks especially right near the fan motor will improve airflow (less backpressure and ducting) for heatsinks farther down the board and keep the whole thing cooler overall.

[Tupsu]

But if you look at failed boards, he's 2 of 9 for 22% failures.

....

If I look my 9 replaced S9 boards from 23 miners , it is only 6 broken miners from 23, that  is 26%

If I Calculating from broken boards, than it is 9 from total 69 boards = only 13%

The fact is, that today is the first day, if I have all 69 hashboards in my hands.

From the first day one or more hashboards were on their way to China, or back . But I was never missing more than 3 hashboards at a time.

It does only one or less broken miner from 23.  Only 4,75%    in the three-month  period.

[aarons6]

the s7 and s9 was a bad design.. thermally.
the heatsinks right behind the fan in the center by the motor part of the fan get no air at all..

they should have added a 1 inch spacer on the intake and exhaust fan to help, but even then those front sinks are in a dead spot.
also having those tiny heatsinks all over the place not even lined up is not helping either.

at the very least they should have made some jig to hold the heatsinks and make them all perfectly lined up.

[philipma1957]

the s7 and s9 was a bad design.. thermally.
the heatsinks right behind the fan in the center by the motor part of the fan get no air at all..

they should have added a 1 inch spacer on the intake and exhaust fan to help, but even then those front sinks are in a dead spot.
also having those tiny heatsinks all over the place not even lined up is not helping either.

at the very least they should have made some jig to hold the heatsinks and make them all perfectly lined up.

My mod should fix this as the unit will be a little longer.

[aarons6]

the s7 and s9 was a bad design.. thermally.
the heatsinks right behind the fan in the center by the motor part of the fan get no air at all..

they should have added a 1 inch spacer on the intake and exhaust fan to help, but even then those front sinks are in a dead spot.
also having those tiny heatsinks all over the place not even lined up is not helping either.

at the very least they should have made some jig to hold the heatsinks and make them all perfectly lined up.

My mod should fix this as the unit will be a little longer.

yes something like this 3d printed that channeled the air through the miner would be pretty helpful.
http://www.shapeways.com/product/D432AXVMR/120mm-pc-fan-4-quot-duct-adapter?li=gmerchant&utm_source=google&utm_medium=cpc&gclid=CjwKEAjwjqO_BRDribyJpc_mzHgSJABdnsFW5xuBkLKLffraFLHtTKsU0LL7bnNXyPZdWIPfLIkmMBoC0Tnw_wcB

[philipma1957]

the s7 and s9 was a bad design.. thermally.
the heatsinks right behind the fan in the center by the motor part of the fan get no air at all..

they should have added a 1 inch spacer on the intake and exhaust fan to help, but even then those front sinks are in a dead spot.
also having those tiny heatsinks all over the place not even lined up is not helping either.

at the very least they should have made some jig to hold the heatsinks and make them all perfectly lined up.

My mod should fix this as the unit will be a little longer.

yes something like this 3d printed that channeled the air through the miner would be pretty helpful.
http://www.shapeways.com/product/D432AXVMR/120mm-pc-fan-4-quot-duct-adapter?li=gmerchant&utm_source=google&utm_medium=cpc&gclid=CjwKEAjwjqO_BRDribyJpc_mzHgSJABdnsFW5xuBkLKLffraFLHtTKsU0LL7bnNXyPZdWIPfLIkmMBoC0Tnw_wcB

my goal is to make two miners.  

order a second controller.    so you get a 2 board miner fully stock

  and pull one board cut the post to length from mount it here and you get a one board miner which you can downclock run in house and it needs under a 750 watt psu.

Cost is not bad and if you have 5 or 6 s9s like I do  this gives you spare parts plus let you tinker.


http://www.homedepot.com/p/Veranda-4-in-x-4-in-x-6-ft-White-Vinyl-Square-Fence-Post-73010699/202084744

[kodokbuduk]

Waaaaaaa 
no heatsink?? 

[mamiakimo]

this heatsinks existing on my B600 boards and not existing on my B550 boards

[kodokbuduk]

this heatsinks existing on my B600 boards and not existing on my B550 boards

yes i know. so we cannot just install firmware B600 into B550.
They removed some heatsinks on B550..geeezzzz, 

[HagssFIN]

That doesn't make technically any sense, it must be a manufacturing failure or something?

[in2tactics]

Do you have any photos?

[philipma1957]

Do you have any photos?

I do. Give me a minute.

[mamiakimo]

they removed this heatsinks to make it heater and cannot overclock on the future
so they have more temp than B600 all the time
cgminer display maximum chip temp on the panel and they removed many of it to make PCB temp get high too
so you can't overclock it

[fusion0389]

Just received my fith S9 12.93, i ordered from Bitmain Warranty here in the USA. After booting it up, the first hashboard had unusually high temperatures. Even after reducing the clock speed to 550 the first hashboard was still running at 101. Meanwhile, the rest of my S9's are running under 100 at stock or close to stock clock speeds. I had to reduce the hashrate to 525 in order to get this machine to stay under 100 degrees... A bit abnormal if you ask me... I went ahead and submitted a request with Bitmain Warranty regarding the issue to see what we can do about this. Anyone else have similar experience?


https://flic.kr/p/MBLxh7

[MyRig]

Prepaid UPS Shipping Label sent to you for the return.  Full Refund be provided to you.  Please check your ticket!

Just received my fith S9 12.93, i ordered from Bitmain Warranty here in the USA. After booting it up, the first hashboard had unusually high temperatures. Even after reducing the clock speed to 550 the first hashboard was still running at 101. Meanwhile, the rest of my S9's are running under 100 at stock or close to stock clock speeds. I had to reduce the hashrate to 525 in order to get this machine to stay under 100 degrees... A bit abnormal if you ask me... I went ahead and submitted a request with Bitmain Warranty regarding the issue to see what we can do about this. Anyone else have similar experience?


https://flic.kr/p/MBLxh7

[BITMAIN]

Dear Bitcoiners,

Our offices will be closed October 01-07 in observance of the Chinese National Day. Logistics will be out and no fixes will be made during that period. Responses to your inquiries may be delayed as a result.

Please visit support.bitmain.com for troubleshooting or for leaving us a message.

Regards,

the Bitmain team