Bitcoin Forum
December 05, 2024, 01:01:36 AM *
News: Latest Bitcoin Core release: 28.0 [Torrent]
 
   Home   Help Search Login Register More  
Pages: « 1 ... 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 [56] 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 »
  Print  
Author Topic: A4 Dominator - Pre-Order Group Buy - 280mh, roughly 1000w, $1800 + shipping  (Read 122584 times)
Eyedol-X
Hero Member
*****
Offline Offline

Activity: 952
Merit: 508



View Profile
December 08, 2016, 06:30:38 PM
 #1101

hi everyone, i want to share my experience with the miner software version, the V2.0.2 did great job. 5 X a4 running for now 6 day without any trouble, no pool disconnect and very stable
thanks you to inno for the support and the very good service, i recommand it to everyone, look like all problem is solve with this new version


You really came all this way to make an account and as your first post is to share your endorsement of Innosilicon and information "no pool disconnect and very stable" when there are pages of evidence to the contrary?

Sorry, but I call bullshit on your post.
Lay94
Newbie
*
Offline Offline

Activity: 42
Merit: 0


View Profile
December 08, 2016, 07:03:00 PM
 #1102

I was asked by Dominique from Innosilicon to share my experience.

I have 3rd batch miners, were very unstable with original v2.0.1

After I got v2.0.2 from them, it seems relatively stable on mono-coin pool (f2pool)

Miners tend to die (completely disappear) on switching pools - work for ~12 h on prohashing, then I have to reboot as they disappear from network.

Probably overheating, but it is hard to say - I can not watch then all the time.

If somebody managed to get them stable on prohashing - could you please share settings?

I will probably try them on nicehash - original firmware would not work there at all, did not try new one.

Will watch this thread closely
FlensGold
Legendary
*
Offline Offline

Activity: 1405
Merit: 1001


View Profile
December 09, 2016, 10:45:13 AM
 #1103

Did anyone try to power those miners with the Bitmaintech APW-1600 PSUs( https://shop.bitmain.com/productDetail.htm?pid=00020160905064759862LCcn24oJ0685 ) ?
Do you see any problems by using these or should I use ATX PSUs?
collectiveseven
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
December 09, 2016, 11:55:15 AM
 #1104

I was asked by Dominique from Innosilicon to share my experience.

I have 3rd batch miners, were very unstable with original v2.0.1

After I got v2.0.2 from them, it seems relatively stable on mono-coin pool (f2pool)

Miners tend to die (completely disappear) on switching pools - work for ~12 h on prohashing, then I have to reboot as they disappear from network.

Probably overheating, but it is hard to say - I can not watch then all the time.

If somebody managed to get them stable on prohashing - could you please share settings?

I will probably try them on nicehash - original firmware would not work there at all, did not try new one.

Will watch this thread closely

I have them stable on prohashing for almost 24hours.

2hr avg hashrate: 277.98 MH/s

Speed: 1200Mhz
mV: 820
Diff: 8192

Eyedol-X
Hero Member
*****
Offline Offline

Activity: 952
Merit: 508



View Profile
December 09, 2016, 12:02:13 PM
 #1105

I was asked by Dominique from Innosilicon to share my experience.

I have 3rd batch miners, were very unstable with original v2.0.1

After I got v2.0.2 from them, it seems relatively stable on mono-coin pool (f2pool)

Miners tend to die (completely disappear) on switching pools - work for ~12 h on prohashing, then I have to reboot as they disappear from network.

Probably overheating, but it is hard to say - I can not watch then all the time.

If somebody managed to get them stable on prohashing - could you please share settings?

I will probably try them on nicehash - original firmware would not work there at all, did not try new one.

Will watch this thread closely

I have them stable on prohashing for almost 24hours.

2hr avg hashrate: 277.98 MH/s

Speed: 1200Mhz
mV: 820
Diff: 8192



my best at PH has been about 48-72hrs
collectiveseven
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
December 09, 2016, 01:24:43 PM
 #1106

I was asked by Dominique from Innosilicon to share my experience.

I have 3rd batch miners, were very unstable with original v2.0.1

After I got v2.0.2 from them, it seems relatively stable on mono-coin pool (f2pool)

Miners tend to die (completely disappear) on switching pools - work for ~12 h on prohashing, then I have to reboot as they disappear from network.

Probably overheating, but it is hard to say - I can not watch then all the time.

If somebody managed to get them stable on prohashing - could you please share settings?

I will probably try them on nicehash - original firmware would not work there at all, did not try new one.

Will watch this thread closely

I have them stable on prohashing for almost 24hours.

2hr avg hashrate: 277.98 MH/s

Speed: 1200Mhz
mV: 820
Diff: 8192



my best at PH has been about 48-72hrs

I will update again after the weekend Smiley
Lay94
Newbie
*
Offline Offline

Activity: 42
Merit: 0


View Profile
December 09, 2016, 03:30:31 PM
 #1107

I was asked by Dominique from Innosilicon to share my experience.

I have 3rd batch miners, were very unstable with original v2.0.1

After I got v2.0.2 from them, it seems relatively stable on mono-coin pool (f2pool)

Miners tend to die (completely disappear) on switching pools - work for ~12 h on prohashing, then I have to reboot as they disappear from network.

Probably overheating, but it is hard to say - I can not watch then all the time.

If somebody managed to get them stable on prohashing - could you please share settings?

I will probably try them on nicehash - original firmware would not work there at all, did not try new one.

Will watch this thread closely

I have them stable on prohashing for almost 24hours.

2hr avg hashrate: 277.98 MH/s

Speed: 1200Mhz
mV: 820
Diff: 8192



my best at PH has been about 48-72hrs

I will update again after the weekend Smiley

Prohashing - 12h so far.

Hashrate fluctuates between 200MH/s and 300MH/s

Voltage set at 810.

Temperature of boards - 64 degrees. Seems overheating, I guess...

Miners are in a cold room, and it is winter now. I can not put them in a freezer...  Huh

What temperature is deemed as normal? I read before somebody says miners run at 40? How is that possible?

Mine are jumping to 60 almost right away.
collectiveseven
Newbie
*
Offline Offline

Activity: 11
Merit: 0


View Profile
December 09, 2016, 03:52:38 PM
 #1108

Mine are 48-51
Lay94
Newbie
*
Offline Offline

Activity: 42
Merit: 0


View Profile
December 09, 2016, 04:07:14 PM
 #1109

Mine are 48-51

Anything special you do for this?
Longsnowsm (OP)
Hero Member
*****
Offline Offline

Activity: 868
Merit: 517


View Profile
December 09, 2016, 04:29:24 PM
 #1110

I just got some good news from Chloe.  They are planning to arrange to flash or upgrade the MCU's.  They are looking for someone who can flash the units in the US or replace the MCU's.  I will reach out to @lightfoot to see if he is interested.  Inno plans to pay for this repair.

FryguyUK
Legendary
*
Offline Offline

Activity: 801
Merit: 1000


View Profile
December 09, 2016, 04:42:57 PM
 #1111

Hey could somebody upload or point me to towards the batch 3 v2.0.x files, the most recent.. ?

Thanks
citronick
Legendary
*
Offline Offline

Activity: 1834
Merit: 1080


---- winter*juvia -----


View Profile
December 09, 2016, 04:54:22 PM
 #1112

Hey could somebody upload or point me to towards the batch 3 v2.0.x files, the most recent.. ?

Thanks

Quote
Here is the link of v2.0.2. If you have batch 3 miners please update.
https://www.dropbox.com/s/9umhsbtky6t1c6j/2.0.2beta.rar?dl=0

For batch 1 and 2 users, we are preparing sending the MCU/jigs for updating the MCU firmware to you recently. Just some patience please. We will fix everything for you.

If I provided you good and useful info or just a smile to your day, consider sending me merit points to further validate this Bitcointalk account ~ useful for future account recovery...
Lay94
Newbie
*
Offline Offline

Activity: 42
Merit: 0


View Profile
December 09, 2016, 04:54:51 PM
 #1113

Hey could somebody upload or point me to towards the batch 3 v2.0.x files, the most recent.. ?

Thanks

I got this

https://www.dropbox.com/s/9umhsbtky6t1c6j/2.0.2beta.rar?dl=0
lightfoot
Legendary
*
Offline Offline

Activity: 3206
Merit: 2314


I fix broken miners. And make holes in teeth :-)


View Profile
December 09, 2016, 05:03:23 PM
 #1114

I just got some good news from Chloe.  They are planning to arrange to flash or upgrade the MCU's.  They are looking for someone who can flash the units in the US or replace the MCU's.  I will reach out to @lightfoot to see if he is interested.  Inno plans to pay for this repair.
Sure. Would be happy to help.

Eyedol-X
Hero Member
*****
Offline Offline

Activity: 952
Merit: 508



View Profile
December 09, 2016, 06:10:56 PM
 #1115

I just got some good news from Chloe.  They are planning to arrange to flash or upgrade the MCU's.  They are looking for someone who can flash the units in the US or replace the MCU's.  I will reach out to @lightfoot to see if he is interested.  Inno plans to pay for this repair.
Sure. Would be happy to help.



Great news! -- Thanks for your efforts for the community.
FryguyUK
Legendary
*
Offline Offline

Activity: 801
Merit: 1000


View Profile
December 09, 2016, 06:26:08 PM
 #1116

thanks for the speedy response chaps, top shelf as we brits say
Longsnowsm (OP)
Hero Member
*****
Offline Offline

Activity: 868
Merit: 517


View Profile
December 09, 2016, 06:46:18 PM
 #1117

I am sure they plan to do something like this in the EU part of the world also.  So we will need to see if we can get the details for who that person would be in the EU for these repairs.
firehawk71
Full Member
***
Offline Offline

Activity: 136
Merit: 100


View Profile
December 10, 2016, 05:42:03 PM
 #1118

I just got some good news from Chloe.  They are planning to arrange to flash or upgrade the MCU's.  They are looking for someone who can flash the units in the US or replace the MCU's.  I will reach out to @lightfoot to see if he is interested.  Inno plans to pay for this repair.


This sounds good as I live in the USA.. Please keep us updated on how we get in line for the repair what I need to do ect.. Thanks!
firehawk71
Full Member
***
Offline Offline

Activity: 136
Merit: 100


View Profile
December 10, 2016, 05:45:12 PM
 #1119

I just got some good news from Chloe.  They are planning to arrange to flash or upgrade the MCU's.  They are looking for someone who can flash the units in the US or replace the MCU's.  I will reach out to @lightfoot to see if he is interested.  Inno plans to pay for this repair.
Sure. Would be happy to help.


lightfoot are you located in the US? I am in Missouri.. Thanks
lightfoot
Legendary
*
Offline Offline

Activity: 3206
Merit: 2314


I fix broken miners. And make holes in teeth :-)


View Profile
December 10, 2016, 08:51:14 PM
 #1120

ightfoot are you located in the US? I am in Missouri.. Thanks
Yes, I'm in the US.

C
Pages: « 1 ... 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 [56] 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 »
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2006-2009, Simple Machines Valid XHTML 1.0! Valid CSS!