[ANN] Technobit HEX16B(Bitfury based) 16 chip board design

[loshia]

Finlay - Build two instances one for HEX boards (enable hex boards only) one for whatever you want not patched and run them simultaneously - two instances. USBPOOLING is disabled (commented out and thread will never start) and there is a big chance bfl not to work if it uses cancelable USB transfers and so on

[Pentium100]

It finally compiled and works now. And my single CPU control PC is at load 2.5. I will build a faster PC for this (just replaced bad caps on the motherboard) and it should work great. I will try overclocking.

How do I specify to cgminer that it should not use the bfl device? I could then run bfgminer for the Single.

[loshia]

It finally compiled and works now. And my single CPU control PC is at load 2.5. I will build a faster PC for this (just replaced bad caps on the motherboard) and it should work great. I will try overclocking.

How do I specify to cgminer that it should not use the bfl device? I could then run bfgminer for the Single.

As i sad ./autogen.sh --enable-heminerb Only. you will see BFL disabled in the summary Enable only what you need. About CPU usage - I have seen Tplink Cpu at load 45% with 10 HEXA boards....can you post top output? you will see what is loading your cpu but if cgminer was compiled for HEX boards only it shall load 2-5% you cpu assuming you do have one board only

[cbrboot]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

[loshia]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

It is overclocked already to safest value. Check voltage to be 900 and clock 540. Do not go above 540 clock it is not working. Try voltage if you feel brave

[Zich]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

It is overclocked already to safest value. Check voltage to be 900 and clock 540. Do not go above 540 clock it is not working. Try voltage if you feel brave

Changelog

Code:

HEX16A(Avalon1): Best results 7.4-7.7 Gh/s (16 chips) in terms of stability and clocking are observed at 1460mV core voltage + 480 MHz Clock.


HEX16B(Bitfury): Best results 44.5-45 Gh/s (16 chips) in terms of stability and clocking are observed at 900mV core voltage + 540 Clock. 
Do not go above 540 it is not working!


HEX16C(Avalon2): To be tested with 10 chips - 1100mV core voltage + 1500 MHz Clock.

[Pentium100]

It finally compiled and works now. And my single CPU control PC is at load 2.5. I will build a faster PC for this (just replaced bad caps on the motherboard) and it should work great. I will try overclocking.

How do I specify to cgminer that it should not use the bfl device? I could then run bfgminer for the Single.

As i sad ./autogen.sh --enable-heminerb Only. you will see BFL disabled in the summary Enable only what you need. About CPU usage - I have seen Tplink Cpu at load 45% with 10 HEXA boards....can you post top output? you will see what is loading your cpu but if cgminer was compiled for HEX boards only it shall load 2-5% you cpu assuming you do have one board only

OK, I will recompile it when I transfer it to the faster PC.

top output:

Code:

top - 11:28:00 up 1 day, 20:21,  5 users,  load average: 2.98, 3.22, 2.84
Tasks:  71 total,   2 running,  69 sleeping,   0 stopped,   0 zombie
%Cpu(s): 43.9 us, 46.9 sy,  0.0 ni,  9.0 id,  0.0 wa,  0.0 hi,  0.2 si,  0.0 st
KiB Mem:     60012 total,    58280 used,     1732 free,     3564 buffers
KiB Swap:   123900 total,    11712 used,   112188 free,    31900 cached

  PID USER      PR  NI  VIRT  RES  SHR S  %CPU %MEM    TIME+  COMMAND                                                                      
24097 root      20   0  156m 5656 2668 R  85.7  9.4  27:58.16 cgminer                                                                      
24142 root      20   0  4424 1388 1032 R   5.0  2.3   0:01.59 top                                                                          
 9632 root      20   0  9200 1228  932 S   0.7  2.0   0:11.84 sshd                                                                         
    1 root      20   0  2192  536  508 S   0.2  0.9   0:29.06 init      
...

The PC is just slow. It was enough for the Single, but obviously not enough for these boards. The CPU is Cyrix MediaGX 233MHz. I have another PC with Celeron 1GHz (TDP 30W), will use that later.

[Gator-hex]

Has anyone found any limit to the number of Hex16b you can USB to the TL-MR3020 router?

[simoncc]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

Well…l am still waiting for mine, and no tracking number there in my order history…

[loshia]

Has anyone found any limit to the number of Hex16b you can USB to the TL-MR3020 router?

Unlimited

I am joking from a point on i think performance will suffer
But most probably 9-15 will be ok. If you happen to see performance lost just buy second tplink or use Linux PC in that case

[Zich]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

Well…l am still waiting for mine, and no tracking number there in my order history…

I fear that your HEX16B is being used by speedy employee to mining right now.

They used my HEX16A for almost 3 week  





Just Kidding. loshia force me to do it  

[wuzamarine]

I would NOT do business with Technobit.eu. This damn fool will rob you blind.
He disappeared with my $1k a month ago.
Just vanished.

[simoncc]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

Well…l am still waiting for mine, and no tracking number there in my order history…

I fear that your HEX16B is being used by speedy employee to mining right now.

They used my HEX16A for almost 3 week  





Just Kidding. loshia force me to do it  

Oh…
This is my first time to order HEX16B, and I want to know how long it takes to ship from there to me...

[marto74]

I would NOT do business with Technobit.eu. This damn fool will rob you blind.
He disappeared with my $1k a month ago.
Just vanished.

I'm here just busy
order ref please

[marto74]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

Well…l am still waiting for mine, and no tracking number there in my order history…

I fear that your HEX16B is being used by speedy employee to mining right now.

They used my HEX16A for almost 3 week  





Just Kidding. loshia force me to do it  

Oh…
This is my first time to order HEX16B, and I want to know how long it takes to ship from there to me...

Now you can order with January shipment

[Zich]

Oh…
This is my first time to order HEX16B, and I want to know how long it takes to ship from there to me...

About 3-4 days if using DHL or UPS express saver. Maybe you can ask marto by giving order reference & order date. You see that marto just thought that you are just want to order not already order 

I hope all of technoBTCit customer will stated the order reference & order date when asking about order status to make it more quick & easy  

[simoncc]

I finally got my order!
I see a lot of default entry's in the tplink configuration of cgminer, is there any manual on how to safely overclock it?

Well…l am still waiting for mine, and no tracking number there in my order history…

I fear that your HEX16B is being used by speedy employee to mining right now.

They used my HEX16A for almost 3 week  





Just Kidding. loshia force me to do it  

Oh…
This is my first time to order HEX16B, and I want to know how long it takes to ship from there to me...

Now you can order with January shipment

Yes, l like to place another order, but the first one is not coming,  and I have to know how long it takes to ship to me. So Martin, go go go

[berny81]

@marto74, i try to write here because with mail to support and private message i have no response and i see that you read this treadh.

i receive my order YMPWFNJVE of 3 nanofury usb but 1 of them is not working.on windows i see it on device manager and on linux i see as microchip device, but bfgminer don't recognize it and led remain off.
i made all possible try but 1 of them is dead

what can i do?

[simoncc]

Hi Marto74, this is mine: Order Reference EVWMJYXQI -- placed on 2013-11-20
Please, do me a favor to tell me about my order status. Thanks
 

[Morpheus21]

I received my order today! after 4week. true explain by Marto
 a little difficult to make it work but perfect
 

I have many questions but now I don't know where to start 

 I use "windows" to work  a thread somewhere to have some answer? 


Possible to get Serial USB driver for 64BIT?


Thank you Martin;