Littlegrand
Jr. Member
Offline
Activity: 104
Merit: 5
|
|
March 15, 2021, 07:13:58 PM |
|
I am trying to switch to TRM from Phoenix.
I am using Windows 10 Driver 20.11.1
This is my current config: teamredminer.exe -a ethash -o stratum+tcp://pool -u EthAddress.Miner1 -p x -d 2,3,5 --enable_compute --eth_aggr_mode --fan_control=65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80,65::::20:80
I use overdriven to change the cards clock/mem/volt
I have 1 RX5700Xt and 2 RX570. The rx570s work fine but when I start, TRM detects the 5700 DEAD for a while then starts loading the dag and then mines at around 1k/h second or so.
I am trying the suggested speeds of 1275 core, 1750mem and 850 volts.
Any ideas why this is doing it? This card can run up to 57mh/s on Phoenix
Thanks
when you use the AMD_Memory_Tweak or AMD_Memory_Tweak_XL program?, it must be run before the start of mining, so that it will enter the necessary parameters, if you run it during operation, then the 5700 video card will fall off (this is what happens to me), if this is not the case, try removing the --eth_aggr_mode parameter and instead choose a softer mode --eth_config=A I am not using amdmemtweak, I flashed the bios and then I used the Overdriven GUI tool to change the core/mem/volt and started TRM. I have tried it without the --eth_aggr_mode and same thing. then try not to run Overdriven GUI and see what happens and also this program amdmemtweak is still needed, even if not for 5700 video cards, but for 570 by raising the -tref parameter that cannot be flashed into the BIOS for video cards 5700 amdmemtweak can change the voltage parameters of the memory controller and the memory itself, as well as SOK That was the issue. Ive not used amdmemtweak. Do you use amdmemtweak or amdmemtweakxl? I looked it up and most posts are for the GUI and/or just timings but I flashed the timings. Would you have an example command line in windows for the 5700 for core/mem/volt? Thanks
|
|
|
|
|
Littlegrand
Jr. Member
Offline
Activity: 104
Merit: 5
|
|
March 15, 2021, 07:29:24 PM |
|
Is there a way to set Navi/Polaris clocks/mem/volt from the command line such as(and this is made up): amdmemtweakxl -i 0 --vddci 718 --mvdd 1264 --SOC 825 Thanks
|
|
|
|
lxspector
Newbie
Offline
Activity: 3
Merit: 0
|
|
March 17, 2021, 10:51:34 PM |
|
Is it possible to add the ability to switch mining from ETH to ZIL by a timer inside the miner, as implemented in Nanominer? Using a proxy is not good at all. Please make a syntax in which you can specify more than just the 0x address. but login for example from MRR [user.123456]. Lolminer removes the "." as a mistake
|
|
|
|
reza_irani
Newbie
Offline
Activity: 2
Merit: 0
|
|
March 18, 2021, 10:57:25 AM |
|
hi everyone I've faced an issue recently when I'm mining eth with team reader 0.8.0 on ethermine pool everything is ok but when I want to move to 2miners pool the bellow error appear I'm mining with simple mining os and all configuration is ok
Pool asia-eth.2miners.com rpc method _mining.authorize_ timed out after 69 seconds. Reconnecting.
I've tried all pool addresses and SSL connection but the problem is still arise can anyone help me?
|
|
|
|
Littlegrand
Jr. Member
Offline
Activity: 104
Merit: 5
|
|
March 18, 2021, 11:48:45 AM |
|
hi everyone I've faced an issue recently when I'm mining eth with team reader 0.8.0 on ethermine pool everything is ok but when I want to move to 2miners pool the bellow error appear I'm mining with simple mining os and all configuration is ok
Pool asia-eth.2miners.com rpc method _mining.authorize_ timed out after 69 seconds. Reconnecting.
I've tried all pool addresses and SSL connection but the problem is still arise can anyone help me?
Best to show your launch line with more information:) Your line should look something like this for windows if thats what you are using: teamredminer.exe -a ethash -o stratum+tcp://us-eth.2miners.com:2020 -u ADDRESS.MINERNAME -p x --enable_compute --watchdog_script
|
|
|
|
Cabeimac
Newbie
Offline
Activity: 1
Merit: 0
|
|
March 18, 2021, 01:24:33 PM |
|
Good afternoon everyone,
I was mining steadily with a solid rate of 200mh/s. I tried to overclock a bit more my cards but now I am not able to make RaveOs to recognise my seven cards. I have deleted all OC settings from the platform. Maybe there is something that I can set in order to reboot the miner every time my cards are not recognised?
Cards are not even recognised as "DEAD", they are just not being recognised by TRM nor RaveOs.
Many thanks in advance.
Kind regards,
Cabeimac.
|
|
|
|
reza_irani
Newbie
Offline
Activity: 2
Merit: 0
|
|
March 18, 2021, 02:58:22 PM |
|
hi everyone I've faced an issue recently when I'm mining eth with team reader 0.8.0 on ethermine pool everything is ok but when I want to move to 2miners pool the bellow error appear I'm mining with simple mining os and all configuration is ok
Pool asia-eth.2miners.com rpc method _mining.authorize_ timed out after 69 seconds. Reconnecting.
I've tried all pool addresses and SSL connection but the problem is still arise can anyone help me?
Best to show your launch line with more information:) Your line should look something like this for windows if thats what you are using: teamredminer.exe -a ethash -o stratum+tcp://us-eth.2miners.com:2020 -u ADDRESS.MINERNAME -p x --enable_compute --watchdog_script thanks the lunch line is -a ethash -o stratum+tcp://us-eth.2miners.com:2020 -u *****.$rigName -p x --api_listen --watchdog_script in windows we need teamredminer.exe and enable_compute which is not necessary in Linux I don't have any problem when mining on ethermine which this lunch line but on 2miners I have the error which I have mentioned
|
|
|
|
alizali
Newbie
Offline
Activity: 197
Merit: 0
|
|
March 18, 2021, 04:13:11 PM |
|
hi guys i have RX470 4GB Sapphire (Elpida EDW4032BABG · 113-7E353FU-M78) os: hiveos OC: core1126 with 800~810MV memory:1900 miner: teamredminer coin: RVN i got 13.5 MH for GPU with 57C with fan 50~60% with 80-85 watt report on hiveos (if i increase memory to 1975 i have 14.5 for each card but temperature goes up and not idle for me)
any suggestion for better hash with lower temperature?
thanks for your great opinion
|
|
|
|
Littlegrand
Jr. Member
Offline
Activity: 104
Merit: 5
|
|
March 19, 2021, 01:59:44 PM |
|
What is a good hashrate from TRM on haven with a RX570 4gb?
I am getting around 900h/s. Trying to tweak but not much seems to make a difference...
|
|
|
|
|
Akyboy
Jr. Member
Offline
Activity: 90
Merit: 1
|
|
March 20, 2021, 04:45:10 PM |
|
Hi Guys
Is there way to setup this miner to overclock rx580 similar to phoenix miner ( -gt 68 -cclock 1130 -mclock 2200 -cvddc 850 -mvddc 850 ) I have tried adding this line but it doesn't work
|
|
|
|
nik-qz
|
|
March 20, 2021, 09:01:28 PM |
|
Hi Guys
Is there way to setup this miner to overclock rx580 similar to phoenix miner ( -gt 68 -cclock 1130 -mclock 2200 -cvddc 850 -mvddc 850 ) I have tried adding this line but it doesn't work
see here for an example of the required programs and commands, if i'm not mistaken, the analogue of the -gt parameter, in TRM it is --eth_config=A which is selected by itself https://bitcointalk.org/index.php?topic=5059817.msg56418010#msg56418010
|
|
|
|
slklylnlelt
Newbie
Offline
Activity: 3
Merit: 0
|
|
March 21, 2021, 05:14:38 AM |
|
To get into B mode when mining ravencoin, would you still put --eth_config=B or would it change to something else.
|
|
|
|
buraz11
Jr. Member
Offline
Activity: 115
Merit: 4
|
|
March 22, 2021, 05:46:22 AM |
|
I have a problem getting the trm to mine nimiq in hiveos i keep getting this message when connecting to pools Pool us.nimpool.io (PROXY) connection was closed by the pool.
|
|
|
|
weifa
Sr. Member
Offline
Activity: 776
Merit: 308
GeoCoin Developer - GIS Technologist
|
|
March 26, 2021, 05:02:36 AM |
|
I see Etchash support was recently added in version 0.7.18. Just wondering if there is potential to add Ubqhash support to a future release? Ubqhash is another Ethash variant so should be similar process. Here's some of the technical info: https://blog.ubiqsmart.com/introducing-ubqhash-8fa515befd7Would adding Ubqhash to TRM be possible?
|
|
|
|
Haik
Newbie
Offline
Activity: 46
Merit: 0
|
|
March 28, 2021, 08:33:46 AM |
|
How to config this miner to mine rvn plus zil?
|
|
|
|
miner29
|
|
March 28, 2021, 01:07:39 PM |
|
Hi guys
I'm getting a weird error when mining ravencoin (kawpow)
So after a few hours the miner crashes (but gpu doesn't crash)
Error messages from log:
GPU 0 ERROR - failed to allocate ethash dag buffer GPU 0 thread exiting with error. Watchdog detected all worker threads have exited, shutting down. Shutting down... Watchdog thread exiting. Successful clean shutdown.
Why am I getting ethash dag buffer error if mining kawpow?
This happens with both an rx 570 4GB, and rx 470 4GB card in separate rigs
My bat tile is the standard .bat found with my wallet and pool added plus the logging option
Not sure how to resolve this? Please advise
Thanks
Make sure your config has --algo kawpow
|
|
|
|
doncoyote
Newbie
Offline
Activity: 18
Merit: 1
|
|
March 29, 2021, 04:06:39 PM |
|
Hi all,
Any recommended command line to use in TRM to mine ETH with a RX6800?
Much appreciated!
|
|
|
|
grandmabtc
Newbie
Offline
Activity: 4
Merit: 0
|
|
March 30, 2021, 05:10:53 AM |
|
I have a xfx 570 8gb (samsung memory), bios flashed, 1150 core clock - 2000 memory clock - 850 mv, most recent driver. Was expecting to get 30mhs, or at least 29, yet only getting around 27.82 https://i.imgur.com/FkrL74g.png. Does someone know what could be? Such as maybe my bios flash wasn't so optimal, or I'm not tweaking the miner the way I should (i'm not tweaking it all, it's running on auto-tune) Would appreciate suggestions.
|
|
|
|
|