treanski
Full Member
 Offline
Activity: 364
Merit: 106
ONe Social Network.
|
 |
January 24, 2018, 05:20:54 AM |
|
can you make option to disable the charts? they just use alot of cpu power
ggs is using 50% cpu power on cryptonight for me
|
|
|
|
|
|
|
|
|
|
|
I HATE TABLES I HATE TABLES I HA(╯°□°）╯︵ ┻━┻ TABLES I HATE TABLES I HATE TABLES
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
uhdog81
Newbie
Offline
Activity: 1
Merit: 0
|
|
January 24, 2018, 06:22:18 AM |
|
Not sure if anyone else has had issues with high DPI displays and GGS, but I couldn't see the checkboxes for selecting active GPUs when I updated from 1.2.2 to 1.2.7 (Win10, desktop resolution is 3840x2160). Changing the DPI scaling options in Properties fixed the table showing properly so I could actually activate the GPUs I wanted. Kinda obvious solution to try but just thought I'd throw it out there in case anyone ran into the same issue and wasn't sure. Screenshot for option to change: https://imgur.com/s7jOCa6 |
|
|
|
|
rusman2
Newbie
Offline
Activity: 21
Merit: 0
|
|
January 24, 2018, 06:59:27 AM |
|
Crash dump has the following. I am just pasting this, if you want the rest of it: https://pastebin.com/W4gHCndP. BugCheck 50, {fffffc7e00000000, 0, 0, 6}
Probably caused by : dxgkrnl.sys ( dxgkrnl!DXGADAPTERALLOCATION::~DXGADAPTERALLOCATION+1a )
0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced. This cannot be protected by try-except.
Typically the address is just plain bad or it is pointing at freed memory.
Arguments:
Arg1: fffffc7e00000000, memory referenced.
Arg2: 0000000000000000, value 0 = read operation, 1 = write operation.
Arg3: 0000000000000000, If non-zero, the instruction address which referenced the bad memory
address.
Arg4: 0000000000000006, (reserved)
|
|
|
|
|
|
UnclWish
|
|
January 24, 2018, 08:15:07 AM |
|
Crash dump has the following. I am just pasting this, if you want the rest of it: https://pastebin.com/W4gHCndP. BugCheck 50, {fffffc7e00000000, 0, 0, 6}
Probably caused by : dxgkrnl.sys ( dxgkrnl!DXGADAPTERALLOCATION::~DXGADAPTERALLOCATION+1a )
0: kd> !analyze -v
*******************************************************************************
* *
* Bugcheck Analysis *
* *
*******************************************************************************
PAGE_FAULT_IN_NONPAGED_AREA (50)
Invalid system memory was referenced. This cannot be protected by try-except.
Typically the address is just plain bad or it is pointing at freed memory.
Arguments:
Arg1: fffffc7e00000000, memory referenced.
Arg2: 0000000000000000, value 0 = read operation, 1 = write operation.
Arg3: 0000000000000000, If non-zero, the instruction address which referenced the bad memory
address.
Arg4: 0000000000000006, (reserved)
How much pagefile size is set on your system? Try to increase it to summary size of your videocards videomemory. Check drive where pagefile located on errors via My computer or chkdsk command. |
|
|
|
|
|
preda
|
|
January 24, 2018, 08:58:16 AM |
|
Ahh, well that was too soon. It crashed again. Windows page fault. I have scanned the drive and ran sfc /scannow and no errors.
Any thoughts on this? Is there a log I can pull info from or setup to help?
Edit:Where does this application even log to? I see nothing in the install dir.
Are you using the recommended driver (18.1.1) with CrossFire off? The log file is in %AppData%. i still use august blockchain drivers! i should switch to 18.1.1? |
|
|
|
|
|
UnclWish
|
|
January 24, 2018, 09:08:29 AM |
|
Ahh, well that was too soon. It crashed again. Windows page fault. I have scanned the drive and ran sfc /scannow and no errors.
Any thoughts on this? Is there a log I can pull info from or setup to help?
Edit:Where does this application even log to? I see nothing in the install dir.
Are you using the recommended driver (18.1.1) with CrossFire off? The log file is in %AppData%. i still use august blockchain drivers! i should switch to 18.1.1? If you didn't have Vega's then yes - you must change driver to 18.1.1. GGS is optimized for last drivers. |
|
|
|
|
|
preda
|
|
January 24, 2018, 09:09:53 AM |
|
Ahh, well that was too soon. It crashed again. Windows page fault. I have scanned the drive and ran sfc /scannow and no errors.
Any thoughts on this? Is there a log I can pull info from or setup to help?
Edit:Where does this application even log to? I see nothing in the install dir.
Are you using the recommended driver (18.1.1) with CrossFire off? The log file is in %AppData%. i still use august blockchain drivers! i should switch to 18.1.1? If you didn't have Vega's then yes - you must change driver to 18.1.1. GGS is optimized for last drivers. i do 29mh on my rx 570 4gb itx pulse i cant do more than that i guess |
|
|
|
|
zloy_hulk
Newbie
Offline
Activity: 40
Merit: 0
|
|
January 24, 2018, 09:11:32 AM |
|
https://imgur.com/a/HVI8hThat's my graphic and cpu usage - over 60%. When I use default settings (i=1, worksize=64), I have more troubles with hashrate drop, but less freezes. I'm waiting for improvements. Like this miner, but don't like strange drops and freezes.
|
|
|
|
|
|
UnclWish
|
|
January 24, 2018, 11:38:27 AM |
|
Ahh, well that was too soon. It crashed again. Windows page fault. I have scanned the drive and ran sfc /scannow and no errors.
Any thoughts on this? Is there a log I can pull info from or setup to help?
Edit:Where does this application even log to? I see nothing in the install dir.
Are you using the recommended driver (18.1.1) with CrossFire off? The log file is in %AppData%. i still use august blockchain drivers! i should switch to 18.1.1? If you didn't have Vega's then yes - you must change driver to 18.1.1. GGS is optimized for last drivers. i do 29mh on my rx 570 4gb itx pulse i cant do more than that i guess In case of stability and compatibility it's best to update. But if on your system GGS works fine with your current driver, you can leave it. |
|
|
|
|
oldman8
Newbie
Offline
Activity: 4
Merit: 0
|
|
January 24, 2018, 01:06:06 PM |
|
I used GGS to mined for ETN without issue.
But when i tried to use it for ETH, it kept giving me the below message.
"
2018-01-24 20:57:23.6394 [1] Failed to update pool statistics.
2018-01-24 20:57:24.1227 [1] Failed to update pool statistics.
2018-01-24 20:57:25.1188 [1] Failed to update pool statistics.
"
Is this normal?
|
|
|
|
|
Loosecheck
Newbie
Offline
Activity: 106
Merit: 0
|
|
January 24, 2018, 01:08:16 PM |
|
The addition of new algorithms will be? what kind?
|
|
|
|
|
Larvitar
Jr. Member
Offline
Activity: 196
Merit: 1
|
|
January 24, 2018, 02:19:12 PM |
|
Hi! Is there Linux binaries for GatelessGate? I'm trying to test it in HiveOS  |
|
|
|
|
coke15
Member
Offline
Activity: 176
Merit: 10
|
|
January 24, 2018, 02:26:25 PM |
|
The addition of new algorithms will be? what kind?
equihash will be great i have a "bug" in 1.2.7,with 2 570 i loose 150h/s compared to 1.2.2. ? |
|
|
|
|
|
|
treanski
Full Member
Offline
Activity: 364
Merit: 106
ONe Social Network.
|
|
January 24, 2018, 09:03:15 PM |
|
fired it up 30minutes ago  yeah im stalking your github... seems to be running very smooth, no lags, no delays..lets see how it will perform in a long run. now you just need to make it fast for vega like with blockchain driver   |
|
|
|
rusman2
Newbie
Offline
Activity: 21
Merit: 0
|
|
January 24, 2018, 09:22:37 PM |
|
I found that a Windows patch updated the DXGKRNL file, but I was having crashes before this update. I uninstalled that update and will also try newest miner version to see if that helps.
|
|
|
|
|
|
UnclWish
|
|
January 24, 2018, 09:39:40 PM
Last edit: January 24, 2018, 10:38:08 PM by UnclWish |
|
Please, update source code on github... EDIT: Don't seen any surprise... CPU usage grows with time as in previous version... |
|
|
|
|
rusman2
Newbie
Offline
Activity: 21
Merit: 0
|
|
January 24, 2018, 11:20:03 PM |
|
How much pagefile size is set on your system? Try to increase it to summary size of your videocards videomemory.
Check drive where pagefile located on errors via My computer or chkdsk command.
I didn't see your post earlier and just checked - pagefile is at 24G, which was recommended and set by GGS when I installed it about a week ago. I have 2 cards at 4G each so this is more than enough based on your recommendation to match the size of the video cards. I checked RAM and disk for errors overnight and no issues with either one. |
|
|
|
|
|
UnclWish
|
|
January 24, 2018, 11:50:52 PM
Last edit: January 25, 2018, 12:02:46 AM by UnclWish |
|
How much pagefile size is set on your system? Try to increase it to summary size of your videocards videomemory.
Check drive where pagefile located on errors via My computer or chkdsk command.
I didn't see your post earlier and just checked - pagefile is at 24G, which was recommended and set by GGS when I installed it about a week ago. I have 2 cards at 4G each so this is more than enough based on your recommendation to match the size of the video cards. I checked RAM and disk for errors overnight and no issues with either one. Did you tried last GGS version? Bug is still here? Try to remove overclocking and undervoltage. Return default vbios. Try to disable overclock option in GGS settings. Check your PSU. |
|
|
|
|
rusman2
Newbie
Offline
Activity: 21
Merit: 0
|
|
January 25, 2018, 12:28:31 AM |
|
I did just update to the one updated today. It just crashed again but this time I noticed some weird behavior, like Chrome would open after a 30s delay or web pages would also take a long time to open/connect. I then stopped the miner and was going to reboot, but when I hit the X to close GGS, it blue screened...again. This time it gave a different DXG file as the culprit so it at least doesn't like DirectX 12. Something else is going on so I might just do a windows repair or do a complete reinstall. I've had too many crashes and now weird behavior so I think it needs a rebuild.
I didn't think that DirectX was involved in mining. I'd be happy to learn otherwise.
|
|
|
|
|
|
Poll
