Fourth alt coin thread last three got oversized.

[fr4nkthetank]

Keep in mind the big 200mm fans - although the CFM is nice - dont push as much air where you want it vs a smaller fan.  if you are pulling air, then I guess it should be good but I prefer when you can actually feel the airflow.  On another note I just bought a vortex s-800 fan to extract hot air out of my garage, if you guys are interested ill let you know how it works out.  It was on sale and I need to keep the noise down.  i'll probably build a box around it anyway.

[citronick]

Keep in mind the big 200mm fans - although the CFM is nice - dont push as much air where you want it vs a smaller fan.  if you are pulling air, then I guess it should be good but I prefer when you can actually feel the airflow.  On another note I just bought a vortex s-800 fan to extract hot air out of my garage, if you guys are interested ill let you know how it works out.  It was on sale and I need to keep the noise down.  i'll probably build a box around it anyway.

hey frank - can you send pix of you solution when completed -- I have a similar idea to build some sort of a housing for the 200mm fan to be effective. thanks

Btw, is there a "hang-out-of-window" type blower/fan/exhaust/extractor ?

My warehouse lease doesnt allow me to do any permanent fittings, I have to find a way to increase the airflow out from the warehouse.

I currently have this - see pix below - useful because I can position the other end of that duct to hotspots in the warehouse... however I need to find a overall blower solution to work in tandem with this current blower.

[Storx]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

Im still learning, but i was told if you go with 2 PSU's on a rig you have to power the risers from the psu connected to the mobo otherwise the 2nd psu will backfeed through the riser and cause power conflicts and unstable rig... but powering the GPU's directly from a 2nd psu to the 6/6+2 plugs on the GPU doesnt cause any issues...

Im still waiting on some parts for my first riser build.. but one person told me its worth buying connectors that fit whichever psu you use to power the mobo and hard wire the riser to the psu cable directly by soldering the wires to the 4 pins.... was told this is the safest way to go with the molex style risers... or build my own cables from scratch entirely going with oversized wires...

[ticmmae]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

[philipma1957]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

when they are correctly built the answer is yes  hawkfish007 sells them send him  a pm.

[citronick]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

its like a Y cable (one for GPU and one for riser) .... one single cable that goes back to server PSU

look closely here.... one cable splits into 2 pci connector, an 8pin for GPU and 6pin for riser... this way power goes to both devices at the same time so consistency perhaps makes a stable rig....

[NOLA]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

[citronick]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

2.7 efficiency is usually stock ..... you really should do something about the watts 293w is really bad... waste of energy

Phils has good guides to finetune 1080tis to get low power but good hash ratio, and achieve 3-ish efficiency

my 4 x Aorus 1080ti as follows
nvOC Linux, 165/0/195

[Storx]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

its like a Y cable (one for GPU and one for riser) .... one single cable that goes back to server PSU

look closely here.... one cable splits into 2 pci connector, an 8pin for GPU and 6pin for riser... this way power goes to both devices at the same time so consistency perhaps makes a stable rig....

who sells those Y cables you talk about.. also how long are those usb cables your using?

[NOLA]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

2.7 efficiency is usually stock ..... you really should do something about the watts 293w is really bad... waste of energy

Phils has good guides to finetune 1080tis to get low power but good hash ratio, and achieve 3-ish efficiency

The settings are the ones I saw him post but ill double check them

I will look into the power consumption,  will need to get it handled before adding another few cards and setups.

[citronick]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

2.7 efficiency is usually stock ..... you really should do something about the watts 293w is really bad... waste of energy

Phils has good guides to finetune 1080tis to get low power but good hash ratio, and achieve 3-ish efficiency

The settings are the ones I saw him post but ill double check them

I will look into the power consumption,  will need to get it handled before adding another few cards and setups.

I use settings

165 core, 0 mem, PL 195

I still get good hash of 650ish but cards are cool and stable

[kopija]

who sells those Y cables you talk about.. also how long are those usb cables your using?

Alibaba has you covered:
https://www.aliexpress.com/item/Graphics-card-8pin-to-dual-8pin-6-2-power-cable-made-of-18AWG-wire-for-BTC/1649864219.html

[ticmmae]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

its like a Y cable (one for GPU and one for riser) .... one single cable that goes back to server PSU

look closely here.... one cable splits into 2 pci connector, an 8pin for GPU and 6pin for riser... this way power goes to both devices at the same time so consistency perhaps makes a stable rig....

https://i.imgur.com/N8xo4v6.png?1

Is the cable something like this? http://i.ebayimg.com/images/g/3gkAAOSwiQ9ZPZn6/s-l1600.jpg

6 pin female goes to PSU then 6+2pin male to your GPU and 6 pin male to riser. is it okay to leave 2 pin unconnected and just connect 6 pin tho?

[citronick]

who sells those Y cables you talk about.. also how long are those usb cables your using?

Alibaba has you covered:
https://www.aliexpress.com/item/Graphics-card-8pin-to-dual-8pin-6-2-power-cable-made-of-18AWG-wire-for-BTC/1649864219.html

more like this:

https://www.aliexpress.com/item/Modular-PSU-Power-Supply-Cables-PCI-e-Molex-6pin-to-2-PCI-e-8-pin-6/32813533682.html?spm=2114.10010108.1000015.1.iZpOe1&s=p

but mine is custom made for length -- I get them from yslyung

[citronick]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

its like a Y cable (one for GPU and one for riser) .... one single cable that goes back to server PSU

look closely here.... one cable splits into 2 pci connector, an 8pin for GPU and 6pin for riser... this way power goes to both devices at the same time so consistency perhaps makes a stable rig....

Is the cable something like this? http://i.ebayimg.com/images/g/3gkAAOSwiQ9ZPZn6/s-l1600.jpg

6 pin female goes to PSU then 6+2pin male to your GPU and 6 pin male to riser. is it okay to leave 2 pin unconnected and just connect 6 pin tho?

if you are using ATX PSU, you need 8 pins but if server psu the breakout boards are usually 6pin

leaving the 2 pin out is fine -- quite flexible these 6+2 connectors

[philipma1957]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

2.7 efficiency is usually stock ..... you really should do something about the watts 293w is really bad... waste of energy

Phils has good guides to finetune 1080tis to get low power but good hash ratio, and achieve 3-ish efficiency

The settings are the ones I saw him post but ill double check them

I will look into the power consumption,  will need to get it handled before adding another few cards and setups.

Do you have --pec. At the end of the bat file in ewbf_ 3.4 or 3.3?  It will show you power at the card.

Your number is power at the wall or some how the tdp is not at 70%

[ticmmae]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

its like a Y cable (one for GPU and one for riser) .... one single cable that goes back to server PSU

look closely here.... one cable splits into 2 pci connector, an 8pin for GPU and 6pin for riser... this way power goes to both devices at the same time so consistency perhaps makes a stable rig....

https://i.imgur.com/N8xo4v6.png?1

Is the cable something like this? http://i.ebayimg.com/images/g/3gkAAOSwiQ9ZPZn6/s-l1600.jpg

6 pin female goes to PSU then 6+2pin male to your GPU and 6 pin male to riser. is it okay to leave 2 pin unconnected and just connect 6 pin tho?

if you are using ATX PSU, you need 8 pins but if server psu the breakout boards are usually 6pin

leaving the 2 pin out is fine -- quite flexible these 6+2 connectors

I never thought of connecting it this way. Most people's setup has separate cables powering risers and GPUs. This is not a bad idea as you explained the reason. so 8 pins to two 6+2pins cable would work same way? Thank you for the enlightment.

[EvilMonkey]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

Pretty sure those settings are for mining SKEIN.  For zec it is different.

You actually want to boost the memory.  This is my settings on my Auros Card which already has high rates already so you can't over clock it as hard.
TDP = 75
+75 core
+375 Memory
+75 fan (but this depends where you live and how cold it is.  I use +50 fan as its cold as heck here right now).

Those setting should work well for you on non Aorus card.  But you can likely get more out of the core and memory.  If you are already geting 250 and its not freezing then you can probably do that. You can likely inch your memory upto 450.   But 400 is prolly semi safe.  The issue is your memory.  Zec mining is effected by it SKEIN is not really.

[philipma1957]

It's official....have my first miner up and running.

Didn't install all 3 GPUs, made sure I didn't blow up the first one first.

Have one 1080ti FE going to Nicehash w EWBF 0.3.4b

I will learn how to put in pictures later, not sure if I even can right now.

Pushing 700 sol @ 293W at the Kill-A-Meter.  276 sol/W efficiency ( seems low compared to others).

GPU @ 72C

Have settings set on Afterburner---70 TDP, 73C temp limit, +250 Core, -500 Memory, Fan 75%

Appreciate everyone's thoughts and ideas in general.

Time to buy 500 more 1080ti's.
---------------
The 2.76 sol/W.....seems a little low, anything I can do to change that?

Pretty sure those settings are for mining SKEIN.  For zec it is different.

You actually want to boost the memory.  This is my settings on my Auros Card which already has high rates already so you can't over clock it as hard.
TDP = 75
+75 core
+375 Memory
+75 fan (but this depends where you live and how cold it is.  I use +50 fan as its cold as heck here right now).

Those setting should work well for you on non Aorus card.  But you can likely get more out of the core and memory.  If you are already geting 250 and its not freezing then you can probably do that. You can likely inch your memory upto 450.   But 400 is prolly semi safe.  The issue is your memory.  Zec mining is effected by it SKEIN is not really.

Your info is wrong.  Skein and Zec both like high core low memory.

Eth like high ram

[citronick]

can you guys recommend which type of risers I should use? Getting mixed opinions everywhere. I was gonna go with sata risers directly to 6 pins but heard it is dangerous. What is the safest way to power risers?

I personally prefer PCIE 6pin type (riser version 6?) so that I can reuse my 6pin PCIE cables especially when using server PSU.

I have many SATA powered risers in production now and all ok so far.

I guess its a matter of good quality build instead of "dangerous", and if your SATA cable connects via molex onto the riser -- ensure that its tight and secured. I suspect that the real danger is when low quality molex doesn't get in proper contact or loosely contact with the 4 pins -- thats where trouble starts... ie. sparks, fire hazard, damaged riser eventually over time.

For risers I usually take good look on the quality of the USB3 cable... the ones that are "fat" or shielded likely have 100% uptime compared to the flimsy ... phone charger looking type USB cables...

so with PCIE 6 pin risers, you go 6 pin to 6 pin cable directly without using any adaptor?

its like a Y cable (one for GPU and one for riser) .... one single cable that goes back to server PSU

look closely here.... one cable splits into 2 pci connector, an 8pin for GPU and 6pin for riser... this way power goes to both devices at the same time so consistency perhaps makes a stable rig....

Is the cable something like this? http://i.ebayimg.com/images/g/3gkAAOSwiQ9ZPZn6/s-l1600.jpg

6 pin female goes to PSU then 6+2pin male to your GPU and 6 pin male to riser. is it okay to leave 2 pin unconnected and just connect 6 pin tho?

if you are using ATX PSU, you need 8 pins but if server psu the breakout boards are usually 6pin

leaving the 2 pin out is fine -- quite flexible these 6+2 connectors

I never thought of connecting it this way. Most people's setup has separate cables powering risers and GPUs. This is not a bad idea as you explained the reason. so 8 pins to two 6+2pins cable would work same way? Thank you for the enlightment.

there many types of risers, so many possibilities as per what config you have or want, and what PSU you are using.