AMD Releases Driver for DAG Issue !!!

[kiaas]

As far as i know this driver does not work on Win 7.

It does work on Win 10 for RX580's. Just dont patch the driver with pixel patcher on 580's.
I used AB 4.4.0 Beta 16, works for OC settings. It however does not seem to undervolt card.
Also do not set your OC settings in the Claymore Batch file. does not work. The Driver changed the ADL API so would need an update for Claymore to fix this.
I used Global Wattman that comes with driver. Manually setting Voltage to 990mV and apply, it applies it but sometimes just reverts back to higher voltage later. Just set it back to Auto and apply then my voltage goes to 990mV again. (i do this while claymore is running)
Not even AMD software is properly controlling the Voltage..... tisk tisk AMD!
When you apply the pixel patcher and OC from the claymore batch file you get your mem clock jumping between 2150 and 1000MHz the whole time.
EVen GPU-z is reading GPU load incorrectly at 16% and mem controller 100% when it should be idle. HWinfo64 seems to read the GPU load correctly.

Managed to get my card stable at 30.5MH/s (MSI RX580 Armor 8GB) 990mV, 1250 GPU core, 2150 Mem clocks. Drawing under 100W running at 59-61C Temps. Happy will settle for that.
If running other AMD cards in the machine, and settings dont apply to others it could be because the are running headless. Might need to plug in a dummy plug into cards to make it think it has monitor connected. i know this works. Have found this with Nvidia mixed with AMD machines.
All Nvidia no problem.

AMD wont update driver again, so Claymore will hopefully soon update to fix OC and undervolt issues directly from the Miner batch file.

I was just coming here to see why all my mining software just immediately crashed with it, since it is available for and installing on win7 fine, among other things that had my hopes up that there'd be something I could do to fix it. Oh well. :/

[1714139306]

1714139306

[panosarp]

The official AMD blockchain driver for windows 7 x64 does not work (miners crash).
The leaked driver from robinh00d works but nothing can undervolt my RX570's, only OverdriveNTool  works for a few seconds before reverting.

The solution that worked best is to use the leaked driver and the wattman from the official driver:

1.  Install the official amd driver with amd settings
2.  Without reboot install the leaked driver via device manager by going the "i have a disk" route (for all cards - one by one)
3.  If you have a modified bios, run atikmdag-patcher and reboot 
4.   Use wattman to apply your mem clock and volt settings
5. Open miner, everything will be ok except undervolt, now with miner running make a small change to wattman and reapply (for each card one by one)

The voltages appear to be sticking for as long as the miner is running , except for the main card that reverts occasionally.
 

[QuintLeo]

Tryid it on 280x
Got 12-13mh per one(8.1x64, cm9....nothing change from 15.12 driver. Stupid amd didn't applied their fix to truly good cards

 It didn't change because the R9 280x didn't suffer from the issue that the driver was intended to fix.
 The 280x was never a "truely good" ETH card in the first place - that was the 290 and to a lesser degree the 290x.

 Tahiti is arguably the best performance/price ratio for FP64 anyone ever released, but ETH doesn't use floating point....

[QuintLeo]

What is wrong with using free windows 10?

 Why should I have to completely reinstall an OS from scratch on all my machines to run an OS I despise for it's built-in spyware issues and VERY POOR stability instead of sticking with my RELIABLE LINUX OS setup?

 Oh yeah, did I forget to mention "far easier to clone when building a NEW machine" using built-in LINUX "DD" command vs being forced to reinstall from scratch to do a "free" Win10 installation on a new machine?

 VERY FEW MINING RIGS RUN WINDOWS AT ALL - there are REASONS for that, and they ALL apply to bloody Windows 10.

[P00P135]

What is wrong with using free windows 10?

 Why should I have to completely reinstall an OS from scratch on all my machines to run an OS I despise for it's built-in spyware issues and VERY POOR stability instead of sticking with my RELIABLE LINUX OS setup?

 Oh yeah, did I forget to mention "far easier to clone when building a NEW machine" using built-in LINUX "DD" command vs being forced to reinstall from scratch to do a "free" Win10 installation on a new machine?

 VERY FEW MINING RIGS RUN WINDOWS AT ALL - there are REASONS for that, and they ALL apply to bloody Windows 10.

Not sure why you are so angry lmao.  I was talking to the guy running windows 7 with a lot of issues. 

[antiycda]

The official AMD blockchain driver for windows 7 x64 does not work (miners crash).
The leaked driver from robinh00d works but nothing can undervolt my RX570's, only OverdriveNTool  works for a few seconds before reverting.

The solution that worked best is to use the leaked driver and the wattman from the official driver:

1.  Install the official amd driver with amd settings
2.  Without reboot install the leaked driver via device manager by going the "i have a disk" route (for all cards - one by one)
3.  If you have a modified bios, run atikmdag-patcher and reboot 
4.   Use wattman to apply your mem clock and volt settings
5. Open miner, everything will be ok except undervolt, now with miner running make a small change to wattman and reapply (for each card one by one)

The voltages appear to be sticking for as long as the miner is running , except for the main card that reverts occasionally.
 

everything is works now. except the power with eth+SC almost sucks 140W.

[Mattthev]

Why should I have to completely reinstall an OS from scratch on all my machines to run an OS I despise for it's built-in spyware issues and VERY POOR stability instead of sticking with my RELIABLE LINUX OS setup?

 Oh yeah, did I forget to mention "far easier to clone when building a NEW machine" using built-in LINUX "DD" command vs being forced to reinstall from scratch to do a "free" Win10 installation on a new machine?

 VERY FEW MINING RIGS RUN WINDOWS AT ALL - there are REASONS for that, and they ALL apply to bloody Windows 10.

Very few? About 80% guys who contacts me are running Windows... most of them 10 but some of them 7.

[nars28]

Beta Blockchain driver doesn't work for me. Miner crashes. So i installed latest non Beta driver on my rx570. i'm mining signatum so don't need the DAG solved driver 

[Chipychop]

@antycda and how much power consumption before these drivers?

I'd like to put a question for owners of rx 570 4gb. anyone has tested beta drivers on higher DAG epoch like #180?

I doubt wether mount 2 rx 570 rigs or one with gtx 1070

because rx 570 are 4gb model and maybe in future it will be too low to mine anything...

any idea?

[spyshagg]

Power to hash ratio is more important right now.  I'm staying with the old driver until this driver works and undervolts as expected.

[adaseb]

Tryid it on 280x
Got 12-13mh per one(8.1x64, cm9....nothing change from 15.12 driver. Stupid amd didn't applied their fix to truly good cards

 It didn't change because the R9 280x didn't suffer from the issue that the driver was intended to fix.
 The 280x was never a "truely good" ETH card in the first place - that was the 290 and to a lesser degree the 290x.

 Tahiti is arguably the best performance/price ratio for FP64 anyone ever released, but ETH doesn't use floating point....

The 7970/280x was actually very good at ETH only at the beginning. With DaggerCoins at Epoch #0 or #1 or so it can get like 28MH/s. And a year ago you could of found them on Craigslist for $100 second hand. The R9 290 while it was a little faster was always expensive to buy because it had high demand for gamers and was hard to find for less than $200. So the 280x was a better choice if it wasn't for the DAG bug.

[RentGPU]

Did it worked with win 7 , any confirmations?!

[vapourminer]

Did it worked with win 7 , any confirmations?!

no.

on win7 either blank screen or if you get far enough claymore 9.8 exits at pool prompt.

[w0lf0.]

Very bad for me, power consption is too important and that driver is bad for it, i remain with my old driver

[anders31]

installed win 10 now my hash increased from 27 eth + 800 decred to 29eth + 890 decred but the power went higher and yea dag size is fixed

[mini miner]

Rx570 @  27,2 mh/s ETH and 707 mh/s DCR with dcri 26 and claymore 9.8 dual mining.

can you explain about any changes in  r7 370 with this driver

[Chipychop]

I'd like to ask owners of rx 570 4gb. anyone has tested beta drivers on higher DAG epoch like #180?

I doubt wether mount 2 rx 570 rigs or one with gtx 1070

because rx 570 are 4gb model and maybe in future it will be too low to mine anything...

which would be your recommendation?

thanks in advance

[Vann]

I'd like to ask owners of rx 570 4gb. anyone has tested beta drivers on higher DAG epoch like #180?

I doubt wether mount 2 rx 570 rigs or one with gtx 1070

because rx 570 are 4gb model and maybe in future it will be too low to mine anything...

which would be your recommendation?

thanks in advance

https://bitcointalk.org/index.php?topic=2092279.msg20905036#msg20905036

The Dag size is not an issue for 4GB cards. Even 3GB cards will be OK until November 2018 and the Dag size won't reach 4GB until something like 2020. ETH will move to POS long before that.

[panosarp]

The official AMD blockchain driver for windows 7 x64 does not work (miners crash).
The leaked driver from robinh00d works but nothing can undervolt my RX570's, only OverdriveNTool  works for a few seconds before reverting.

The solution that worked best is to use the leaked driver and the wattman from the official driver:

1.  Install the official amd driver with amd settings
2.  Without reboot install the leaked driver via device manager by going the "i have a disk" route (for all cards - one by one)
3.  If you have a modified bios, run atikmdag-patcher and reboot 
4.   Use wattman to apply your mem clock and volt settings
5. Open miner, everything will be ok except undervolt, now with miner running make a small change to wattman and reapply (for each card one by one)

The voltages appear to be sticking for as long as the miner is running , except for the main card that reverts occasionally.
 

everything is works now. except the power with eth+SC almost sucks 140W.

Using OverdriveNTool from here: https://forums.guru3d.com/threads/overdriventool-tool-for-amd-polaris-gpus.416116
you can disable all power states except P7 for gpu and P2 for memory, that way the undervolt will be retained since gpu will always be at the highest performance state
and never throttle down.
The cards will consume more power when idle that way but for a mining ring that is irrelevant. 

[Mattthev]

https://bitcointalk.org/index.php?topic=2092279.msg20905036#msg20905036

The Dag size is not an issue for 4GB cards. Even 3GB cards will be OK until November 2018 and the Dag size won't reach 4GB until something like 2020. ETH will move to POS long before that.

Only Dual mining is problem with 3GB.