[ANN] US/North American Bitfury sales NEW STOCK ***NOW SHIPPING***

[aspeer]

or pickup a $3 PSU tester... also dont't rely on colors rely on the pin out unless you want to find out what a cheap PSU looks like blown up... Remember you're messing with electricity when doing this and use common sense.

http://www.bittimania.fi/wp-content/uploads/2013/08/psu_cheat.png

or get

http://www.robotshop.com/productinfo.aspx?pc=RB-Cyt-101&lang=en-US

if you want to get fancy.

[Cablez]

or pickup a $3 PSU tester... also dont't rely on colors rely on the pin out unless you want to find out what a cheap PSU looks like blown up... Remember you're messing with electricity when doing this and use common sense.

Have you come across a PSU that did not use green for the PSON signal? Would be good to know.

[aspeer]

or pickup a $3 PSU tester... also dont't rely on colors rely on the pin out unless you want to find out what a cheap PSU looks like blown up... Remember you're messing with electricity when doing this and use common sense.

Have you come across a PSU that did not use green for the PSON signal? Would be good to know.

some cheapo's i've had were mis-colored, yes i hope you're using quality equipment but just a word of warning against assumptions on the color always being right.

[pixl8tr]

Anything wrong with H-Cards marked with green sticker?

I thought the green and red stickers are for orientation purposes on the M Board..  IE green sticker towards green sticker on the M board.  I had a red sticker on the back.
The Green sticker was on the side with the chips, the red sticker on the "bare" side of the H Board.

[dacman61]

Got my tracking number for order #10X.. Arriving Monday.

[-Redacted-]

Glad I ordered two starter kits. 

One of the two M-boards doesn't work.  No obvious solder bridges but lots of cold solder joints visible on the connector pins.  No juice to the RasPi.   The other M-board at least powers up the RasPi, so I'll use it.

[jspielberg]

Mine shows as delivered!!!

Edit:  Even while USPS showed delivery to another state... it was in fact delivered correctly.

[xstr8guy]

I have a tracking number for order 97.
order number 116 looks like it's still in 'paid' status.  I think 116 is the last august regular order. There are probably a few august refund orders after it.

/cet

I'm in the 130s for an August order and am still sitting at paid.

I bought the last starter kit for Aug and it's in the 2xx range - still showing as paid

I'm not sure how that's possible unless the order numbers aren't consecutive for some reason.  My October order from 7/11 (paid on 7/11 as well) is 19x.  Sure wish I had made the August order cutoff.

[EvilLizardApparel]

PSU ISSUE FIXED...now this...

Hey guys - I just got word that we sent out your rPi's configured with a weird gateway IP.  This is going to make it hard for your rigs to reach the outside world.

To fix this you'll need to connect direct to your rPi.  Either use keyboard/monitor, or use ssh to connect to it 192.168.1.249 (unless you changed IP).

Code:

sudo nano /etc/network/interfaces

use arrow keys to get down to

Code:

gateway 192.168.1.3

change this to

Code:

gateway 192.168.1.1

...or whatever your gateway IP is.

type

Code:

ctrl-X[enter]
Yes[enter]

reboot the rPi


Sorry for the trouble!

We're putting it on a public IP, and after setting the parameters in /etc/networking/interfaces, we get no IP address showing up when doing an ifconfig.  The address, netmask, and gateway are all correct in the file.  Is there ANYTHING that we can look at to see why the networking service isn't configuring the interface?

Any ideas?

[dracore]

Aww usps went to deliver but I was at work.  Went to post office to pick up but truck did not get back yet.  sigh... guess I won't be able to set it up tonight

[dacman61]

Aww usps went to deliver but I was at work.  Went to post office to pick up but truck did not get back yet.  sigh... guess I won't be able to set it up tonight

I would camp there until it arrived, and go to the desk every 20-30 minutes to ask "Is my package here yet?"

[EvilLizardApparel]

How long on your Bitfury admin page does it take for your hashrate to update? It is still at 0 GH/s, but chips are hot and the rPi states its mining...

[kaerf]

How long on your Bitfury admin page does it take for your hashrate to update? It is still at 0 GH/s, but chips are hot and the rPi states its mining...

One of my rigs needed several minutes to update to it's full hash rate.

[-Redacted-]

Took about 10 minutes to warm up, after I figured out that you don't use http:// in front of the pool URL, it even started to mine....


I'm a little short on one card, and over on the other....


Noncerate: 52.957GH/s

Bank 1
1: 29.478GH/s
2: 23.479GH/s

[kaerf]

Here are some pix from my unboxing  
http://imgur.com/a/7Q7M6

I got a bad h-card, so it took a while to figure out why one of the rigs wasn't working properly. dave has already said he will send a replacement. another example of awesome support from this team.

[dben428]

Order #89 shipped. 

Thanks again to Yvonne for catching my address mistake, verifying my correct address, and still shipping in a timely manner.

[demonmaestro]

We NEED pictures! 

[-Redacted-]

Here are some.  Having one heck of a time connecting to the forum.....

http://imgur.com/a/zFFV0#0

[goxed]

Wow! awesome news guys. Keep us updated with pics, esp boards that do not work to hep us debug once our stuff arrives.

 My USPS 2day priority status is on it's 3rd business day and no delivery.

[Morblias]

Wow! awesome news guys. Keep us updated with pics, esp boards that do not work to hep us debug once our stuff arrives.

 My USPS 2day priority status is on it's 3rd business day and no delivery.

lol you are not alone bro. if they don't come tomorrow i will be very upset. last tracking update it is still not even in my state yet.