[ANN] US/North American Bitfury sales NEW STOCK ***NOW SHIPPING***

[klondike_bar]

   What did you do to bring up voltage or were you changing resistors?

"Pencil mod".  I'm at work and can't remember the value though.  I do remember that it only took a *very* slight change in resistance to get the same voltage of my other cards.  If you tell me the value of your R02F resistor, I can tell you what resistance to shoot for.

i want to say that i moddd from 31->40GH by changing the resistance from ~1.7K to ~1.570K or something similar.

however, it can take a few hours for the resitor to heat up and bring down resistance=rising voltage=further heat, and when errors start kicking in or hashrate drops, just touch it with your finger and a miniscule amount of lead will come away, hopefully raising 0.010-0.030K(ohm) per touch. ive almost found it easier to tune backwards like this, since adding lead is a bit harder to fine-tune (+0.020 to -0.050K each time i attempt to add a miniscule amount of graphite)

go to an art store and get a 2B or softer pencil. 2HB lead is hard to work with, and using a 4B pencil is much easier

[Kaega]

So h-boards are back in stock with 250 count... where's the shipments?

[buzzdave]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

[klondike_bar]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

i have not yet gotten my store credit for august delay. push that through and i'll probably buy a board.

however, a price drop to $400 would be appropriate i think. $500 is fairly steep at this point

[Keefe]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

Orders placed now for H-cards will ship immediately? But I have not yet received shipment notification for an older order of H-cards (not with M-boards, so I've been assuming I'll get the old type). Is that order shipping immediately as well, as in today/tomorrow?

[buzzdave]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

Orders placed now for H-cards will ship immediately? But I have not yet received shipment notification for an older order of H-cards (not with M-boards, so I've been assuming I'll get the old type). Is that order shipping immediately as well, as in today/tomorrow?

Please contact Yvonne immediately - if you have an H-card order for V1/V2 M-boards, it should be out the door by now.  Sorry for the trouble.

[buzzdave]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

i have not yet gotten my store credit for august delay. push that through and i'll probably buy a board.

however, a price drop to $400 would be appropriate i think. $500 is fairly steep at this point

Sorry about that - I'll get it done in a minute.

[Keefe]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

Orders placed now for H-cards will ship immediately? But I have not yet received shipment notification for an older order of H-cards (not with M-boards, so I've been assuming I'll get the old type). Is that order shipping immediately as well, as in today/tomorrow?

Please contact Yvonne immediately - if you have an H-card order for V1/V2 M-boards, it should be out the door by now.  Sorry for the trouble.

I assume you mean sales@?

[buzzdave]

****3,000 chip BitFury Reels now in stock****

I've got a few cancelled reels that are now sitting, which is a shame.  You can buy these reels and get them immediately shipped with free expedited shipping for the pre-order price of $20/chip.

Cheers

[buzzdave]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

Orders placed now for H-cards will ship immediately? But I have not yet received shipment notification for an older order of H-cards (not with M-boards, so I've been assuming I'll get the old type). Is that order shipping immediately as well, as in today/tomorrow?

Please contact Yvonne immediately - if you have an H-card order for V1/V2 M-boards, it should be out the door by now.  Sorry for the trouble.

I assume you mean sales@?

Yep - sales@megabigpower.com, thanks

[tom99]

So h-boards are back in stock with 250 count... where's the shipments?

Wow, I literally hit Save about 30 seconds ago...yes I have a few extra H-cards of the old type that arrived.  Since I don't the M-boards for them, they are only useful for filling out your V1 or V2 M-boards.  Buy them now, and they will ship immediately.

Production is cranking for the next-gen boards, but I haven't received any shipping notifications yet.  I expect to see something in the next day or two...when product is on the way I'll give an update.

Orders placed now for H-cards will ship immediately? But I have not yet received shipment notification for an older order of H-cards (not with M-boards, so I've been assuming I'll get the old type). Is that order shipping immediately as well, as in today/tomorrow?

Please contact Yvonne immediately - if you have an H-card order for V1/V2 M-boards, it should be out the door by now.  Sorry for the trouble.

I assume you mean sales@?

Yep - sales@megabigpower.com, thanks

  Dave I just got 5hboards and hashed for about 20 minutes then short out my psu and I took out 5hboards.  I am running old V1 right.

[sveetsnelda]

  Dave I just got 5hboards and hashed for about 20 minutes then short out my psu and I took out 5hboards.  I am running old V1 right.

...ouch.  Are you sure they're all dead?

[davecoin]

Dave,

If we have orders for (an October starter kit and) H-Boards for October but there's no word on v3 M-Boards, can I just get a V2 M-board and my 9 extra H-cards shipped out tomorrow?  We are fast approaching the end of October.

Thanks,
Dave

[tom99]

  Dave I just got 5hboards and hashed for about 20 minutes then short out my psu and I took out 5hboards.  I am running old V1 right.

...ouch.  Are you sure they're all dead?

   no idea,  old v1 still ok but I am going to do test one by one to find out bad board.   I was lucky psu shut off and check all new v1 nothing burning.


ps: I am testing one of hboard got good hash about 28Gh/s and one miso-err:1 that bad or not anyone know?

[klondike_bar]

  Dave I just got 5hboards and hashed for about 20 minutes then short out my psu and I took out 5hboards.  I am running old V1 right.

...ouch.  Are you sure they're all dead?

   no idea,  old v1 still ok but I am going to do test one by one to find out bad board.   I was lucky psu shut off and check all new v1 nothing burning.


ps: I am testing one of hboard got good hash about 28Gh/s and one miso-err:1 that bad or not anyone know?

1-2 miso errors is okay per board.

[tom99]

  Dave I just got 5hboards and hashed for about 20 minutes then short out my psu and I took out 5hboards.  I am running old V1 right.

...ouch.  Are you sure they're all dead?

   no idea,  old v1 still ok but I am going to do test one by one to find out bad board.   I was lucky psu shut off and check all new v1 nothing burning.


ps: I am testing one of hboard got good hash about 28Gh/s and one miso-err:1 that bad or not anyone know?

1-2 miso errors is okay per board.

  Thank you , I try to check the soldering but my eyes bad maybe I need new glasses.

[Keefe]

One of the chips on an H-card received last week has been giving hundreds of miso errors per 5-min, and is giving no good results, but all other chips and cards, before and after in the chain, seem unaffected. Is there something I can do about it, or should I just write off that chip as bad and ignore it?

[klondike_bar]

whats the status on CC? I want to get another h-board using the store credit (still waiting on this - will it appear somewhere in my account?) and credit card to cover whatever difference remains

[klondike_bar]

One of the chips on an H-card received last week has been giving hundreds of miso errors per 5-min, and is giving no good results, but all other chips and cards, before and after in the chain, seem unaffected. Is there something I can do about it, or should I just write off that chip as bad and ignore it?

probably a bad chip. theres a few things you can try:

1) put the board as the last in your rig and/or try a different slot(s)
2) raise the voltage slightly. probably wont make a difference, but sometimes the chips seem to get themselves settled in with a little bit of heat/runtime. i had a chip go from <0.7GH for the first 2 days to being a totally normal operation after voltage tweaking.
3) look for any issues in the components and traces around the chip. (you likely wont see anything, but worth a try)
4) send it to me and ill test it in my system

[tom99]

whats the status on CC? I want to get another h-board using the store credit (still waiting on this - will it appear somewhere in my account?) and credit card to cover whatever difference remains

   I dont think CC is working yet.