[ANN][POOL] Mining Pool Hub - Multipool. Multialgo, Auto Exchange to any coin.

[Myth888]

Your welcome. btw additional info since it is pplns it wont switch until block is found. But yah awesome miner seems nice but i dont have that much rig and dont really wanna pay up front. Id rather donate 1% of my profits.hahaha

Yes, I am aware about PPLNS, it's a risk.
I will need some live tests.  :-)

hahaha let me know how it goes. im interested in your results. been to busy to play profit switch. maybe this dec ill finally get it back up again.

[1715228117]

1715228117

[1715228117]

1715228117

[SuperDerpBro]

Will that effect other algos? Excavator is the tops for some (None ETH) right now.

Any of the files in the folder called 'miners' can be edited/removed.

Yes, but excavator3 is the best one for other alorythms (And works fine for them) :/

Anyways, i tried it and the other ones worked fine. Until ExcavatorNvidia3.. take that out as well? What is the diff between 2 and 3?

[OdinYggd]

I am mining vertcoin and i have 31 mh/s but on website it shows 15mh/s and highest it shows 26mh/s.
I am not submitting any bad share so why does it not show actual hashrate? Also vertcoin mining takes long time to show any info. Anyone can help?

I had this problem with older versions of ccminer. I recently switched to v2.2.3.

https://github.com/tpruvot/ccminer/releases

The program reports a lower hashrate than other versions of ccminer, but the pool reports a much higher one. Keep in mind pool reported hashrate varies and can take a long time to show changes. But with the newer miner it actually reports the correct hashrate once in awhile. Not always half or less.

I'm observing reported hashrates significantly below miner values even with tpruvot ccminer 2.2.3. Usually it will show around 25Mh/s in worker stats for 28MH/s working, but at times it will report lower values.

The dashboard gauge seems to have a lot of averaging going on, because when I looked at it a few hours ago it only said 2 MH/s but some time later had corrected itself up to 24 MH/s.



As for being able to customize the auto switching a little to factor in things like capabilities and power consumption, that would be an amazing feature. Depending on what language it is in, I'd be willing to help make it happen.

[Gongolo]

Yes, but excavator3 is the best one for other alorythms (And works fine for them) :/

Anyways, i tried it and the other ones worked fine. Until ExcavatorNvidia3.. take that out as well? What is the diff between 2 and 3?

Where can I find Excavator?
Does it work with any pool or is it nicehash hardcoded?

[aaronsace]

Yes, but excavator3 is the best one for other alorythms (And works fine for them) :/

Anyways, i tried it and the other ones worked fine. Until ExcavatorNvidia3.. take that out as well? What is the diff between 2 and 3?

Where can I find Excavator?
Does it work with any pool or is it nicehash hardcoded?

MiningPoolHub is blocked by default but MultiPoolMiner bypasses the block:
https://github.com/aaronsace/MultiPoolMiner/releases

[MHB]

2. On the Zcoin Dashboard, I can see the Recent Credits for the past few days.
On 2017-12-08 it was noticeably lower, at about 1020AM UTC, I stopped receiving shares. At about 1220PM I received the email "no shares from worker in 10min". I logged in via TV and it was running as expected. But the shares only resumed at about 0930PM UTC.

How can I debug this? My Monero miner was still going strong, so it cannot be the network connection.

I think this was a pool issue last night, since my 24h profitability is about half of what I was expecting. There were some website issues last night, and a database issue as well that resulted in shares not being credited.

Lets see if it continues happening, or if the pool operator finds and fixes an issue.
...

I closed my miner 10 mins ago. The zcoin dashboard went from 800h/s to 1.1kH/s.....  "Hashrate based on shares submitted in the past 5 minutes." Im not sure what's going on here. These stats make no sense...

[Myth888]

2. On the Zcoin Dashboard, I can see the Recent Credits for the past few days.
On 2017-12-08 it was noticeably lower, at about 1020AM UTC, I stopped receiving shares. At about 1220PM I received the email "no shares from worker in 10min". I logged in via TV and it was running as expected. But the shares only resumed at about 0930PM UTC.

How can I debug this? My Monero miner was still going strong, so it cannot be the network connection.

I think this was a pool issue last night, since my 24h profitability is about half of what I was expecting. There were some website issues last night, and a database issue as well that resulted in shares not being credited.

Lets see if it continues happening, or if the pool operator finds and fixes an issue.
...

I closed my miner 10 mins ago. The zcoin dashboard went from 800h/s to 1.1kH/s.....  "Hashrate based on shares submitted in the past 5 minutes." Im not sure what's going on here. These stats make no sense...

hash rate is actually reported late. Its more current in the worker page but also late.

[Myth888]

I am mining vertcoin and i have 31 mh/s but on website it shows 15mh/s and highest it shows 26mh/s.
I am not submitting any bad share so why does it not show actual hashrate? Also vertcoin mining takes long time to show any info. Anyone can help?

I had this problem with older versions of ccminer. I recently switched to v2.2.3.

https://github.com/tpruvot/ccminer/releases

The program reports a lower hashrate than other versions of ccminer, but the pool reports a much higher one. Keep in mind pool reported hashrate varies and can take a long time to show changes. But with the newer miner it actually reports the correct hashrate once in awhile. Not always half or less.

I'm observing reported hashrates significantly below miner values even with tpruvot ccminer 2.2.3. Usually it will show around 25Mh/s in worker stats for 28MH/s working, but at times it will report lower values.

The dashboard gauge seems to have a lot of averaging going on, because when I looked at it a few hours ago it only said 2 MH/s but some time later had corrected itself up to 24 MH/s.



As for being able to customize the auto switching a little to factor in things like capabilities and power consumption, that would be an amazing feature. Depending on what language it is in, I'd be willing to help make it happen.

You can try contacting MPH operator directly. Hes easy to talk to but has been really busy lately. Try him on email or skype.

[Gongolo]

Yes, but excavator3 is the best one for other alorythms (And works fine for them) :/

Anyways, i tried it and the other ones worked fine. Until ExcavatorNvidia3.. take that out as well? What is the diff between 2 and 3?

Where can I find Excavator?
Does it work with any pool or is it nicehash hardcoded?

MiningPoolHub is blocked by default but MultiPoolMiner bypasses the block:
https://github.com/aaronsace/MultiPoolMiner/releases

Thank you, I will give it a try.

[puch0021]

I have a port question when using AwesomeMiner + Mining Pool Hub + 1060 rigs

Is the configuration supposed to use 17xxx (Algo switch mining) or 12xxx (Multi-algo switch mining) ports?

Miningpoolhub indicates 17XXX is best for asics whereas 12XXX is best for GPUS. When I go through the default configuration through AwesomeMiner it automatically sets up each algorithm with 17XXX though that seems incorrect.

Thoughts?

Ex:For LyraREv2

stratum+tcp://hub.miningpoolhub.com:17018
or
stratum+tcp://hub.miningpoolhub.com:12018

See: https://miningpoolhub.com/index.php?page=gettingstarted

[SuperDerpBro]

Yes, but excavator3 is the best one for other alorythms (And works fine for them) :/

Anyways, i tried it and the other ones worked fine. Until ExcavatorNvidia3.. take that out as well? What is the diff between 2 and 3?

Where can I find Excavator?
Does it work with any pool or is it nicehash hardcoded?

MiningPoolHub is blocked by default but MultiPoolMiner bypasses the block:
https://github.com/aaronsace/MultiPoolMiner/releases

Thank you, I will give it a try.

ExcavatorNvidia3.. take that out as well? What is the diff between 2 and 3 versions of these?

[OdinYggd]

I have a port question when using AwesomeMiner + Mining Pool Hub + 1060 rigs

Is the configuration supposed to use 17xxx (Algo switch mining) or 12xxx (Multi-algo switch mining) ports?

Miningpoolhub indicates 17XXX is best for asics whereas 12XXX is best for GPUS. When I go through the default configuration through AwesomeMiner it automatically sets up each algorithm with 17XXX though that seems incorrect.

Thoughts?

Ex:For LyraREv2

stratum+tcp://hub.miningpoolhub.com:17018
or
stratum+tcp://hub.miningpoolhub.com:12018

See: https://miningpoolhub.com/index.php?page=gettingstarted

Both are valid, here's the difference:

Port numbers of 17xxx will always mine the specified algo, but may change what coin is actually being mined.
Port numbers of 12xxx are auto switch ports, and are turned on and off at MPH by the algo profitability switching. A miner connected here will be disconnected when that algo is not currently profitable.

You can try contacting MPH operator directly. Hes easy to talk to but has been really busy lately. Try him on email or skype.

Its not really that important to me at least, merely a nusiance issue. The actual profitability compares favorably to the theoretical values, so the gauge is just a nice thing to make sure its all still working.

2. On the Zcoin Dashboard, I can see the Recent Credits for the past few days.
On 2017-12-08 it was noticeably lower, at about 1020AM UTC, I stopped receiving shares. At about 1220PM I received the email "no shares from worker in 10min". I logged in via TV and it was running as expected. But the shares only resumed at about 0930PM UTC.

How can I debug this? My Monero miner was still going strong, so it cannot be the network connection.

I think this was a pool issue last night, since my 24h profitability is about half of what I was expecting. There were some website issues last night, and a database issue as well that resulted in shares not being credited.

Lets see if it continues happening, or if the pool operator finds and fixes an issue.
...

I closed my miner 10 mins ago. The zcoin dashboard went from 800h/s to 1.1kH/s.....  "Hashrate based on shares submitted in the past 5 minutes." Im not sure what's going on here. These stats make no sense...

I think the dashboard gauge has a significant amount of time weighted averaging going on, it seems to take quite a while to reflect changes in miner output and never catches up 100%. Every time I look at it I find some weird number from 0 to hashrate.

[l33twannabe]

I am mining vertcoin and i have 31 mh/s but on website it shows 15mh/s and highest it shows 26mh/s.
I am not submitting any bad share so why does it not show actual hashrate? Also vertcoin mining takes long time to show any info. Anyone can help?

I had this problem with older versions of ccminer. I recently switched to v2.2.3.

https://github.com/tpruvot/ccminer/releases

The program reports a lower hashrate than other versions of ccminer, but the pool reports a much higher one. Keep in mind pool reported hashrate varies and can take a long time to show changes. But with the newer miner it actually reports the correct hashrate once in awhile. Not always half or less.

Where do you see those stats (reported hashrate etc.) ? I can't find it anywhere on the MPH site ...

[Eam0kgIO]

Profitability calculation bug?

CcminerTpruvot  Scrypt          2,09 MH/s 0,00401    1,91914 Zpool

This seems pretty high for my 2MHs. If I put it into cryptocompare the reward is 0.0004033LTC

[DKu]

Hi
This is miningpoolhub operator

1. Sorry for late reply.
...

2. Here's my task list I'm focusing.
...

3. Thank you for your trust, and patience during the previous 80 minutes of website crash.
...

First of all Big thanks for your work. You have a great and fair pool.
I have only one question: why I'm not seeing any data on VTC dashboard and also coins in wallet? My rig have a full job, but nothing activity on pool. With MONA there was no any problems.

[SuperDerpBro]

Is there any way to keep multipoolminer OFF zpool? It is still mining there from time to time. Only mining pool hub is in the bat and none of the algorithms in the bat file are not supported by mining pool hub..

Also, ExcavatorNvidia3 and Excavator3.. what is the diff between 2 and 3 versions of these?

[aaronsace]

Is there any way to keep multipoolminer OFF zpool? It is still mining there from time to time. Only mining pool hub is in the bat and none of the algorithms in the bat file are not supported by mining pool hub..

Also, ExcavatorNvidia3 and Excavator3.. what is the diff between 2 and 3 versions of these?

Delete it from the folder called 'pools'.

Excavator dropped AMD support so they are now the same.

[SuperDerpBro]

Thanks

MiningPoolHubCoins - what is this one for?

Also, do you ever sleep? haha

[Sityl]

Hey all.  I've signed up to use Mining Pool Hub, and I've set up to convert to bitcoin.  I plan on mining to the pool through awesome miner.  I can't see anywhere on the mining pool website where to put my bitcoin wallet address for payout, and on awesomeminer, it asks for my MPH user name, not bitcoin address.  Can someone please walk me through how to input my wallet address?

Thanks very much,
-Sityl

[aaronsace]

Thanks

MiningPoolHubCoins - what is this one for?

Also, do you ever sleep? haha

Not enough.

It uses the individual coin ports instead of the algorithm ports. The algorithm ports should always be the most profitable but it's in there as an option.