Let me chime in with another tip, do not attempt to clean these gears with a strong air compressor especially when they are hot, the other day I wanted to give the gears a good dusting, took one perfectly working S17 pro, took out the hashboards, put them on a clean table and I blew the life out of them, heatsinks starting flying like mosquitoes, I know since they fell that easily it was only a matter of time before they start falling off, but I could use a month or two of gears running stable.
|
|
|
There is no "best" gear for everyone, a single answer that fits everyone's situation does not exist, the most important factor in your decision would be the power cost. So if you have a cheap electricity rate then you might want to buy cheaper mining gears and focus mainly on the cost per TH to utilize that edge of power you have, if your power rate is in the middle then that's a different story if it's on the high end - forget about mining altogether.
|
|
|
The only way a person can get rich in CHINA is to cheat the buyer, and honest guy always loses in China.
This statement is so mean and is actually racist, you are saying that every successful seller in China is a scammer/liar, which is not the case. Of course, the majority of those sellers are not honest, but it isn't half as bad as you show it. The problem with these mining gear sellers on Alibaba and Aliexpress is that most of them do NOT own any mining gears, they will either 'dropship' or buy the miner for you and reship it, some don't even know how to troubleshoot those gears before sending them out, and given that mining gears have a very high failure rate, there is always a good chance you end up with a broken miner. Those "honest" seller will offer a refund if you return the miner, but well, you will lose a good portion of your money if something like that happens, I have done some deals on Aliexpress, some went well, most were terrible, and I would advise against buying used mining gears from both Alibaba and Aliexpress.
|
|
|
What is the AC voltage at the wall? are you sure you have the M21 and not the M21s?
|
|
|
Does a miner actually have the right to choose a transaction to process over the other?
Yes, they can even chose to NOT include any transactions at all. Maybe, he'll probably choose as transaction with a higher transaction fee over the one with small transaction fee, thereby causing an undue delay. OR This is exactly how things work if you send a transaction with x fees, and just so happen that there are enough transactions that pay x+ a fraction to keep the blocks full for say 10 days, then your transaction will be stuck for 10 days. There is an expectation which is the miner's rewards for pool miners, most pools will include their daily reward transactions in the first block they mine regardless of the fees, the other exception is some entities such as Marathon which mines "OFAC Compliant Bitcoin Blocks", in other words, they censorship transactions coming in/going to addresses that are blacklisted by the "Office of Foreign Assets Control" even if those transactions pay 10 times more fees than the rest.
|
|
|
Hello which firmware is best for replace with bitmain original firmware for t17e device ?
Thanks.
The only custom firmware I would use would be Vnish or BO+, both don't have one for the T17e model, however, thierry4wd has a modified version of the original one which has some great reviews, you can find it here.
|
|
|
At this point in time, I think PPS is the way to go, whether you are a large or a small miner, you need to go with the assumption that the pool's luck is and will be 100%, which makes the long term gains between to pools identical minus the difference in fees.
Given the competition in PPS pools, you can find solid pools with fees as low as 2.5%, the cheapest PPLNS pool would be just below 1% for small pools that hardly find a block and might never find a block from now on, the larger once will have a higher fee, but let's just say it's 1.5%, so the difference is 1% in fees, would you rather save 1% and risk losing a day or a week or even 11 months worth of mining just to save that massive 1%?
|
|
|
best comment here, but where do u buy the hw? I'm here in asia, and I don't see any, everything is 'out of stock', hdd's, gpu's, .. power-supplys all is GONE
Maybe because you are searching in the wrong place, prices fell in China just a while ago, for that to reflect on other regions it will take some time, but it will most certainly happen, if you want to take advantage of the current prices in China you need to contact Chinese sellers, most of these websites are not based in China, and most Chinese sellers do their sales on telegram and Alibaba/Aliexpress. There are a few Chinese sellers in this forum, you can find their sale posts in the hardware market place
|
|
|
I have an S17 + where the red LED lights up permanently. Since the LED has been on, I can no longer find it in the network.
Assuming you performed the reset in the correct way "which I doubt", then the control board is likely dead, but before jumping to a conclusion, you have to Sdcard the control board. Go to this link > https://service.bitmain.com/support/download?product=Flashing%20SD%20card%20with%20imageDownload (SD_S17+.rar), get a Sdcard ready, format it to FAT32, and follow the steps mentioned here. But before doing all that, try to use a different LAN cable.
|
|
|
It has since been taken off the Google Play Store in accordance with their updated policies, but I used to use an app called Crypto Miner by Jesus Oliver. That's legit -- actually mines... albeit very, VERY slowly, as everyone else in the thread has already noted.
It's highly unlikely that your mobile phone will hit a share that gets accepted by any mining pool, in other words, that app you mentioned or any other app for that matter does not really mine bitcoin, the most common thing they do is collect your data and sell it for marketing purposes, they get paid for it and pay you a small portion, there could be a few more ways they can make money of your phone resources, mining bitcoin isn't one of them, so just because an app pays you something (large or small) it does mean it actually mines bitcoin, it's most certainly doing something else that generates some sort of a revenue someway, somehow.
|
|
|
Not sure what your 'simple' math is, but you're talking about faulty miners and putting them back together with bits a pieces.
it is simple logic, some of these custom firmware do "revive" hash boards that the stock firmware fails to detect because it is a piece of shit for most miners, getting a hashboard back to life and paying 2%, 3% or even 5% is, of course, a lot better than saving on fees with your hash boards sitting on the sideline earning you nothing. Another major advantage is the auto-tune, the stock firmware sets everything at default, custom firmware such as BO+ reduce the power consumption by a good margin which makes the fees justifiable as far as the user is concerned because if I can save a total of $100 on power and pay $20 on fees, I'll happily accept it, in fact, I believe anyone with common sense would, not sure about you. psus are all hard to find.
I think grace has PSUs for the 17 and 19 series in stock for 200+.
|
|
|
So there are people wanting the gear
There is always someone who wants some gears, most of the time it's the noobs who can't do the math and think mining bitcoin will make them rich overnight, looking at the big picture, Bitcoin mining gears prices took a huge dive in China, today, S19 pro was sold for $7980, all the way down from 15k a few weeks ago, difficulty needs to go 12.5T or price to 60k for those who bought S19s at 15k to actually ROI within a year or so, and honestly I don't see either happening anytime soon. With that being said, if someone is fully positioned in fiat and wants to start mining, the current prices are far less risky, it might be a good idea to start accumulating gears now, especially that it seems like the sideways boring market is going to last for a few months, it's the best time for mining as it easily beats the buy-n-hodl model.
|
|
|
لايوجد اوفر كلوك امن, اي تغير في الفولت او التردد الافتراضي يزيد من احتمالية تعطل رقاقات الجهاز وتوقفه عن التعدين, عندما تصنح هده الرقاقات تخضع لاختبارات دقيقة يتم فيها تحديد قدرتها الانتجاية المثالية وليست القصوى, وتحديد هده القدرة يعتمد على درجة الحرارة, استهلاك الكهرباء ,التكلفة المادية وغيرها من العوامل, يحاول المصنع دائما المزج بين كل هده المدخلات والوصول الى "المثالية" في خياراته, عند تغير هده الاعدادات فأنت تقوم بتحميل الجهاز فوق قدرته في معظم الاحيان.
السؤال الذي يجب ان تسئله لنفسك هوا هل نحن اذكى من الشركة المصنعة؟ الاجابة ببساطة "لا", اذا عندما تبيع الشركة جهاز تعدين بقدرة 10 تيرا بسعر 10$ اي دولار للتيرا ( على سبيل المثال) وتقوم انت بعمل اوفر كلوك له ليصبح 12 تيرا , مالذي يمنع المصنع نفسه ان يفعل هدا ونحن نعلم انهم يمكنهم فعل هدا وبيعه ب 12$؟ الامر ببساطة هوا كل تلك العوامل المذكورة اعلاه وايضا لان المصنع ملزم بأعطاءك ضمانة لفترة معينة ويعمل كل جهده على تجنب استقبال الجهاز من جديد لصيانته او تعويضك ببديل له لان ذلك مكلف, فهم يحالون بشتى الطرق ان يشغتل الجهاز معك طوال فترة الضمانة لكي يتجنبو المصاريف الباهضة وايضا الحفاظ على جودة منتجاتهم وضمان عملها لاطول فترة ممكنة.
طبعا البعض يريد تجاهل كل هده الاشياء ويريد عمل اوفر كلوك, الموضوع سهل جدا, تقوم بتحميل Firmware خاص يتيح لك التحكم بالفولت والتردد ويوجد اصدارات مجانية مثل BraiinOS, البرامج الاخرى الغير مجانية (تأخد نسبة من الهاش ريت) تقوم بعمل شي يسمى auto-tune اي انك تحدد الهاش ريت المطلوب ويقوم البرنامج اوتوماتكيا بتغير تردد كل شريحة على حدا لمحاولة الوصول الى السرعة المطلوبة.
طبعا هده البرامج ليست متاحة لكل الاجهزة وبعضها يشغتل على اجهزة معينة دون غيرها, لذلك يجب عليك تحديد نوع الجهاز لكي اقوم باخبارك عن الخيارات المتاحة.
|
|
|
If all 12 units stopped hashing at the same time then it's likely a pool/network-related issue, can you try a different pool? I don't have AvalonMiner but with Antminers you can ping the pool using the miner, I suppose Avalon would have even more network troubleshooting tools.
|
|
|
انا ضد شراء هده الاجهزة لعدة اسباب, اهما هوا معدل الزيادة في مستوى الصعوبة, طبعا يمكن ان تقول ان هدا الشي ينطبق على البتكوين ايضا, هدا صحيح ولكن النقطة التي لا يقوم بحسابها اغلب المعدنين الجدد هي "سرعة" زيادة الصعوبة, وهنا يأتي جمال الرياضايات والارقام.
لو اخدنا عملة KDA فان الهاش ريت الحالي لها هوا حوالي 9 بيتا هاش اي 9000 تيرا, احد اجهزة الاسك وهي التي تكلمت عنها حضرتك KD5 يمكنه تعدينها بقوة 18 تيرا, مما يعني اننا تحتاج فقط 500 جهاز لمضاعفة الصعوبة اي خسارة نصف الدخل.
لو قمنا بنفس هده المقارنة على البتكوين, الهاش الحالي 130 اكسا هاش, اي مايعادل 130,000 بيتا هاش, او 130,000000 تيرا هاش, لكي نقوم بمضاعفة الهاش ريت باستخدام احدث اجهزة التعدين مثلا بهاش 100 تيرا لكل جهاز نحتاج الى 1,300,000 جهاز , مبدئيا لايوجد شركة قادرة على تصنيع هدا الكم خلال فترة سنة او حتى سنتين, وحتى ان زادت هده الشركات قدرتها الانتاجية فأن تكلفة هده الاجهزة بسعرها الحالي في الاسواق 10 الاف دولار للجهاز اي حوالي 13 مليار دولار, من شبه المستحيل ان يحدث هدا الشي في فترة قصيرة, بينما فرصة صناعة وبيع 500 جهاز KD5 او حتى 5000 جهاز فهي واردة جدا ويمكن ان تحدث في اسبوعين او شهرين.
لذلك تجد ان دخل هده الاجهزة في البداية يكون عالي جدا حيت يصل الدخل احيانا الى الاف الدولارات في الاسبوع الواحد, ولكن فور استلام اول دفعة تجد ان الدخل انفخض بنسبة 90% او اكثر, فأن لم تكن من اول الاشخاص الذين تحصلو على هده الاجهزة (وهدا امر شبه مستحيل لان الشركات المصنعة في العادة تحتكر هدا الشي) فأنت على الاغلب سوف تخسر.
طبعا يوجد شواد لهده القاعدة فمثلا يمكن ان يرتفع سعر العملة 100 ضعف ليعوض تضاعف الصعوبة, فمثلا اجهزة L3 لتعدين لايت كوين ودوق كوين كان دخلها اقل من دولار ليقفر فوق ال 10$ عندما ارتفع سعر عملة دوق كوين وهنا قد استفاد كل من يملك اجهزة تعدين لايت كوين وقامو بجني ارباح طائلة, ولكن هل من العقلانية ان تستتمر اموالك وتتمنى حدوث شي غريب مثل هدا؟ لقد شاهدانا مئات العملات التي تفقد 99% من قيمتها بين يوم وليلة, عند شرائك لجهاز تعدين عملة معينة فأنت تراهن على بقائها ونموها وايضا ارتفاع سعرها, لذلك بالنسبة لي فالخيار دائما سهل, بتكوين او ايثيريوم هم فقط العملتين التي يمكن ان نقول عنهم مضمونات وصعوبتهم وصلت لارقام يصعب تحريكها للاعلى بنسب جنونية, والخيار بين البتكوين والايثيريم ايضا سهل وهوا يرجح البتكوين, الا طبعا في حال انك لاتستطيع شراء اجهزة اسك وتريد استعمال كروت الشاشة فعندها الايثيريوم افضل (بالرغم من ان الايثيريوم سوف تنتقل الى POS يوما ما على اي حال).
|
|
|
-First symptom was "0 Asic found". I repaired a few cold solder joints. ( I measured CLK pins with an oscilloscope ) -After repair Test Fixture found 65 ASIC chips, but then showed the problem with thermal sensors. -Then i found on 1 ASIC chip only 1,3Volts on pins(CO-RI-RST), another cold solder, problem with 1V8 power supply line. -Then i found bad resistance among 1V8 power supply lines. I measured the first and the last ASIC chip in the line (5-Asics in line). Resistance was 2-3 Ohms but must be 0-Ohms. -> Another cold solder
Would you explain more about "cold solder" did you find some solder balls shorting some legs/pins? it would be great if you could share some more info (photos would be really nice). What firmware is installed on this machine? can you test with custom firmware like Vnish or BO+ ? I prefer the former, you can get it on Asic.to or AwoesomeMiner website (both have some fees 2-3%), these custom firmware "ignore" some things that the stock does not, there is a good chance that the miner might work with custom firmware. # 0: pattern test # 1: only find asic
Great that you chimed in, what does the pattern test actually do aside from counting chips?
|
|
|
!!! WARNING: This user is a newbie. If you are expecting a message from a more veteran member, then this is an imposter !!!
يبدو ان احد ما يحاول التحايل عليك, كن حذر وتأكد ان الرسالة فعلا جائت مني, رابط قناة التليقرام التي ارستلها لك هوا https://t.me/minerexpertsales ومديره اسمها grace وحسابها على التليقرام هوا @gracezhou1993 الكثير من المحتالين يستخدمون اسامي تشابه اسامي ناس موثوقة لكي يتحايلو على ضحايهم, يجب عليك دائما التأكد انك تتحدث مع الشخص نفس, كأجراء احتراجي في حل قررت ان تشتري قبل تحويل اي اموال يمكننا التأكيد معي, ربما يمكن ان ترسل لي العنوان الذي طلب البائع التحويل اليه واقوم بالتأكد منه ان كان فعلا عنوان ينتمي له او نجد اي طريقة اخرى للتأكيد المهم انك يجب ان تكون حذر فمستوى النصب في هدا المجال يفوق الخيال, ايضا اريد تذكيرك بما اخبرتك به في الرسالة انه وبالرغم من اني تعاملت مع grace عشرات المرات واعتقد انها اهل للثقة الا اني لا اتحمل مسؤولية اي شي قد يحدث بينكم لا سمح الله.
|
|
|
كنت اميل الى كوننا نعيد سيناريو مشابه ل 2016-2017 ولكن مع مرور الوقت في هده السايكل وخصوصا بعد الهبوط الاخير تبين لي انني كنت مخطاء واننا على الارجع سنعيد ماحصل في 2013, يعني اننا في "بير ماركت مصغر" ان صح التعبير, واتوقع ان يستمر السعر تحت 40 الف لاشهر ربما حتى نهاية السنة او الاشهر الاخيرة منها قبل البدء فعلا في التحرك الى الاعلى, في نفس الوقت لا اعتقد اننا سنرا مستويات ال 10 الاف وغيرها.
|
|
|
شكرا لردك انا مقيم في تركيا حاولت اعرف التفاصيل حول الجمارك وغيره ولم اتوصل لاي اجابة واضحة في تركيا من حيث التكاليف الاخرى ان كان لديك معلومات سوف تختصر الكثير علي وايضا ارقام موردين للكميات ولطلبات الشخصية
اعتقد ان الضرائب في تركيا على الاجهزة الالكترونية عالية جدا وربما يتم مصادرة اجهزة التعدين, والاهم من كل هدا ان سعر الكهرباء في تركيا مرتفع ولن يكون التعدين هناك مجدي, ارجو ان تحققك من كل هده المعلومات قبل المخاطرة لكي لاتتعرض للمشاكل. في حال لا زلت تصر على الشراء ارسل لي رسالة على الخاص وسوف ارسل لك حساب تليقرام احد الباعة في الصين ويمكنك التواصل معها مباشرة.
|
|
|
At first when you turn on, the main panel it indicates "socket connect failed connection refused" but after a while it normalizes and it seems that it would start to work but the hash does not raise.
It's pretty normal for the miner to show socket connection failed when it's booting, don't worry about that. 2021-06-16 17:45:58 power_api.c:86:get_average_voltage: chain[2], voltage is: 17.879297 2021-06-16 17:45:58 power_api.c:97:get_average_voltage: aveage voltage is: 17.876235
Seems like the voltage is a bit too low, it's likely that you have a bad PSU, can you confirm if all 3 fans on the PSU are spinning? also can you test 1 hash board at a time?
|
|
|
|