It really doesn't work:

UNKNOWN OPTION -logfile
UNKNOWN OPTION Claymorelog

Good idea.. sometimes I have about 75degrees by tt 80 and fan at 25%
It could be cooler if fan is faster

-U --cuda-extragpu-mem 4096 --cuda-streams 1 --cuda-block-size 64 --cuda-grid-size 4096
for genoil
for ccminer i use 1.8.2 with -i 23 no special parameter (but also not specifing intensity is giving me same results)

After update on genoil 20 mh\s, your miner don't run and says that Opencl.dll is not found (Why Opencl for Nvidia ). I have updated to 1607 Win 10 (Anniversary) and didn't touch the drivers.

-U --cuda-extragpu-mem 4096 --cuda-streams 1 --cuda-block-size 64 --cuda-grid-size 4096
for genoil
for ccminer i use 1.8.2 with -i 23 no special parameter (but also not specifing intensity is giving me same results)

at the moment  claymore you should improve the code for libry coin... im speaking as nvidia user... not profitable to use your miner....
genoil + ccminer running at same time on windows  will produce approximately 13% more than your miner  and for free
3 x 1070 gtx @ 70 % power  will produce 36 mhas eth and 610 lbry coin ... and no fee involved (except the pool fee dwarf pool... suprnova has no fee if i remember.) 365 w from the wall ( approximaterly 330 w REAL considering psu efficency. 100w /gpu considering 30w for system)
24h tested stable
alternatively we can give more priority to eth  and produce with same settings  67 Eth and  270 lbry

Good day. Tell me what kind of error and whether it affects what the realties.
ETH: Received error: {"id":4,"result":null,"error":[21,"jobnotfound"]}

Would say it's ok if yours was 1070, but it's 1080.
I'm on GTX 970 Ti and Win 10 Anniversary x64 and get 4 Mhs (which i don't think it's ok). Drivers don't change it, latest or 352.84.

NVIDIA DRIVERS:
9xx cards in Windows 7 x64: just use latest/recent drivers from Nvidia website (for example, 368.81). Note that latest 372.54 is slower than 368.81.
9xx cards in Windows 10 x64: you have to use old drivers (for example, 352.xx) and miner built for cuda6.5. 
10xx cards in Windows 7 x64: just use latest 372.54 drivers from Nvidia website.
10xx cards in Windows 10 x64: just use latest 372.54 drivers from Nvidia website, note that you must have Win10 Anniversary update.

@claymore, eth + SC or eth+lbc is 2%fee...
eth +dcr 1%fee?
that's according to op on 1st page.  mind to clarify?
thx.

This miner is free-to-use, however, current developer fee is 1% for Ethereum-only mining mode (-mode 1) and 2% for Ethereum+Decred mining mode (-mode 0)

Is there any way to specify difficulty in dual mining? like lbry static difficulty setting?
Thank you

Command tar failed with return code 0 and error message
Like in previous version... What does it mean?

Claymore, is there any workaround for gtx 1080 (372.90 / win 10) and not getting 5 Mhs ?

Claymore my miner thread hangs frequently, and it wont restart. I mean when remote-connect to the machine and on the miner window press down arrow "miner thread hanged, restarting" message pops up, but untill I do so, the machine just stays in freeze mode for 4 - 6 hours causing me significant loss. I need to keep checking on machines almost regular. I have set the miner to restart every 60 minutes with -r 60 but nothing happens. I'm using Ver 7.1 of your miner on RX 470's, 16.9.2 drivers on Win 10.

The temp monitor will work in linux right ? if it is overheat it will stop the gpu

Have you devoloped any xmg miner,are you thinking to release it?

Thanks Claymore !
Is it going to be posted on google drive soon ? I don't see it yet.

@Claymore
I have some questions
I use your miner for solo mining. When I solo mine 7.0 version rigs find more block then 7.1. Because of this I turned back to 7.0. I think something is wrong with 7.1 for solo mining and also if there is an issue, I don't know it still exists in 7.2 too. I use geth windows for etc. I run it from a different pc from the rigs in lan.
Is it possible to put an option for GTX 1070 cards to disable fan speed monitoring from miner?
I have RX 470 and GTX 1070 but I still don't know Which ''-etha'' option must I use for my card. If you write optimized cards or slow cards, I will be glad.
My last question is about ''-etht'' Would you put more explanation about it?  There aren't too much things and option in read me and mining forum communities. Because of this I need your help to use all the options for full optimization.

I'm still on version 6.4
It has been stable for weeks now, so I don't see any reason why I should change.
Unless there is some mining speed improvement  
That was not the case with version 7.0, and a lot of folks felt that.
@Claymore, have made any improvements to the mining code?
PS: I run RX 480s

Thank you claymore, you're the best. I only wished you would open source ethman so we can make it a lot better.

Hello

Its possible that claymore bat send a email to me when miner stopped?

Thanks

is it a known issue with rx 480 8gb  that it takes 60-90 seconds after showing "POOL/SOLO version" for the miner to proceed to DAG generation?
happens on all my 4 rigs with windows 7/windows 10

Claymore, you could fix the issue when using NVIDIA GPUs without fans (watercooling, server-grade GPUs, etc.):

Claymore, any idea what the following might be?

4x RX470, win10:

10:56:51:597   1150   em hbt: 0, dm hbt: 0, fm hbt: 63,
10:56:51:597   1150   watchdog - thread 0, hb time 78
10:56:51:613   1150   watchdog - thread 1, hb time 219
10:56:51:613   1150   watchdog - thread 2, hb time 219
10:56:51:613   1150   watchdog - thread 3, hb time 94
10:56:51:613   1150   watchdog - thread 4, hb time 109
10:56:51:613   1150   watchdog - thread 5, hb time 234
10:56:51:613   1150   watchdog - thread 6, hb time 23828
10:56:51:628   1150   watchdog - thread 7, hb time 23688
10:56:51:628   1150   WATCHDOG: GPU error, you need to restart miner
Faulty GPU, or Riser?
Thanks in advance, if you have a XMR address I'll buy you an untraceable beer^^

3 threads put it down to 47:

Claymore could you make something like "GPU-reordering" command, so that the GPU number in miner and in GPU-Z are synchronized? Both for ETH and XMR miner.

-logfile 0 do not working at 7.1

-logfile debug log file name. After restart, miner will append new log data to the same file. If you want to clear old log data, file name must contain "noappend" string.
   If missed, default file name will be used.

finally got fast mode enabled.. but it does not seam to be faster then when it said slow mode.  I have a phenom 6 core:

-t number of threads. "-t 0" - autoselection. Autoselection does not work fine in all cases, so try different values.
   Optimal value depends mostly on L3 cache size. 
   For example, if your CPU has 8 MB of L3 cache (i7 CPUs), use "-t 4". For 6MB L3 cache (i5 CPUs) use "-t 3".