dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
|
December 14, 2015, 01:18:27 AM |
|
AriesIV10 just mentioned this on the forum and they are right. The RPM's on your fans are WAY TO LOW! If it is on auto, take it off of auto and put it on manual to 100% as soon as possible. At least 80 or 85 percent minimum. My guess is you already have them on manual and need to increase the percentage.
|
|
|
|
Prelude
Legendary
Offline
Activity: 1596
Merit: 1000
|
|
December 14, 2015, 01:31:27 AM |
|
He said he needed the miner to be quiet despite the heat.
Guess keeping it around is less important.
|
|
|
|
Biodom
Legendary
Offline
Activity: 3906
Merit: 4379
|
|
December 14, 2015, 01:32:21 AM |
|
AriesIV10 just mentioned this on the forum and they are right. The RPM's on your fans are WAY TO LOW! If it is on auto, take it off of auto and put it on manual to 100% as soon as possible. At least 80 or 85 percent minimum. My guess is you already have them on manual and need to increase the percentage. I am very curious about how high temperatures would affect the lifespan of S7. It seems that from purely chips perspective, everything is peachy for OP even at as high as 73C (as far as error rates are concerned). I try to maintain less than 60C, but some folks swear for mid 60ies as a better range. It would be very difficult fact to establish. On the other hand, SPT was fine at up to 115C (direct chip temp, though). i would hate to miss out on a potential +5-10 % of the hashing IF it does not affect the lifespan, but it is a big IF, of course. On the other hand, why would Bitmain optimized fans (I am talking about auto) for 45-55C when they could have run them at 65C if it is all good at those temperatures?
|
|
|
|
wangfuYONG
Newbie
Offline
Activity: 1
Merit: 0
|
|
December 14, 2015, 01:43:42 AM |
|
Might actually pick one of these up. How much is it again?
Looks like 7.972 BTCHope not. That's quite pricey. Although, I paid 4.92BTC for an S1. And that doesn't include shipping or taxes. this is good ,I like it
|
|
|
|
scyth33
Member
Offline
Activity: 99
Merit: 10
|
|
December 14, 2015, 01:50:24 AM |
|
does anyone have problem with bitmain when doing wire transfer?
|
|
|
|
mikefallen
Member
Offline
Activity: 72
Merit: 10
|
|
December 14, 2015, 02:27:23 AM |
|
does anyone have problem with bitmain when doing wire transfer?
I did it the first miners i bought and it was a pain in the ass at least in canada. Had to pay 2.5 % conversions fee from CAD --> USD also it's like $100 fee from the bank, at least for me it was. BTC defiantly the way to go.
|
Bitcointalk Trading Address: 149cRHxme8kP4grxg2f7cgyYTqGhZzvj6f
|
|
|
PeaMine
|
|
December 14, 2015, 02:41:06 AM |
|
My issue with ordering was a PC issue. Ordered from my phone and it all went smooth.
|
Datacenter Technician and Electrician. If you have any questions feel free to ask me as I am generally bored looking at logs and happy to help during free time.
|
|
|
klondike_bar
Legendary
Offline
Activity: 2128
Merit: 1005
ASIC Wannabe
|
|
December 14, 2015, 03:34:39 AM |
|
I'm home again and have tested my batch 8 with my "3 lower end server psu's" DPS-600s:
4110Ghs 600Mhz 1140W 4150Ghs 625Mhz 1200W 4398Ghs 650Mhz 1245W 4490Ghs 675Mhz 1285W 4700Ghs 700Mhz 1335W
Chips seem to like about 60c temp, I get less errors as reported by others. I have fans at 45% inlet fan at 3960, outlet 3720, I took some static fins away from exhaust fan. When I unboxed miner and left it to work for weekend speed was 4500Ghs with stock fan speed of 4600. Efficiency about 0.28 I get Bitmain powers next week and test again.
Thats good to see - efficiency is not terribly affected by frequency. (600GH/200W overall)
|
|
|
|
ATCkit
|
|
December 14, 2015, 03:42:04 AM |
|
does anyone have problem with bitmain when doing wire transfer?
I did it the first miners i bought and it was a pain in the ass at least in canada. Had to pay 2.5 % conversions fee from CAD --> USD also it's like $100 fee from the bank, at least for me it was. BTC defiantly the way to go. Wow- I'm in Canada too. My bank didn't charge me nearly as much. The conversion fee was about the same- but the transfer fee was only $13. I'm with RBC. Anyway, the transfer went well and showed as paid in about 1 business day for me. All in all, I wasn't as bad as i had anticipated. Having said that, I agree that BTC is definitely the way to go.
|
|
|
|
clgrissom3
Legendary
Offline
Activity: 1722
Merit: 1032
Carl, aka Sonny :)
|
|
December 14, 2015, 03:47:11 AM |
|
I stayed up to read the NEC till 6:30am this morning. I slept until 2:30pm. It is 3:30pm now. I do not see it written like what prelude provided regarding the "feeder to the breaker.' However, I do see many references of "...marked 100%." So, I must conclude 80% is the rule for all Main breakers and other breakers installed in the Main Panel or Sub Panels unless otherwise stated on the breaker that is listed. Now, I'm going to have to determine [After talking to electrician] if it will be cheaper to have a 700 amp service provided by the power company and installed by the electrician to get what I want [OR] get a 600 amp service with special breakers "marked 100%" in special panels. I'm not sure which will be cheaper but I will find out and pass that information along in the forum. Thanks for getting me to investigate this more, Prelude. Now, back to more reading of the NEC 2015. David EDIT: I went backward and deleted about 3 posts to save space in the forum. I know this type of project is right up your alley and you've already pulled the trigger so to speak but you seem to be the perfect candidate for having your S7s hosted in a data center. Good luck and I hope it all works out for you so you can get all of your machines pointed towards Kano!
|
|
|
|
ATCkit
|
|
December 14, 2015, 03:53:48 AM |
|
clgrissom3, I'm having a beer now to celebrate your block find. Amazing to have 2 blocks found back to back by guys with 20 THS. cheers bud!
|
|
|
|
dmwardjr
Legendary
Offline
Activity: 1302
Merit: 1318
Technical Analyst/Trader
|
|
December 14, 2015, 05:39:07 AM Last edit: December 14, 2015, 08:33:16 AM by dmwardjr |
|
I know this type of project is right up your alley and you've already pulled the trigger so to speak but you seem to be the perfect candidate for having your S7s hosted in a data center. Good luck and I hope it all works out for you so you can get all of your machines pointed towards Kano!
Yes, I'm pulling the trigger. I'm just the type of guy who prefers to do it themselves. If anything were to go wrong with a rig, there is no one to blame buy myself or the manufacturer [Depending on what went wrong]. I feel better not being concerned about if anything went wrong, would I be compensated for the loss of a rig(s). I've seen too many horror stories for me to risk 78 or more rigs potentially getting lost, stolen, burned up, etc... then hope they had insurance that would take care of it IN AN EFFICIENT AND TIMELY MANNER. There are good hosting centers I might consider trusting in the future, such as, Toomin, sidehack, or Oregon Miners. That's about it. In the mean time, I intend to keep going here till I reach 600 amp demand and cannot add anymore. THEN, I will see about hosting the rest afterwards. The price savings between keeping them for myself verses hosting is very little difference IMHO. At least during the winter. At present, my revenue is 4 times my power costs. EDIT: BY THE WAY, Good job finding that block on kano.is
|
|
|
|
mkextremer
Newbie
Offline
Activity: 8
Merit: 0
|
|
December 14, 2015, 09:42:16 AM |
|
I know this type of project is right up your alley and you've already pulled the trigger so to speak but you seem to be the perfect candidate for having your S7s hosted in a data center. Good luck and I hope it all works out for you so you can get all of your machines pointed towards Kano!
Yes, I'm pulling the trigger. I'm just the type of guy who prefers to do it themselves. If anything were to go wrong with a rig, there is no one to blame buy myself or the manufacturer [Depending on what went wrong]. I feel better not being concerned about if anything went wrong, would I be compensated for the loss of a rig(s). I've seen too many horror stories for me to risk 78 or more rigs potentially getting lost, stolen, burned up, etc... then hope they had insurance that would take care of it IN AN EFFICIENT AND TIMELY MANNER. There are good hosting centers I might consider trusting in the future, such as, Toomin, sidehack, or Oregon Miners. That's about it. In the mean time, I intend to keep going here till I reach 600 amp demand and cannot add anymore. THEN, I will see about hosting the rest afterwards. The price savings between keeping them for myself verses hosting is very little difference IMHO. At least during the winter. At present, my revenue is 4 times my power costs. EDIT: BY THE WAY, Good job finding that block on kano.isdmwardjr sir I can see that youre experienced in bitcoin and bitcoin mining. I plan on buying the S7 Batch 8. I live in Macedonia so the estimated shipping is $150 for the miner and the PSU. I want to ask you what the life span of the S7 is, without overclocking. So I pay $1450 for miner and PSU, $150 for shipping, $80 for electricity each month. Will it be profitable now or in the future? I just got into bitcoin, dont know much.
|
|
|
|
lanfeusst
|
|
December 14, 2015, 10:03:25 AM Last edit: December 14, 2015, 11:05:05 AM by lanfeusst |
|
Here is some Overvolting - overclocking of my S7 Batch 1 with DPS-2000BB and J4bberwock breakout board. Getting ~ 5660Gh/s, Voltage is 12.75 V under full load. Power consumption at the wall is 1590Watt => 0.28J/Gh efficiency I know it runs hot, but I need the silence.
AriesIV10 just mentioned this on the forum and they are right. The RPM's on your fans are WAY TO LOW! If it is on auto, take it off of auto and put it on manual to 100% as soon as possible. At least 80 or 85 percent minimum. My guess is you already have them on manual and need to increase the percentage. Thank you for the advice but I want to keep the noise at a minimum. The fan is set to manual at 28% If the temps goes > 75C, I will adjust the fan to 30%. Each 2% gives you ~ 4°C less temps. Furthermore I checked BM1385 temp rating and Bitmain indicates here that they can take up to 125°C (Operation temperature : max 125°C) : https://bitmaintech.com/files/download/BM1385_Datasheet_v2.0.pdfI know the temp sensor is not on the chips but on the boards but it should work fine I think (If chips are less than 45-50C over the temp sensor it should be good)
|
|
|
|
bittalc1
|
|
December 14, 2015, 10:56:59 AM |
|
Hey guys, Anyone knows some software for multi managing S7's like the m miner monitor? Thanks
|
|
|
|
geotete
Newbie
Offline
Activity: 12
Merit: 0
|
|
December 14, 2015, 12:03:21 PM |
|
I know this type of project is right up your alley and you've already pulled the trigger so to speak but you seem to be the perfect candidate for having your S7s hosted in a data center. Good luck and I hope it all works out for you so you can get all of your machines pointed towards Kano!
Yes, I'm pulling the trigger. I'm just the type of guy who prefers to do it themselves. If anything were to go wrong with a rig, there is no one to blame buy myself or the manufacturer [Depending on what went wrong]. I feel better not being concerned about if anything went wrong, would I be compensated for the loss of a rig(s). I've seen too many horror stories for me to risk 78 or more rigs potentially getting lost, stolen, burned up, etc... then hope they had insurance that would take care of it IN AN EFFICIENT AND TIMELY MANNER. There are good hosting centers I might consider trusting in the future, such as, Toomin, sidehack, or Oregon Miners. That's about it. In the mean time, I intend to keep going here till I reach 600 amp demand and cannot add anymore. THEN, I will see about hosting the rest afterwards. The price savings between keeping them for myself verses hosting is very little difference IMHO. At least during the winter. At present, my revenue is 4 times my power costs. EDIT: BY THE WAY, Good job finding that block on kano.isdmwardjr sir I can see that youre experienced in bitcoin and bitcoin mining. I plan on buying the S7 Batch 8. I live in Macedonia so the estimated shipping is $150 for the miner and the PSU. I want to ask you what the life span of the S7 is, without overclocking. So I pay $1450 for miner and PSU, $150 for shipping, $80 for electricity each month. Will it be profitable now or in the future? I just got into bitcoin, dont know much. Calculate here: http://www.coinwarz.com/cryptocurrency/?sha256hr=11000&sha256p=750.00&sha256pc=0.0000&sha256c=true&scrypthr=75000.00&scryptp=1500.00&scryptpc=0.1000&scryptc=false&scryptnhr=300.00&scryptnp=420.00&scryptnpc=0.1000&scryptnc=false&x11hr=13500.00&x11p=600.00&x11pc=0.1000&x11c=false&x13hr=9750.00&x13p=600.00&x13pc=0.1000&x13c=false&keccakhr=1260.00&keccakp=825.00&keccakpc=0.1000&keccakc=true&quarkhr=6300.00&quarkp=825.00&quarkpc=0.1000&quarkc=false&groestlhr=45.00&groestlp=825.00&groestlpc=0.1000&groestlc=true&blake256hr=6.40&blake256p=450.00&blake256pc=0.1000&blake256c=false&neoscrypthr=400.00&neoscryptp=400.00&neoscryptpc=0.1000&neoscryptc=false&lyra2rev2hr=13500.00&lyra2rev2p=825.00&lyra2rev2pc=0.1000&lyra2rev2c=false&cryptonighthr=1950.00&cryptonightp=750.00&cryptonightpc=0.1000&cryptonightc=false&e=Cryptsy
|
|
|
|
mkextremer
Newbie
Offline
Activity: 8
Merit: 0
|
|
December 14, 2015, 12:38:41 PM |
|
I know this type of project is right up your alley and you've already pulled the trigger so to speak but you seem to be the perfect candidate for having your S7s hosted in a data center. Good luck and I hope it all works out for you so you can get all of your machines pointed towards Kano!
Yes, I'm pulling the trigger. I'm just the type of guy who prefers to do it themselves. If anything were to go wrong with a rig, there is no one to blame buy myself or the manufacturer [Depending on what went wrong]. I feel better not being concerned about if anything went wrong, would I be compensated for the loss of a rig(s). I've seen too many horror stories for me to risk 78 or more rigs potentially getting lost, stolen, burned up, etc... then hope they had insurance that would take care of it IN AN EFFICIENT AND TIMELY MANNER. There are good hosting centers I might consider trusting in the future, such as, Toomin, sidehack, or Oregon Miners. That's about it. In the mean time, I intend to keep going here till I reach 600 amp demand and cannot add anymore. THEN, I will see about hosting the rest afterwards. The price savings between keeping them for myself verses hosting is very little difference IMHO. At least during the winter. At present, my revenue is 4 times my power costs. EDIT: BY THE WAY, Good job finding that block on kano.isdmwardjr sir I can see that youre experienced in bitcoin and bitcoin mining. I plan on buying the S7 Batch 8. I live in Macedonia so the estimated shipping is $150 for the miner and the PSU. I want to ask you what the life span of the S7 is, without overclocking. So I pay $1450 for miner and PSU, $150 for shipping, $80 for electricity each month. Will it be profitable now or in the future? I just got into bitcoin, dont know much. Calculate here: http://www.coinwarz.com/cryptocurrency/?sha256hr=11000&sha256p=750.00&sha256pc=0.0000&sha256c=true&scrypthr=75000.00&scryptp=1500.00&scryptpc=0.1000&scryptc=false&scryptnhr=300.00&scryptnp=420.00&scryptnpc=0.1000&scryptnc=false&x11hr=13500.00&x11p=600.00&x11pc=0.1000&x11c=false&x13hr=9750.00&x13p=600.00&x13pc=0.1000&x13c=false&keccakhr=1260.00&keccakp=825.00&keccakpc=0.1000&keccakc=true&quarkhr=6300.00&quarkp=825.00&quarkpc=0.1000&quarkc=false&groestlhr=45.00&groestlp=825.00&groestlpc=0.1000&groestlc=true&blake256hr=6.40&blake256p=450.00&blake256pc=0.1000&blake256c=false&neoscrypthr=400.00&neoscryptp=400.00&neoscryptpc=0.1000&neoscryptc=false&lyra2rev2hr=13500.00&lyra2rev2p=825.00&lyra2rev2pc=0.1000&lyra2rev2c=false&cryptonighthr=1950.00&cryptonightp=750.00&cryptonightpc=0.1000&cryptonightc=false&e=CryptsyI'm getting revenue profit: $13.36 - $2.78 for electricity = $10.58 per day Is this considered good? And as I asked, what is the life span of the S7 Batch 8?
|
|
|
|
fullzero
Legendary
Offline
Activity: 1260
Merit: 1009
|
|
December 14, 2015, 12:41:28 PM |
|
AriesIV10 just mentioned this on the forum and they are right. The RPM's on your fans are WAY TO LOW! If it is on auto, take it off of auto and put it on manual to 100% as soon as possible. At least 80 or 85 percent minimum. My guess is you already have them on manual and need to increase the percentage. I am very curious about how high temperatures would affect the lifespan of S7. It seems that from purely chips perspective, everything is peachy for OP even at as high as 73C (as far as error rates are concerned). I try to maintain less than 60C, but some folks swear for mid 60ies as a better range. It would be very difficult fact to establish. On the other hand, SPT was fine at up to 115C (direct chip temp, though). i would hate to miss out on a potential +5-10 % of the hashing IF it does not affect the lifespan, but it is a big IF, of course. On the other hand, why would Bitmain optimized fans (I am talking about auto) for 45-55C when they could have run them at 65C if it is all good at those temperatures? I have ran all my S7's at ~62 C; I haven't had any problems. Each S7 hashes about 200gh/s more when using manual fans targeting 62C. Those of you who don't believe this; try it for a day with one of your S7's. If you are afraid of heat damage I suggest you get an old miner and stress test it. I have done this with many miners; I ran an S1 between 82 and 93C for 3 months. It had a higher error rate at that temp but otherwise was fine. Running fans at 80% or higher will only use more power and increase vibrations; which will eventually result in your heatsinks falling off.
|
|
|
|
|
clgrissom3
Legendary
Offline
Activity: 1722
Merit: 1032
Carl, aka Sonny :)
|
|
December 14, 2015, 01:45:11 PM |
|
clgrissom3, I'm having a beer now to celebrate your block find. Amazing to have 2 blocks found back to back by guys with 20 THS. cheers bud!
My first block ever...I hope everyone hits one!
|
|
|
|
|