captinkid
Newbie
 Offline
Activity: 38
Merit: 0
|
 |
December 16, 2016, 07:17:11 PM
Last edit: December 16, 2016, 08:00:13 PM by captinkid |
|
Greetings!
I have a S9 that decided to have a board partially quit randomly, then I stupidly upgraded the firmware to the 11/29 version, where it entered an endless loop of:
get_pic_software_version
get_pic_software_version: version[0] = 0x42
After restore: chain[0] PIC fw version=0x42
chain[0] PIC need restore ...
Once those fail, it never seems to get what it wants, it goes to count the asics per board and ends up with 0's, it never starts hashing. I've left it on overnight the last few nights, it gets in the need restore loop and never actually does any work.
Went back to the old firmware pre autotune and one of the good boards doesn't even try booting anymore (No flash or anything), so it's down to one working board.
I'm pretty sure it's down to the pic firmware, if I could find a way to flash it back and hopefully verify it to a previous version (Any ideas on what firmware version is good?) at least the two good boards should work.
I did try stealing the single-board-test file and config from the autotune version, I have it running on an old non autotune firmware trying to reset the pic on the boards. No luck so far, but it's getting different numbers, so I'm hopeful. Not sure of the batch #, I ordered them in early September. Cyclone V boards.
I have tried it with just one board connected at a time (Known good boards and the bad board) Still nothing even after hours of waiting per test.
(UPDATE)
It's version updated! Not sure if it's good yet, but it's progress
get_pic_software_version: version[0] = 0xcc
Check chain[0] PIC fw version=0xcc
chain[0] PIC need restore ...
Looks like single-board test is happy with version 0xcc, it's moved on to chain[1]
Darn, rebooted it and chain[0] is reading 0x00 again, it got reset / wiped randomly
I'm starting to wonder if their "repair" is just reflashing the hash board firmware with a special devkit. That could explain why they won't share the repair process, because it would cost them easy repair $$$.
|
|
|
|
|
|
|
|
|
|
|
|
"Your bitcoin is secured in a way that is physically impossible for others to access, no matter for what reason, no matter how good the excuse, no matter a majority of miners, no matter what." -- Greg Maxwell
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
HagssFIN
Legendary
Offline
Activity: 2436
Merit: 1706
Electrical engineer. Mining since 2014.
|
|
December 16, 2016, 07:27:54 PM |
|
Got damn it, I now have 1x dead hash board with my S9 11.85Ths non-autotune model.
I contacted BitmainWarranty.
Does someone from the EU area have some experience with them?
I know that the closest service point near me is Russia.
Let's see if they could fix it there.
|
|
|
|
smracer
Donator
Legendary
Offline
Activity: 1055
Merit: 1020
|
|
December 16, 2016, 07:33:31 PM |
|
I just unplug the bad boards and then it runs fine. Out of the 12 S9's I have bought from Bitmain, 5 of them have needed repair.
They have never gotten over 72F. I have 140 S7's and maybe 10 bad boards between them all. Out of the 200+ S5's I had there were maybe 5 bad boards total and out of the 300+ S3's I had maybe 4 bad boards.
I really hope they fix the S9's. The R4's seem to be running great. I have had no problems with them.
So 7 bad boards out of 36 total S9 boards = 19.4% failure rate. Ugh.
|
|
|
|
|
|
elokk
|
|
December 16, 2016, 07:42:44 PM |
|
I have had 3 bad boards from 7 s9's, 1 board out of 2 r4's. Very disappointing quality as of late from Bitmain
Still no word from Bitmain warranty in Denver on the board they have of mine and they arent responding to new repair tickets. Crappy quality control and even worse customer service
|
t.me/bitcoinasic
|
|
|
philipma1957
Legendary
Offline
Activity: 4116
Merit: 7824
'The right to privacy matters'
|
|
December 16, 2016, 07:51:49 PM |
|
I just unplug the bad boards and then it runs fine. Out of the 12 S9's I have bought from Bitmain, 5 of them have needed repair.
They have never gotten over 72F. I have 140 S7's and maybe 10 bad boards between them all. Out of the 200+ S5's I had there were maybe 5 bad boards total and out of the 300+ S3's I had maybe 4 bad boards.
I really hope they fix the S9's. The R4's seem to be running great. I have had no problems with them.
So 7 bad boards out of 36 total S9 boards = 19.4% failure rate. Ugh.
I am around 14-16% fail rate |
|
|
|
Biodom
Legendary
Offline
Activity: 3752
Merit: 3853
|
|
December 16, 2016, 07:54:45 PM |
|
I have had 3 bad boards from 7 s9's, 1 board out of 2 r4's. Very disappointing quality as of late from Bitmain
Still no word from Bitmain warranty in Denver on the board they have of mine and they arent responding to new repair tickets. Crappy quality control and even worse customer service
strange, they replied to me within 24hr, typically. did you check your service junk mail folder? In addition, some providers don't even show what they consider junk mail, which could make these emails invisible, so you have to go in and MANUALLY assign bitmainwarranty.com as a trusted domain. |
|
|
|
|
captinkid
Newbie
Offline
Activity: 38
Merit: 0
|
|
December 16, 2016, 08:09:31 PM
Last edit: December 17, 2016, 06:48:34 PM by captinkid |
|
Woo! I got a red light again on a hash board after:
get_pic_software_version: version[0] = 0x2
After restore: chain[0] PIC fw version=0x02
reset_iic_pic
It just needs to flash properly to both good boards and it should be good. Third board is probably still dead, may send it back for repairs or just save the money for a competitor machine down the road. Not sure I want to toss good money after bad with Bitmain.
Bad board is reading 0xf1, and the FW doesn't seem to want to update, I can't get it to change at all. Might just scrap it and let and let the two good ones run.
(UPDATE)
Looking good now:
jump_to_app_from_loader
get_pic_software_version
get_pic_software_version: version[0] = 0x2
Check chain[0] PIC fw version=0x02
reset_iic_pic
jump_to_app_from_loader
get_pic_software_version
get_pic_software_version: version[0] = 0x2
Check chain[2] PIC fw version=0x02
reset_iic_pic
jump_to_app_from_loader
get_pic_software_version
get_pic_software_version: version[0] = 0xf1
Check chain[3] PIC fw version=0xf1
chain[3] PIC need restore ...
(UPDATE)
Seems to fail writing firmware a VERY large amount of the time, even if it reads the version as correct the board firmware may still be corrupt / wrong version. I disconnected the first board that was successful so it wouldn't get ruined again by the fw loader. Now I'm running single-board-test against the last two boards until I get another success. The other good board should be fine once I get a good FW write to it.
|
|
|
|
|
|
elokk
|
|
December 16, 2016, 08:11:13 PM |
|
I have had 3 bad boards from 7 s9's, 1 board out of 2 r4's. Very disappointing quality as of late from Bitmain
Still no word from Bitmain warranty in Denver on the board they have of mine and they arent responding to new repair tickets. Crappy quality control and even worse customer service
strange, they replied to me within 24hr, typically. did you check your service junk mail folder? In addition, some providers don't even show what they consider junk mail, which could make these emails invisible, so you have to go in and MANUALLY assign bitmainwarranty.com as a trusted domain. definitely nothing in spam. I emailed them twice now and the second time I was told: "sale (Bitmain) Dec 9, 09:06 CST Teck is still attempting to repair fully. Please wait for next update" |
t.me/bitcoinasic
|
|
|
|
in2tactics
|
|
December 17, 2016, 11:11:14 PM |
|
My sp is not hashing but all the lights indicate it is working fine. The one line that concerns me is the one that says ethernet link up is full. Any suggestions? [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gf387dab-dirty (lzq@armdev01) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #38 SMP PREEMPT Fri Jun 17 20:02:51 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c06e4600, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=/dev/mtdblock1 rootfstype=jffs2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884528K/1032192K available (4764K kernel code, 271K rwdata, 1816K rodata, 200K init, 257K bss, 147664K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06752f8 (6581 kB)
[ 0.000000] .init : 0xc0676000 - 0xc06a8380 ( 201 kB)
[ 0.000000] .data : 0xc06aa000 - 0xc06edd00 ( 272 kB)
[ 0.000000] .bss : 0xc06edd0c - 0xc072e4fc ( 258 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000302] ps7-ttc #0 at f0006000, irq=43
[ 0.000603] Console: colour dummy device 80x30
[ 0.000638] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040205] pid_max: default: 32768 minimum: 301
[ 0.040415] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.040436] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.042511] CPU: Testing write buffer coherency: ok
[ 0.042853] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.042914] Setting up static identity map for 0x482448 - 0x4824a0
[ 0.043132] L310 cache controller enabled
[ 0.043151] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121023] CPU1: Booted secondary processor
[ 0.210226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210353] Brought up 2 CPUs
[ 0.210372] SMP: Total of 2 processors activated.
[ 0.210380] CPU: All CPU(s) started in SVC mode.
[ 0.211064] devtmpfs: initialized
[ 0.213435] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214641] regulator-dummy: no parameters
[ 0.221891] NET: Registered protocol family 16
[ 0.224079] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.226373] cpuidle: using governor ladder
[ 0.226386] cpuidle: using governor menu
[ 0.233755] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.235266] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.235280] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.235384] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.256938] bio: create slab <bio-0> at 0
[ 0.258364] vgaarb: loaded
[ 0.259061] SCSI subsystem initialized
[ 0.259941] usbcore: registered new interface driver usbfs
[ 0.260113] usbcore: registered new interface driver hub
[ 0.260381] usbcore: registered new device driver usb
[ 0.261107] media: Linux media interface: v0.10
[ 0.261978] Linux video capture interface: v2.00
[ 0.262264] pps_core: LinuxPPS API ver. 1 registered
[ 0.262276] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.262401] PTP clock support registered
[ 0.262772] EDAC MC: Ver: 3.0.0
[ 0.263806] Advanced Linux Sound Architecture Driver Initialized.
[ 0.266605] DMA-API: preallocated 4096 debug entries
[ 0.266618] DMA-API: debugging enabled by kernel config
[ 0.266697] Switched to clocksource arm_global_timer
[ 0.286457] NET: Registered protocol family 2
[ 0.287169] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.287264] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.287423] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.287490] TCP: reno registered
[ 0.287507] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.287559] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.287819] NET: Registered protocol family 1
[ 0.288176] RPC: Registered named UNIX socket transport module.
[ 0.288189] RPC: Registered udp transport module.
[ 0.288197] RPC: Registered tcp transport module.
[ 0.288205] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.288218] PCI: CLS 0 bytes, default 64
[ 0.288647] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.290670] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.292042] bounce pool size: 64 pages
[ 0.292918] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.293139] msgmni has been set to 1487
[ 0.293601] io scheduler noop registered
[ 0.293615] io scheduler deadline registered
[ 0.293651] io scheduler cfq registered (default)
[ 0.305941] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.305960] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.430808] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.003273] console [ttyPS0] enabled
[ 1.007569] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.015199] [drm] Initialized drm 1.1.0 20060810
[ 1.032139] brd: module loaded
[ 1.041540] loop: module loaded
[ 1.051113] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.056957] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.064686] libphy: XEMACPS mii bus: probed
[ 1.069081] ------------- phy_id = 0x3625e62
[ 1.073807] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.082582] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.089231] ehci-pci: EHCI PCI platform driver
[ 1.096439] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.103507] usbcore: registered new interface driver usb-storage
[ 1.110415] mousedev: PS/2 mouse device common for all mice
[ 1.116525] i2c /dev entries driver
[ 1.123457] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.129020] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.134904] Xilinx Zynq CpuIdle Driver started
[ 1.139763] sdhci: Secure Digital Host Controller Interface driver
[ 1.145859] sdhci: Copyright(c) Pierre Ossman
[ 1.150268] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.157022] mmc0: no vqmmc regulator found
[ 1.161035] mmc0: no vmmc regulator found
[ 1.196715] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.205401] usbcore: registered new interface driver usbhid
[ 1.210914] usbhid: USB HID core driver
[ 1.215654] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.221950] nand: Micron MT29F2G08ABAEAWP
[ 1.225918] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.231950] Bad block table found at page 131008, version 0x01
[ 1.238332] Bad block table found at page 130944, version 0x01
[ 1.244468] 4 ofpart partitions found on MTD device pl353-nand
[ 1.250233] Creating 4 MTD partitions on "pl353-nand":
[ 1.255342] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.263400] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.270710] 0x00000b000000-0x00000ec00000 : "upgrade-rootfs"
[ 1.277790] 0x00000ec00000-0x000010000000 : "upgrade-tmp"
[ 1.286395] TCP: cubic registered
[ 1.289687] NET: Registered protocol family 17
[ 1.294301] Registering SWP/SWPB emulation handler
[ 1.299966] regulator-dummy: disabling
[ 1.303743] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.314023] ALSA device list:
[ 1.316989] No soundcards found.
[ 4.499409] jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x01e7c7e4: Read 0xffffffff, calculated 0xc0816fa8
[ 4.512033] jffs2: Empty flash at 0x01e7c85c ends at 0x01e7d000
[ 5.171297] jffs2: jffs2_scan_inode_node(): CRC failed on node at 0x070177c0: Read 0xffffffff, calculated 0xccdc70f6
[ 5.186998] jffs2: Empty flash at 0x070178f8 ends at 0x07018000
[ 5.404304] VFS: Mounted root (jffs2 filesystem) on device 31:1.
[ 5.413285] devtmpfs: mounted
[ 5.416388] Freeing unused kernel memory: 200K (c0676000 - c06a8000)
[ 7.105760] random: dd urandom read with 1 bits of entropy available
[ 7.556711]
[ 7.556711] bcm54xx_config_init
[ 8.166707]
[ 8.166707] bcm54xx_config_init
[ 12.167569] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 12.173673] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 28.556514] In axi fpga driver!
[ 28.559588] request_mem_region OK!
[ 28.562977] AXI fpga dev virtual address is 0xf0112000
[ 28.568198] *base_vir_addr = 0x8c504
[ 28.586307] In fpga mem driver!
[ 28.589376] request_mem_region OK!
[ 28.592943] fpga mem virtual address is 0xf3000000
[ 29.976038]
[ 29.976038] bcm54xx_config_init
[ 30.625969]
[ 30.625969] bcm54xx_config_init
[ 34.626382] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 34.632537] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 84.118368] jffs2: warning: (1095) jffs2_do_read_inode_internal: Truncating ino #2068 to 19073 bytes failed because it only had 16032 bytes to start with!
[ 84.455066] jffs2: notice: (1095) check_node_data: wrong data CRC in data node at 0x02308f9c: read 0xbbc54e26, calculated 0x753115f3.
[ 404.614913] random: nonblocking pool is initialized
[151259.640205] xemacps e000b000.ps7-ethernet: link down
[151303.635815] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
use critical mode to search freq...
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x02
Check chain[6] PIC fw version=0x02
Check chain[7] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[27] has core num=1
Check chain[5] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[36] has core num=1
Check chain[6] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x02
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=108 on chain[7], value=880
chain[5] temp offset record: 62,-4,0,0,0,0,0,0
chain[6] temp offset record: 62,-4,0,0,0,0,0,0
chain[7] temp offset record: 62,-3,0,0,0,0,0,0
set command mode to VIL
singleBoardTest: AsicType = 1387
singleBoardTest: asicNum = 64
singleBoardTest: real AsicNum = 63
--- check asic number
set_baud=0, ought to be 1
The min freq=700
set real timeout 52, need sleep=379392
search freq for 1 times, completed chain = 3, total chain num = 3
disable_pic_dac on chain[5]
disable_pic_dac on chain[6]
disable_pic_dac on chain[7]
restart Miner chance num=2
waiting for send_func to exit of chain[0]
waiting for send_func to exit of chain[1]
waiting for send_func to exit of chain[2]
waiting for send_func to exit of chain[3]
waiting for send_func to exit of chain[4]
waiting for send_func to exit of chain[5]
waiting for send_func to exit of chain[6]
waiting for send_func to exit of chain[7]
waiting for send_func to exit of chain[8]
waiting for send_func to exit of chain[9]
waiting for send_func to exit of chain[10]
waiting for send_func to exit of chain[11]
waiting for send_func to exit of chain[12]
waiting for send_func to exit of chain[13]
waiting for send_func to exit of chain[14]
waiting for send_func to exit of chain[15]
waiting for receive_func to exit!
waiting for pic heart to exit!
Start bmminer ...
This is XILINX board.
Chain[J6] has backup chain_voltage=890
Chain[J6] test patten OK temp=78
Check chain[5] PIC fw version=0x02
Chain[J7] has backup chain_voltage=890
Chain[J7] test patten OK temp=73
Check chain[6] PIC fw version=0x02
Chain[J8] has backup chain_voltage=880
Chain[J8] test patten OK temp=70
Check chain[7] PIC fw version=0x02
Chain[J6] orignal chain_voltage=91 value=890
Chain[J7] orignal chain_voltage=91 value=890
Chain[J8] orignal chain_voltage=108 value=880
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[27] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[36] has core num=1
Chain[J8] has core num in PIC
miner total rate=13999GH/s fixed rate=13500GH/s
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:431
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:408 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:5 max freq=662
Chain:5 min freq=408
read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:350 Asic[18]:656 Asic[19]:643 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:512 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:681 Asic[48]:656
Asic[49]:656 Asic[50]:681 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=681
Chain:6 min freq=350
read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:468 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:416 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:656
Chain:7 max freq=662
Chain:7 min freq=416
Miner fix freq ...
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:431
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:408 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:5 max freq=643
Chain:5 min freq=408
read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:350 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:512 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:6 max freq=643
Chain:6 min freq=350
read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:468 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:416 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:7 max freq=643
Chain:7 min freq=416
max freq = 643
Chain[J6] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J6] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J7] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J7] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J8] PIC temp offset=62,-3,0,0,0,0,0,0
Chain[J8] chip[244] use PIC middle temp offset=-3 typeID=55
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
Chain[J6] set opencore voltage=920 [40]
Chain[J6] set working voltage=890 [91]
Chain[J7] set opencore voltage=920 [40]
Chain[J7] set working voltage=890 [91]
Chain[J8] set opencore voltage=920 [40]
Chain[J8] set working voltage=880 [108]
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
do heat board 8xPatten for 1 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=911 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=911 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=911 asic[50]=911 asic[51]=912 asic[52]=911 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[13]=911
core[096]=7
asic[20]=911
core[107]=7
asic[49]=911
core[029]=7
asic[50]=911
core[029]=7
asic[52]=911
core[014]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57451
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44339
last_nonce_num:36648
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=911 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=911 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=911
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=911 asic[53]=911 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[20]=911
core[030]=7
asic[41]=911
core[060]=7
asic[47]=911
core[071]=7
asic[52]=911
core[062]=7
asic[53]=911
core[066]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57451
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:49442
last_nonce_num:31602
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=911 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=911 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=911 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[16]=911
core[055]=7
asic[37]=911
core[029]=7
asic[52]=911
core[026]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57453
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44359
last_nonce_num:40723
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
do heat board 8xPatten for 2 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=911 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=911 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=911 asic[50]=912 asic[51]=911 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[06]=911
core[105]=7
asic[14]=911
core[019]=7
asic[43]=911
core[040]=7
asic[49]=911
core[003]=7
asic[51]=911
core[049]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57451
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44324
last_nonce_num:32802
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=911 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=911 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=911 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=911 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[05]=911
core[103]=7
asic[09]=911
core[081]=7
asic[12]=911
core[023]=7
asic[15]=911
core[066]=7
asic[24]=911
core[029]=7
asic[26]=911
core[045]=7
asic[36]=911
core[008]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57449
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:49446
last_nonce_num:29021
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=911 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=911 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=911 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[17]=911
core[003]=7
asic[22]=911
core[091]=7
asic[38]=911
core[016]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57453
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44352
last_nonce_num:34808
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
restartNum = 2 , auto-reinit enabled...
Chain[5] Chip[62] TempTypeID=55 middle offset=-4
read failed, old value: Chain[5] Chip[62] local Temp=69
overflow start using sw offset, old value: Chain[5] Chip[62] middle Temp=89
Chain[6] Chip[62] TempTypeID=55 middle offset=-4
read failed, old value: Chain[6] Chip[62] local Temp=66
overflow start using sw offset, old value: Chain[6] Chip[62] middle Temp=87
Chain[7] Chip[62] TempTypeID=55 middle offset=-3
read failed, old value: Chain[7] Chip[62] local Temp=67
overflow start using sw offset, old value: Chain[7] Chip[62] middle Temp=86
set FAN speed according to: temp_highest=89 temp_top1[PWM_T]=89 temp_top1[TEMP_POS_LOCAL]=69 temp_change=1 fix_fan_steps=1
FAN PWM: 78 Yes, I have a suggestion. Learn how to post within a code block. |
Current HW: 2x Apollo
Retired HW: 3x 2PAC, 3x Moonlander 2, 2x AntMiner S7-LN, 5x AntMiner U1, 2x ASICMiner Block Erupter Cube, 4x AntMiner S3, 4x AntMiner S1, GAW Black Widow, and ZeusMiner Thunder X6
|
|
|
rwwilson75
Newbie
Offline
Activity: 8
Merit: 0
|
|
December 18, 2016, 12:09:17 AM |
|
I apologize. Is that the pound symbol that says code or is there another way? Do you have any helpful input as far as why the miner appears to be OK as far as status lights but is not hashing?
|
|
|
|
|
|
mamiakimo
|
|
December 18, 2016, 12:14:40 AM |
|
I apologize. Is that the pound symbol that says code or is there another way? Do you have any helpful input as far as why the miner appears to be OK as far as status lights but is not hashing?
the new firmware can't work if one of your boards have an issue so just remove data cable from one board at a time and open your machine until you get the damaged one and you machine will work with 2 boards |
|
|
|
|
rwwilson75
Newbie
Offline
Activity: 8
Merit: 0
|
|
December 18, 2016, 12:36:11 AM |
|
I apologize. Is that the pound symbol that says code or is there another way? Do you have any helpful input as far as why the miner appears to be OK as far as status lights but is not hashing?
the new firmware can't work if one of your boards have an issue
so just remove data cable from one board at a time and open your machine until you get the damaged one and you machine will work with 2 boards
I don't think its the boards all green lights are flashing normally and I have no xxx's in the ASIC status. It will hash for a little bit and then go to o hashing. I have had a bad board before and had it repaired this seems different. I just received this s9 yesterday. I shouldnt have to download new firmware should I? I don't know how to read kernal logs but one line I noticed said ethernet up link (1000/FULL). [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gf387dab-dirty (lzq@armdev01) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #38 SMP PREEMPT Fri Jun 17 20:02:51 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c06e4600, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=/dev/mtdblock1 rootfstype=jffs2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884528K/1032192K available (4764K kernel code, 271K rwdata, 1816K rodata, 200K init, 257K bss, 147664K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06752f8 (6581 kB)
[ 0.000000] .init : 0xc0676000 - 0xc06a8380 ( 201 kB)
[ 0.000000] .data : 0xc06aa000 - 0xc06edd00 ( 272 kB)
[ 0.000000] .bss : 0xc06edd0c - 0xc072e4fc ( 258 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000305] ps7-ttc #0 at f0006000, irq=43
[ 0.000607] Console: colour dummy device 80x30
[ 0.000644] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040206] pid_max: default: 32768 minimum: 301
[ 0.040421] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.040442] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.042580] CPU: Testing write buffer coherency: ok
[ 0.042941] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043003] Setting up static identity map for 0x482448 - 0x4824a0
[ 0.043219] L310 cache controller enabled
[ 0.043239] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121027] CPU1: Booted secondary processor
[ 0.210226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210358] Brought up 2 CPUs
[ 0.210376] SMP: Total of 2 processors activated.
[ 0.210385] CPU: All CPU(s) started in SVC mode.
[ 0.211052] devtmpfs: initialized
[ 0.213438] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214689] regulator-dummy: no parameters
[ 0.223310] NET: Registered protocol family 16
[ 0.225623] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.227935] cpuidle: using governor ladder
[ 0.227949] cpuidle: using governor menu
[ 0.235435] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.236968] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.236982] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.237093] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.259020] bio: create slab <bio-0> at 0
[ 0.260750] vgaarb: loaded
[ 0.261996] SCSI subsystem initialized
[ 0.262885] usbcore: registered new interface driver usbfs
[ 0.263055] usbcore: registered new interface driver hub
[ 0.263298] usbcore: registered new device driver usb
[ 0.263825] media: Linux media interface: v0.10
[ 0.263983] Linux video capture interface: v2.00
[ 0.264226] pps_core: LinuxPPS API ver. 1 registered
[ 0.264238] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.264362] PTP clock support registered
[ 0.264722] EDAC MC: Ver: 3.0.0
[ 0.265784] Advanced Linux Sound Architecture Driver Initialized.
[ 0.268742] DMA-API: preallocated 4096 debug entries
[ 0.268757] DMA-API: debugging enabled by kernel config
[ 0.268846] Switched to clocksource arm_global_timer
[ 0.289841] NET: Registered protocol family 2
[ 0.290522] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.290619] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.290778] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.290853] TCP: reno registered
[ 0.290870] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.290928] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.291200] NET: Registered protocol family 1
[ 0.291588] RPC: Registered named UNIX socket transport module.
[ 0.291601] RPC: Registered udp transport module.
[ 0.291610] RPC: Registered tcp transport module.
[ 0.291618] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.291632] PCI: CLS 0 bytes, default 64
[ 0.292087] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.294160] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.295624] bounce pool size: 64 pages
[ 0.296533] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.296750] msgmni has been set to 1487
[ 0.297233] io scheduler noop registered
[ 0.297246] io scheduler deadline registered
[ 0.297284] io scheduler cfq registered (default)
[ 0.307872] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307892] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.434240] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.006732] console [ttyPS0] enabled
[ 1.011041] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.018702] [drm] Initialized drm 1.1.0 20060810
[ 1.035762] brd: module loaded
[ 1.045262] loop: module loaded
[ 1.055033] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.060896] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.068679] libphy: XEMACPS mii bus: probed
[ 1.073088] ------------- phy_id = 0x3625e62
[ 1.077836] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.086553] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.093213] ehci-pci: EHCI PCI platform driver
[ 1.100635] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.107454] usbcore: registered new interface driver usb-storage
[ 1.114382] mousedev: PS/2 mouse device common for all mice
[ 1.120523] i2c /dev entries driver
[ 1.127428] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.132972] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.138887] Xilinx Zynq CpuIdle Driver started
[ 1.143745] sdhci: Secure Digital Host Controller Interface driver
[ 1.149888] sdhci: Copyright(c) Pierre Ossman
[ 1.154182] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.161013] mmc0: no vqmmc regulator found
[ 1.165027] mmc0: no vmmc regulator found
[ 1.208883] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.217568] usbcore: registered new interface driver usbhid
[ 1.223088] usbhid: USB HID core driver
[ 1.227834] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.234126] nand: Micron MT29F2G08ABAEAWP
[ 1.238095] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.244123] Bad block table found at page 131008, version 0x01
[ 1.250539] Bad block table found at page 130944, version 0x01
[ 1.256683] 4 ofpart partitions found on MTD device pl353-nand
[ 1.262458] Creating 4 MTD partitions on "pl353-nand":
[ 1.267558] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.275637] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.283018] 0x00000b000000-0x00000ec00000 : "upgrade-rootfs"
[ 1.290123] 0x00000ec00000-0x000010000000 : "upgrade-tmp"
[ 1.298798] TCP: cubic registered
[ 1.302069] NET: Registered protocol family 17
[ 1.306715] Registering SWP/SWPB emulation handler
[ 1.312371] regulator-dummy: disabling
[ 1.316176] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.326590] ALSA device list:
[ 1.329523] No soundcards found.
[ 5.585234] VFS: Mounted root (jffs2 filesystem) on device 31:1.
[ 5.594255] devtmpfs: mounted
[ 5.597361] Freeing unused kernel memory: 200K (c0676000 - c06a8000)
[ 7.270427] random: dd urandom read with 1 bits of entropy available
[ 7.668870]
[ 7.668870] bcm54xx_config_init
[ 8.278860]
[ 8.278860] bcm54xx_config_init
[ 12.279718] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 12.285828] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 29.888333] In axi fpga driver!
[ 29.891403] request_mem_region OK!
[ 29.894792] AXI fpga dev virtual address is 0xf0112000
[ 29.899938] *base_vir_addr = 0x8c504
[ 29.919501] In fpga mem driver!
[ 29.922573] request_mem_region OK!
[ 29.926139] fpga mem virtual address is 0xf3000000
[ 31.338194]
[ 31.338194] bcm54xx_config_init
[ 31.978093]
[ 31.978093] bcm54xx_config_init
[ 35.978570] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 35.984674] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 84.887577] jffs2: warning: (1095) jffs2_do_read_inode_internal: Truncating ino #2068 to 19073 bytes failed because it only had 16032 bytes to start with!
[ 282.565855] random: nonblocking pool is initialized
use critical mode to search freq...
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x02
Check chain[6] PIC fw version=0x02
Check chain[7] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[27] has core num=1
Check chain[5] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[36] has core num=1
Check chain[6] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x02
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=108 on chain[7], value=880
chain[5] temp offset record: 62,-4,0,0,0,0,0,0
chain[6] temp offset record: 62,-4,0,0,0,0,0,0
chain[7] temp offset record: 62,-3,0,0,0,0,0,0
set command mode to VIL
singleBoardTest: AsicType = 1387
singleBoardTest: asicNum = 64
singleBoardTest: real AsicNum = 63
--- check asic number
set_baud=0, ought to be 1
The min freq=700
set real timeout 52, need sleep=379392
search freq for 1 times, completed chain = 3, total chain num = 3
disable_pic_dac on chain[5]
disable_pic_dac on chain[6]
disable_pic_dac on chain[7]
restart Miner chance num=2
waiting for send_func to exit of chain[0]
waiting for send_func to exit of chain[1]
waiting for send_func to exit of chain[2]
waiting for send_func to exit of chain[3]
waiting for send_func to exit of chain[4]
waiting for send_func to exit of chain[5]
waiting for send_func to exit of chain[6]
waiting for send_func to exit of chain[7]
waiting for send_func to exit of chain[8]
waiting for send_func to exit of chain[9]
waiting for send_func to exit of chain[10]
waiting for send_func to exit of chain[11]
waiting for send_func to exit of chain[12]
waiting for send_func to exit of chain[13]
waiting for send_func to exit of chain[14]
waiting for send_func to exit of chain[15]
waiting for receive_func to exit!
waiting for pic heart to exit!
Start bmminer ...
This is XILINX board.
Chain[J6] has backup chain_voltage=890
Chain[J6] test patten OK temp=78
Check chain[5] PIC fw version=0x02
Chain[J7] has backup chain_voltage=890
Chain[J7] test patten OK temp=73
Check chain[6] PIC fw version=0x02
Chain[J8] has backup chain_voltage=880
Chain[J8] test patten OK temp=70
Check chain[7] PIC fw version=0x02
Chain[J6] orignal chain_voltage=91 value=890
Chain[J7] orignal chain_voltage=91 value=890
Chain[J8] orignal chain_voltage=108 value=880
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[27] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[36] has core num=1
Chain[J8] has core num in PIC
miner total rate=13999GH/s fixed rate=13500GH/s
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:431
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:408 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:5 max freq=662
Chain:5 min freq=408
read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:350 Asic[18]:656 Asic[19]:643 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:512 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:681 Asic[48]:656
Asic[49]:656 Asic[50]:681 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=681
Chain:6 min freq=350
read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:468 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:416 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:656
Chain:7 max freq=662
Chain:7 min freq=416
Miner fix freq ...
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:431
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:408 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:5 max freq=643
Chain:5 min freq=408
read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:350 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:512 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:6 max freq=643
Chain:6 min freq=350
read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:468 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:416 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:7 max freq=643
Chain:7 min freq=416
max freq = 643
Chain[J6] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J6] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J7] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J7] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J8] PIC temp offset=62,-3,0,0,0,0,0,0
Chain[J8] chip[244] use PIC middle temp offset=-3 typeID=55
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
Chain[J6] set opencore voltage=920 [40]
Chain[J6] set working voltage=890 [91]
Chain[J7] set opencore voltage=920 [40]
Chain[J7] set working voltage=890 [91]
Chain[J8] set opencore voltage=920 [40]
Chain[J8] set working voltage=880 [108]
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
do heat board 8xPatten for 1 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=911 asic[19]=911 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=911 asic[47]=911
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=911 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[10]=911
core[107]=7
asic[18]=911
core[089]=7
asic[19]=911
core[064]=7
asic[46]=911
core[055]=7
asic[47]=911
core[055]=7
asic[60]=911
core[007]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57450
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:51502
last_nonce_num:35641
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=911 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=911 asic[12]=912 asic[13]=911 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=911 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=911 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=911 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=911 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=911 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[05]=911
core[061]=7
asic[10]=911
core[019]=7
asic[11]=911
core[019]=7
asic[13]=911
core[067]=7
asic[14]=911
core[063]=7
asic[21]=911
core[083]=7
asic[25]=911
core[030]=7
asic[30]=911
core[037]=7
asic[37]=911
core[052]=7
asic[52]=911
core[005]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57446
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44368
last_nonce_num:37018
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=911 asic[20]=911 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=911 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[12]=911
core[092]=7
asic[14]=911
core[094]=7
asic[19]=911
core[057]=7
asic[20]=911
core[053]=7
asic[26]=911
core[035]=7
asic[48]=911
core[040]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57450
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:50456
last_nonce_num:33309
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
do heat board 8xPatten for 2 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=911 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[10]=911
core[059]=7
asic[15]=911
core[029]=7
asic[46]=911
core[063]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57453
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:49422
last_nonce_num:32058
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=911
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=911 asic[14]=912 asic[15]=912
asic[16]=911 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=911 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=911 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[07]=911
core[030]=7
asic[13]=911
core[041]=7
asic[16]=911
core[112]=7
asic[22]=911
core[070]=7
asic[57]=911
core[055]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57451
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:50461
last_nonce_num:31431
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=911 asic[02]=910 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=911 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=911 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[01]=911
core[092]=7
asic[02]=910
core[046]=7 core[092]=7
asic[12]=911
core[006]=7
asic[15]=911
core[057]=7
asic[18]=911
core[066]=7
asic[26]=911
core[031]=7
asic[51]=911
core[110]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57448
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44345
last_nonce_num:31732
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
restartNum = 2 , auto-reinit enabled...
Chain[5] Chip[62] TempTypeID=55 middle offset=-4
Chain[5] Chip[62] local Temp=68
Chain[5] Chip[62] middle Temp=89
Chain[6] Chip[62] TempTypeID=55 middle offset=-4
Chain[6] Chip[62] local Temp=66
Chain[6] Chip[62] middle Temp=86
Chain[7] Chip[62] TempTypeID=55 middle offset=-3
Chain[7] Chip[62] local Temp=66
Chain[7] Chip[62] middle Temp=85
set FAN speed according to: temp_highest=89 temp_top1[PWM_T]=89 temp_top1[TEMP_POS_LOCAL]=68 temp_change=1 fix_fan_steps=3
FAN PWM: 82
|
|
|
|
|
|
Longsnowsm
|
|
December 18, 2016, 12:47:26 AM |
|
1000 FULL just means you are running Gigabit ethernet, full duplex. I don't own an S9 so I may be speaking out of turn, but that is typically what that means when you see something like that.
|
|
|
|
|
captinkid
Newbie
Offline
Activity: 38
Merit: 0
|
|
December 18, 2016, 09:13:03 AM
Last edit: December 18, 2016, 11:02:19 AM by captinkid |
|
Found the 10/27 and 11/08 autotune firmwares didn't have their test data obfuscated like in the 11/25 and 11/29 versions. More data to try to reverse engineer the asic fw programming process. They also used a different version of single-board-test for both 10/27 and 11/08, looks like they were an early work in progress when they were released. Still have two bad boards, the controller can communicate with the PICs but they fail all of the tests. Once the fw fails to restore them a dozen times it fails over to bmminer and starts with no boards online in the GUI. The hash_s8_app.txt appears to have the software for the PIC, it's 3200 lines and the restore process is 3200 blocks.  Looks like all of the autotune versions use the exact same hashboard firmware code, 10/27, 11/08, 11/25, and 11/29. If I can find a way to pull that code from one of the good pre autotune hash boards I might be able to rewrite it to the failed boards and get them running again. But they didn't come with that code in their firmware. Might be a lost cause, too many dark tunnels of obfuscated code that they are keeping secret. Rather than sending these boards in for repair I'd rather spend the money on an Avalon or something else down the road. Bitmain devices seem to be terribly flaky and poorly designed. But as long as I have them to play with I will. If anyone has any autotune firmwares before 10/27 please let me know! I'd love to have a copy for my work. (UPDATE) Renaming hash_s8_app.txt causes the single-board-test to NOT restore the firmware a trillion times, but it still does all the other steps. Not useful for me, but really a time saver and interesting. All I want is a little program with full R/W access to the hashboard memory and PIC, that can't be too much to ask can it? Unfortunately the tools to do that are all locked up in the single-board-test binary and associated bits with no source code available.  |
|
|
|
|
HerbPean
Legendary
Offline
Activity: 1638
Merit: 1005
|
|
December 18, 2016, 05:49:34 PM |
|
All I want is a little program with full R/W access to the hashboard memory and PIC, that can't be too much to ask can it? Unfortunately the tools to do that are all locked up in the single-board-test binary and associated bits with no source code available. Go check the sidehack thread about the S7-LN, I think this is what sidehack do to tweak them. (Not sure) |
|
|
|
|
captinkid
Newbie
Offline
Activity: 38
Merit: 0
|
|
December 18, 2016, 06:33:55 PM
Last edit: December 18, 2016, 07:25:52 PM by captinkid |
|
I'll take a look, thanks!
(UPDATE)
Yup, that's probably exactly what I needed! I ordered a tester off of ebay, now just to wait and see. I'm guessing it's a similar procedure to what they're doing on the S7LN.
Might be a way to fix hashboard softbricks soon if it works, without going through Bitmain! I'll be happy to share when I get it figured out.
|
|
|
|
|
HagssFIN
Legendary
Offline
Activity: 2436
Merit: 1706
Electrical engineer. Mining since 2014.
|
|
December 18, 2016, 08:56:57 PM |
|
I now just tried with the PICkit3 to: 1. Read a good PIC firmware from a good hash board 2. Write a good PIC firmware to a dead hash board No effect. The dead hash board is still dead. So it is probably not just "soft bricked". So I wait for the answer from BitmainWarranty ( www.bitmainwarranty.com). I have previous experience with the PICkit3. |
|
|
|
captinkid
Newbie
Offline
Activity: 38
Merit: 0
|
|
December 18, 2016, 10:18:54 PM
Last edit: December 18, 2016, 10:34:31 PM by captinkid |
|
I now just tried with the PICkit3 to: 1. Read a good PIC firmware from a good hash board 2. Write a good PIC firmware to a dead hash board No effect. The dead hash board is still dead. So it is probably not just "soft bricked". So I wait for the answer from BitmainWarranty ( www.bitmainwarranty.com). I have previous experience with the PICkit3. Do you have the image file from the good hash board? I'd like to have a look at it if you could send it to me. In what way is your board dead? Mine died immediately AFTER a firmware update, it never hashed on the new firmware, so I'm pretty sure it's software related, unless the bad software caused something to overheat. Bitmain thinks it's an incompatible firmware, which is weird because they said it was for "all" but we'll see if they can help me. They responded to my first e-mail and I gave them more information, now I'm waiting to hear back. Thankfully I only flashed one of my S9's, the rest will probably never get a firmware update, it's too risky. |
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4116
Merit: 7824
'The right to privacy matters'
|
|
December 18, 2016, 10:29:57 PM |
|
I apologize. Is that the pound symbol that says code or is there another way? Do you have any helpful input as far as why the miner appears to be OK as far as status lights but is not hashing?
the new firmware can't work if one of your boards have an issue
so just remove data cable from one board at a time and open your machine until you get the damaged one and you machine will work with 2 boards
I don't think its the boards all green lights are flashing normally and I have no xxx's in the ASIC status. It will hash for a little bit and then go to o hashing. I have had a bad board before and had it repaired this seems different. I just received this s9 yesterday. I shouldnt have to download new firmware should I? I don't know how to read kernal logs but one line I noticed said ethernet up link (1000/FULL). [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.0-xilinx-gf387dab-dirty (lzq@armdev01) (gcc version 4.8.3 20140320 (prerelease) (Sourcery CodeBench Lite 2014.05-23) ) #38 SMP PREEMPT Fri Jun 17 20:02:51 CST 2016
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=18c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine model: Xilinx Zynq
[ 0.000000] cma: CMA: reserved 128 MiB at 27800000
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] On node 0 totalpages: 258048
[ 0.000000] free_area_init_node: node 0, pgdat c06e4600, node_mem_map e6fd8000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 194560 pages, LIFO batch:31
[ 0.000000] HighMem zone: 496 pages used for memmap
[ 0.000000] HighMem zone: 63488 pages, LIFO batch:15
[ 0.000000] PERCPU: Embedded 8 pages/cpu @e6fc0000 s9088 r8192 d15488 u32768
[ 0.000000] pcpu-alloc: s9088 r8192 d15488 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256528
[ 0.000000] Kernel command line: noinitrd mem=1008M console=ttyPS0,115200 root=/dev/mtdblock1 rootfstype=jffs2 rw rootwait
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 884528K/1032192K available (4764K kernel code, 271K rwdata, 1816K rodata, 200K init, 257K bss, 147664K reserved, 253952K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06752f8 (6581 kB)
[ 0.000000] .init : 0xc0676000 - 0xc06a8380 ( 201 kB)
[ 0.000000] .data : 0xc06aa000 - 0xc06edd00 ( 272 kB)
[ 0.000000] .bss : 0xc06edd0c - 0xc072e4fc ( 258 kB)
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Dump stacks of tasks blocking RCU-preempt GP.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=2.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=2
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] ps7-slcr mapped to f0004000
[ 0.000000] zynq_clock_init: clkc starts at f0004100
[ 0.000000] Zynq clock init
[ 0.000015] sched_clock: 64 bits at 333MHz, resolution 3ns, wraps every 3298534883328ns
[ 0.000305] ps7-ttc #0 at f0006000, irq=43
[ 0.000607] Console: colour dummy device 80x30
[ 0.000644] Calibrating delay loop... 1325.46 BogoMIPS (lpj=6627328)
[ 0.040206] pid_max: default: 32768 minimum: 301
[ 0.040421] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.040442] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.042580] CPU: Testing write buffer coherency: ok
[ 0.042941] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.043003] Setting up static identity map for 0x482448 - 0x4824a0
[ 0.043219] L310 cache controller enabled
[ 0.043239] l2x0: 8 ways, CACHE_ID 0x410000c8, AUX_CTRL 0x72760000, Cache size: 512 kB
[ 0.121027] CPU1: Booted secondary processor
[ 0.210226] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.210358] Brought up 2 CPUs
[ 0.210376] SMP: Total of 2 processors activated.
[ 0.210385] CPU: All CPU(s) started in SVC mode.
[ 0.211052] devtmpfs: initialized
[ 0.213438] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 0.214689] regulator-dummy: no parameters
[ 0.223310] NET: Registered protocol family 16
[ 0.225623] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.227935] cpuidle: using governor ladder
[ 0.227949] cpuidle: using governor menu
[ 0.235435] syscon f8000000.ps7-slcr: regmap [mem 0xf8000000-0xf8000fff] registered
[ 0.236968] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.236982] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.237093] zynq-ocm f800c000.ps7-ocmc: ZYNQ OCM pool: 256 KiB @ 0xf0080000
[ 0.259020] bio: create slab <bio-0> at 0
[ 0.260750] vgaarb: loaded
[ 0.261996] SCSI subsystem initialized
[ 0.262885] usbcore: registered new interface driver usbfs
[ 0.263055] usbcore: registered new interface driver hub
[ 0.263298] usbcore: registered new device driver usb
[ 0.263825] media: Linux media interface: v0.10
[ 0.263983] Linux video capture interface: v2.00
[ 0.264226] pps_core: LinuxPPS API ver. 1 registered
[ 0.264238] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.264362] PTP clock support registered
[ 0.264722] EDAC MC: Ver: 3.0.0
[ 0.265784] Advanced Linux Sound Architecture Driver Initialized.
[ 0.268742] DMA-API: preallocated 4096 debug entries
[ 0.268757] DMA-API: debugging enabled by kernel config
[ 0.268846] Switched to clocksource arm_global_timer
[ 0.289841] NET: Registered protocol family 2
[ 0.290522] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.290619] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.290778] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.290853] TCP: reno registered
[ 0.290870] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 0.290928] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 0.291200] NET: Registered protocol family 1
[ 0.291588] RPC: Registered named UNIX socket transport module.
[ 0.291601] RPC: Registered udp transport module.
[ 0.291610] RPC: Registered tcp transport module.
[ 0.291618] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.291632] PCI: CLS 0 bytes, default 64
[ 0.292087] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.294160] futex hash table entries: 512 (order: 3, 32768 bytes)
[ 0.295624] bounce pool size: 64 pages
[ 0.296533] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 0.296750] msgmni has been set to 1487
[ 0.297233] io scheduler noop registered
[ 0.297246] io scheduler deadline registered
[ 0.297284] io scheduler cfq registered (default)
[ 0.307872] dma-pl330 f8003000.ps7-dma: Loaded driver for PL330 DMAC-2364208
[ 0.307892] dma-pl330 f8003000.ps7-dma: DBUFF-128x8bytes Num_Chans-8 Num_Peri-4 Num_Events-16
[ 0.434240] e0001000.serial: ttyPS0 at MMIO 0xe0001000 (irq = 82, base_baud = 3124999) is a xuartps
[ 1.006732] console [ttyPS0] enabled
[ 1.011041] xdevcfg f8007000.ps7-dev-cfg: ioremap 0xf8007000 to f0068000
[ 1.018702] [drm] Initialized drm 1.1.0 20060810
[ 1.035762] brd: module loaded
[ 1.045262] loop: module loaded
[ 1.055033] e1000e: Intel(R) PRO/1000 Network Driver - 2.3.2-k
[ 1.060896] e1000e: Copyright(c) 1999 - 2013 Intel Corporation.
[ 1.068679] libphy: XEMACPS mii bus: probed
[ 1.073088] ------------- phy_id = 0x3625e62
[ 1.077836] xemacps e000b000.ps7-ethernet: pdev->id -1, baseaddr 0xe000b000, irq 54
[ 1.086553] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.093213] ehci-pci: EHCI PCI platform driver
[ 1.100635] zynq-dr e0002000.ps7-usb: Unable to init USB phy, missing?
[ 1.107454] usbcore: registered new interface driver usb-storage
[ 1.114382] mousedev: PS/2 mouse device common for all mice
[ 1.120523] i2c /dev entries driver
[ 1.127428] zynq-edac f8006000.ps7-ddrc: ecc not enabled
[ 1.132972] cpufreq_cpu0: failed to get cpu0 regulator: -19
[ 1.138887] Xilinx Zynq CpuIdle Driver started
[ 1.143745] sdhci: Secure Digital Host Controller Interface driver
[ 1.149888] sdhci: Copyright(c) Pierre Ossman
[ 1.154182] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.161013] mmc0: no vqmmc regulator found
[ 1.165027] mmc0: no vmmc regulator found
[ 1.208883] mmc0: SDHCI controller on e0100000.ps7-sdio [e0100000.ps7-sdio] using ADMA
[ 1.217568] usbcore: registered new interface driver usbhid
[ 1.223088] usbhid: USB HID core driver
[ 1.227834] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xda
[ 1.234126] nand: Micron MT29F2G08ABAEAWP
[ 1.238095] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[ 1.244123] Bad block table found at page 131008, version 0x01
[ 1.250539] Bad block table found at page 130944, version 0x01
[ 1.256683] 4 ofpart partitions found on MTD device pl353-nand
[ 1.262458] Creating 4 MTD partitions on "pl353-nand":
[ 1.267558] 0x000000000000-0x000002000000 : "BOOT.bin-env-dts-kernel"
[ 1.275637] 0x000002000000-0x00000b000000 : "angstram-rootfs"
[ 1.283018] 0x00000b000000-0x00000ec00000 : "upgrade-rootfs"
[ 1.290123] 0x00000ec00000-0x000010000000 : "upgrade-tmp"
[ 1.298798] TCP: cubic registered
[ 1.302069] NET: Registered protocol family 17
[ 1.306715] Registering SWP/SWPB emulation handler
[ 1.312371] regulator-dummy: disabling
[ 1.316176] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 1.326590] ALSA device list:
[ 1.329523] No soundcards found.
[ 5.585234] VFS: Mounted root (jffs2 filesystem) on device 31:1.
[ 5.594255] devtmpfs: mounted
[ 5.597361] Freeing unused kernel memory: 200K (c0676000 - c06a8000)
[ 7.270427] random: dd urandom read with 1 bits of entropy available
[ 7.668870]
[ 7.668870] bcm54xx_config_init
[ 8.278860]
[ 8.278860] bcm54xx_config_init
[ 12.279718] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 12.285828] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 29.888333] In axi fpga driver!
[ 29.891403] request_mem_region OK!
[ 29.894792] AXI fpga dev virtual address is 0xf0112000
[ 29.899938] *base_vir_addr = 0x8c504
[ 29.919501] In fpga mem driver!
[ 29.922573] request_mem_region OK!
[ 29.926139] fpga mem virtual address is 0xf3000000
[ 31.338194]
[ 31.338194] bcm54xx_config_init
[ 31.978093]
[ 31.978093] bcm54xx_config_init
[ 35.978570] xemacps e000b000.ps7-ethernet: Set clk to 124999998 Hz
[ 35.984674] xemacps e000b000.ps7-ethernet: link up (1000/FULL)
[ 84.887577] jffs2: warning: (1095) jffs2_do_read_inode_internal: Truncating ino #2068 to 19073 bytes failed because it only had 16032 bytes to start with!
[ 282.565855] random: nonblocking pool is initialized
use critical mode to search freq...
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check chain[5] PIC fw version=0x02
Check chain[6] PIC fw version=0x02
Check chain[7] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[5] has freq in PIC and will jump over...
Chain[5] has core num in PIC
Chain[5] ASIC[27] has core num=1
Check chain[5] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[6] has freq in PIC and will jump over...
Chain[6] has core num in PIC
Chain[6] ASIC[36] has core num=1
Check chain[6] PIC fw version=0x02
has freq in PIC, will disable freq setting.
chain[7] has freq in PIC and will jump over...
Chain[7] has core num in PIC
Check chain[7] PIC fw version=0x02
get PIC voltage=91 on chain[5], value=890
get PIC voltage=91 on chain[6], value=890
get PIC voltage=108 on chain[7], value=880
chain[5] temp offset record: 62,-4,0,0,0,0,0,0
chain[6] temp offset record: 62,-4,0,0,0,0,0,0
chain[7] temp offset record: 62,-3,0,0,0,0,0,0
set command mode to VIL
singleBoardTest: AsicType = 1387
singleBoardTest: asicNum = 64
singleBoardTest: real AsicNum = 63
--- check asic number
set_baud=0, ought to be 1
The min freq=700
set real timeout 52, need sleep=379392
search freq for 1 times, completed chain = 3, total chain num = 3
disable_pic_dac on chain[5]
disable_pic_dac on chain[6]
disable_pic_dac on chain[7]
restart Miner chance num=2
waiting for send_func to exit of chain[0]
waiting for send_func to exit of chain[1]
waiting for send_func to exit of chain[2]
waiting for send_func to exit of chain[3]
waiting for send_func to exit of chain[4]
waiting for send_func to exit of chain[5]
waiting for send_func to exit of chain[6]
waiting for send_func to exit of chain[7]
waiting for send_func to exit of chain[8]
waiting for send_func to exit of chain[9]
waiting for send_func to exit of chain[10]
waiting for send_func to exit of chain[11]
waiting for send_func to exit of chain[12]
waiting for send_func to exit of chain[13]
waiting for send_func to exit of chain[14]
waiting for send_func to exit of chain[15]
waiting for receive_func to exit!
waiting for pic heart to exit!
Start bmminer ...
This is XILINX board.
Chain[J6] has backup chain_voltage=890
Chain[J6] test patten OK temp=78
Check chain[5] PIC fw version=0x02
Chain[J7] has backup chain_voltage=890
Chain[J7] test patten OK temp=73
Check chain[6] PIC fw version=0x02
Chain[J8] has backup chain_voltage=880
Chain[J8] test patten OK temp=70
Check chain[7] PIC fw version=0x02
Chain[J6] orignal chain_voltage=91 value=890
Chain[J7] orignal chain_voltage=91 value=890
Chain[J8] orignal chain_voltage=108 value=880
Chain[J6] has 63 asic
Chain[J7] has 63 asic
Chain[J8] has 63 asic
Chain[J6] has core num in PIC
Chain[J6] ASIC[27] has core num=1
Chain[J7] has core num in PIC
Chain[J7] ASIC[36] has core num=1
Chain[J8] has core num in PIC
miner total rate=13999GH/s fixed rate=13500GH/s
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:431
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:408 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:662 Asic[48]:662
Asic[49]:662 Asic[50]:662 Asic[51]:662 Asic[52]:662 Asic[53]:662 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:662
Chain:5 max freq=662
Chain:5 min freq=408
read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:656 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:656 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:350 Asic[18]:656 Asic[19]:643 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:512 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:681 Asic[48]:656
Asic[49]:656 Asic[50]:681 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:656 Asic[55]:656 Asic[56]:656
Asic[57]:656 Asic[58]:656 Asic[59]:656 Asic[60]:656 Asic[61]:656 Asic[62]:656
Chain:6 max freq=681
Chain:6 min freq=350
read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:656
Asic[ 1]:656 Asic[ 2]:656 Asic[ 3]:468 Asic[ 4]:656 Asic[ 5]:656 Asic[ 6]:656 Asic[ 7]:656 Asic[ 8]:656
Asic[ 9]:656 Asic[10]:656 Asic[11]:656 Asic[12]:656 Asic[13]:416 Asic[14]:656 Asic[15]:656 Asic[16]:656
Asic[17]:656 Asic[18]:656 Asic[19]:656 Asic[20]:656 Asic[21]:656 Asic[22]:656 Asic[23]:656 Asic[24]:656
Asic[25]:656 Asic[26]:656 Asic[27]:656 Asic[28]:656 Asic[29]:656 Asic[30]:656 Asic[31]:656 Asic[32]:656
Asic[33]:656 Asic[34]:656 Asic[35]:656 Asic[36]:656 Asic[37]:656 Asic[38]:656 Asic[39]:656 Asic[40]:656
Asic[41]:656 Asic[42]:656 Asic[43]:656 Asic[44]:656 Asic[45]:656 Asic[46]:656 Asic[47]:656 Asic[48]:656
Asic[49]:656 Asic[50]:656 Asic[51]:656 Asic[52]:656 Asic[53]:656 Asic[54]:662 Asic[55]:662 Asic[56]:662
Asic[57]:662 Asic[58]:662 Asic[59]:662 Asic[60]:662 Asic[61]:662 Asic[62]:656
Chain:7 max freq=662
Chain:7 min freq=416
Miner fix freq ...
read PIC voltage=890 on chain[5]
Chain:5 chipnum=63
Chain[J6] voltage added=0.0V
OK: Chain[J6] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:5 temp offset=-4
Chain:5 base freq=408
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:431
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:408 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:643 Asic[34]:643 Asic[35]:643 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:5 max freq=643
Chain:5 min freq=408
read PIC voltage=890 on chain[6]
Chain:6 chipnum=63
Chain[J7] voltage added=0.0V
OK: Chain[J7] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:6 temp offset=-4
Chain:6 base freq=350
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:637 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:637 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:350 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:512 Asic[36]:643 Asic[37]:643 Asic[38]:643 Asic[39]:643 Asic[40]:643
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:6 max freq=643
Chain:6 min freq=350
read PIC voltage=880 on chain[7]
Chain:7 chipnum=63
Chain[J8] voltage added=0.2V
OK: Chain[J8] is for this machine! [minerMAC: 38:9a:04:16:3e:b3]
Chain:7 temp offset=-3
Chain:7 base freq=416
Asic[ 0]:637
Asic[ 1]:637 Asic[ 2]:637 Asic[ 3]:468 Asic[ 4]:637 Asic[ 5]:637 Asic[ 6]:637 Asic[ 7]:637 Asic[ 8]:637
Asic[ 9]:637 Asic[10]:637 Asic[11]:637 Asic[12]:637 Asic[13]:416 Asic[14]:637 Asic[15]:637 Asic[16]:637
Asic[17]:637 Asic[18]:637 Asic[19]:637 Asic[20]:637 Asic[21]:637 Asic[22]:637 Asic[23]:637 Asic[24]:637
Asic[25]:637 Asic[26]:637 Asic[27]:637 Asic[28]:637 Asic[29]:637 Asic[30]:637 Asic[31]:637 Asic[32]:637
Asic[33]:637 Asic[34]:637 Asic[35]:637 Asic[36]:637 Asic[37]:637 Asic[38]:637 Asic[39]:637 Asic[40]:637
Asic[41]:643 Asic[42]:643 Asic[43]:643 Asic[44]:643 Asic[45]:643 Asic[46]:643 Asic[47]:643 Asic[48]:643
Asic[49]:643 Asic[50]:643 Asic[51]:643 Asic[52]:643 Asic[53]:643 Asic[54]:643 Asic[55]:643 Asic[56]:643
Asic[57]:643 Asic[58]:643 Asic[59]:643 Asic[60]:643 Asic[61]:643 Asic[62]:643
Chain:7 max freq=643
Chain:7 min freq=416
max freq = 643
Chain[J6] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J6] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J7] PIC temp offset=62,-4,0,0,0,0,0,0
Chain[J7] chip[244] use PIC middle temp offset=-4 typeID=55
Chain[J8] PIC temp offset=62,-3,0,0,0,0,0,0
Chain[J8] chip[244] use PIC middle temp offset=-3 typeID=55
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
Chain[J6] set opencore voltage=920 [40]
Chain[J6] set working voltage=890 [91]
Chain[J7] set opencore voltage=920 [40]
Chain[J7] set working voltage=890 [91]
Chain[J8] set opencore voltage=920 [40]
Chain[J8] set working voltage=880 [108]
prepare send works thread on chain[0]
prepare send works thread on chain[1]
prepare send works thread on chain[2]
prepare send works thread on chain[3]
prepare send works thread on chain[4]
prepare send works thread on chain[5]
prepare send works thread on chain[6]
prepare send works thread on chain[7]
prepare send works thread on chain[8]
prepare send works thread on chain[9]
prepare send works thread on chain[10]
prepare send works thread on chain[11]
prepare send works thread on chain[12]
prepare send works thread on chain[13]
prepare send works thread on chain[14]
prepare send works thread on chain[15]
do heat board 8xPatten for 1 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=911 asic[19]=911 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=911 asic[47]=911
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=911 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[10]=911
core[107]=7
asic[18]=911
core[089]=7
asic[19]=911
core[064]=7
asic[46]=911
core[055]=7
asic[47]=911
core[055]=7
asic[60]=911
core[007]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57450
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:51502
last_nonce_num:35641
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=911 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=911 asic[12]=912 asic[13]=911 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=911 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=911 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=911 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=911 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=911 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[05]=911
core[061]=7
asic[10]=911
core[019]=7
asic[11]=911
core[019]=7
asic[13]=911
core[067]=7
asic[14]=911
core[063]=7
asic[21]=911
core[083]=7
asic[25]=911
core[030]=7
asic[30]=911
core[037]=7
asic[37]=911
core[052]=7
asic[52]=911
core[005]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57446
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44368
last_nonce_num:37018
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=911 asic[15]=912
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=911 asic[20]=911 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=911 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[12]=911
core[092]=7
asic[14]=911
core[094]=7
asic[19]=911
core[057]=7
asic[20]=911
core[053]=7
asic[26]=911
core[035]=7
asic[48]=911
core[040]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57450
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:50456
last_nonce_num:33309
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
do heat board 8xPatten for 2 times
Find hashboard on Chain[5]
Find hashboard on Chain[6]
Find hashboard on Chain[7]
Check voltage total rate=13636
get PIC voltage=890 on chain[5], check: must be < 900
get PIC voltage=890 on chain[6], check: must be < 900
get PIC voltage=880 on chain[7], check: must be < 900
start send works on chain[5]
start send works on chain[6]
start send works on chain[7]
wait send works done on chain[5]
get send work num :57456 on Chain[6]
get send work num :57456 on Chain[7]
get send work num :57456 on Chain[5]
wait send works done on chain[6]
wait send works done on chain[7]
wait recv nonce on chain[5]
wait recv nonce on chain[6]
wait recv nonce on chain[7]
get nonces on chain[5]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=911 asic[11]=912 asic[12]=912 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=911 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[10]=911
core[059]=7
asic[15]=911
core[029]=7
asic[46]=911
core[063]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=431 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=408 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=643 freq[34]=643 freq[35]=643 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57453
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:49422
last_nonce_num:32058
get nonces on chain[6]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=912 asic[02]=912 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=911
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=912 asic[13]=911 asic[14]=912 asic[15]=912
asic[16]=911 asic[17]=912 asic[18]=912 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=911 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=912 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=912 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=911 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[07]=911
core[030]=7
asic[13]=911
core[041]=7
asic[16]=911
core[112]=7
asic[22]=911
core[070]=7
asic[57]=911
core[055]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=637 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=637 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=350 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=512 freq[36]=643 freq[37]=643 freq[38]=643 freq[39]=643
freq[40]=643 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57451
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:50461
last_nonce_num:31431
get nonces on chain[7]
require nonce number:912
require validnonce number:57456
asic[00]=912 asic[01]=911 asic[02]=910 asic[03]=912 asic[04]=912 asic[05]=912 asic[06]=912 asic[07]=912
asic[08]=912 asic[09]=912 asic[10]=912 asic[11]=912 asic[12]=911 asic[13]=912 asic[14]=912 asic[15]=911
asic[16]=912 asic[17]=912 asic[18]=911 asic[19]=912 asic[20]=912 asic[21]=912 asic[22]=912 asic[23]=912
asic[24]=912 asic[25]=912 asic[26]=911 asic[27]=912 asic[28]=912 asic[29]=912 asic[30]=912 asic[31]=912
asic[32]=912 asic[33]=912 asic[34]=912 asic[35]=912 asic[36]=912 asic[37]=912 asic[38]=912 asic[39]=912
asic[40]=912 asic[41]=912 asic[42]=912 asic[43]=912 asic[44]=912 asic[45]=912 asic[46]=912 asic[47]=912
asic[48]=912 asic[49]=912 asic[50]=912 asic[51]=911 asic[52]=912 asic[53]=912 asic[54]=912 asic[55]=912
asic[56]=912 asic[57]=912 asic[58]=912 asic[59]=912 asic[60]=912 asic[61]=912 asic[62]=912
Below ASIC's core didn't receive all the nonce, they should receive 8 nonce each!
asic[01]=911
core[092]=7
asic[02]=910
core[046]=7 core[092]=7
asic[12]=911
core[006]=7
asic[15]=911
core[057]=7
asic[18]=911
core[066]=7
asic[26]=911
core[031]=7
asic[51]=911
core[110]=7
freq[00]=637 freq[01]=637 freq[02]=637 freq[03]=468 freq[04]=637 freq[05]=637 freq[06]=637 freq[07]=637
freq[08]=637 freq[09]=637 freq[10]=637 freq[11]=637 freq[12]=637 freq[13]=416 freq[14]=637 freq[15]=637
freq[16]=637 freq[17]=637 freq[18]=637 freq[19]=637 freq[20]=637 freq[21]=637 freq[22]=637 freq[23]=637
freq[24]=637 freq[25]=637 freq[26]=637 freq[27]=637 freq[28]=637 freq[29]=637 freq[30]=637 freq[31]=637
freq[32]=637 freq[33]=637 freq[34]=637 freq[35]=637 freq[36]=637 freq[37]=637 freq[38]=637 freq[39]=637
freq[40]=637 freq[41]=643 freq[42]=643 freq[43]=643 freq[44]=643 freq[45]=643 freq[46]=643 freq[47]=643
freq[48]=643 freq[49]=643 freq[50]=643 freq[51]=643 freq[52]=643 freq[53]=643 freq[54]=643 freq[55]=643
freq[56]=643 freq[57]=643 freq[58]=643 freq[59]=643 freq[60]=643 freq[61]=643 freq[62]=643
total valid nonce number:57448
total send work number:57456
require valid nonce number:57456
repeated_nonce_num:0
err_nonce_num:44345
last_nonce_num:31732
chain[5]: All chip cores are opened OK!
Test Patten on chain[5]: FAILED!
chain[6]: All chip cores are opened OK!
Test Patten on chain[6]: FAILED!
chain[7]: All chip cores are opened OK!
Test Patten on chain[7]: FAILED!
restartNum = 2 , auto-reinit enabled...
Chain[5] Chip[62] TempTypeID=55 middle offset=-4
Chain[5] Chip[62] local Temp=68
Chain[5] Chip[62] middle Temp=89
Chain[6] Chip[62] TempTypeID=55 middle offset=-4
Chain[6] Chip[62] local Temp=66
Chain[6] Chip[62] middle Temp=86
Chain[7] Chip[62] TempTypeID=55 middle offset=-3
Chain[7] Chip[62] local Temp=66
Chain[7] Chip[62] middle Temp=85
set FAN speed according to: temp_highest=89 temp_top1[PWM_T]=89 temp_top1[TEMP_POS_LOCAL]=68 temp_change=1 fix_fan_steps=3
FAN PWM: 82
okay there are multiple fails. you may have the everything looks good fail all boards have a light but 1 boards does not work fail. if you were on old software you would show say 3 x 4000 = 12000 power would be say 1200 watts but the pools would give you say 2x 4000 = 8000 hash. then in a week or so the board will fully die the little lite on it will vanish and you have the more classic fail. with auto tune you get 0 hash but pull full watts with the 1 dead but shows good board. so pull two cables mine with board A for 4 hours and report back then pull the cable on A add the cable to B mine for four hours report back. then pull the cable on b add the cable to C mine for four hours report back. with luck 2 of your boards will hash. if so then put the cables on both of them and see if you go to 8000 or so., when all is said and done you should or could have 2 working boards. mail the dead one back in. |
|
|
|
HagssFIN
Legendary
Offline
Activity: 2436
Merit: 1706
Electrical engineer. Mining since 2014.
|
|
December 18, 2016, 11:05:46 PM |
|
I now just tried with the PICkit3 to: 1. Read a good PIC firmware from a good hash board 2. Write a good PIC firmware to a dead hash board No effect. The dead hash board is still dead. So it is probably not just "soft bricked". So I wait for the answer from BitmainWarranty ( www.bitmainwarranty.com). I have previous experience with the PICkit3. Do you have the image file from the good hash board? I'd like to have a look at it if you could send it to me. In what way is your board dead? Mine died immediately AFTER a firmware update, it never hashed on the new firmware, so I'm pretty sure it's software related, unless the bad software caused something to overheat. Bitmain thinks it's an incompatible firmware, which is weird because they said it was for "all" but we'll see if they can help me. They responded to my first e-mail and I gave them more information, now I'm waiting to hear back. Thankfully I only flashed one of my S9's, the rest will probably never get a firmware update, it's too risky. Here is the HEX-file PIC16F1704_firmware_good_condition_board_S9_11.85ths_model_non-autotune.hex : https://mega.nz/#!4l8HzB7A!R_Fomh8O5uSk8VVqmRseGduxSbvl_ajDNcATl3z22hAMake sure that you know what you are doing. I take no responsibility on this.My board went dead just suddenly without any warning. |
|
|
|
|
