Pete_X
Jr. Member
Offline
Activity: 47
Merit: 1
|
|
April 07, 2018, 07:30:38 PM |
|
1007h/s Sapp 580 8GB Hynix
Are your hynix is H5GQ8H24MJ ? If yes, what timings are you using for it (and intensity settings for that matter)? I've only managed to push ~840 h/s at 1250 core 2250 mem clocks. Yopp ... MJs. Strap is the normal stuff from PBE 1.6.7. Intensity .. hmmm well depends a lot on the card. Best is between 114 and 125, with Spikes and what not. Best way to find a sweetspot is to see if the hashrate is a flat line or if it goes up n down. Flatline is optimal, Up n Down is close to good Intensity, but not on spot. My card has sweetspots at 114, 117 and 123. Keep in mind, sometimes a reboot is needed to get the real results - specially after some intensive tests
|
|
|
|
CreamyG31337
Member
Offline
Activity: 113
Merit: 10
|
|
April 07, 2018, 08:37:01 PM |
|
tried to see if the cryptonight-heavy would work for me. it doesn't. i can't adjust the settings because it just stupidly tries to run the previous settings that crashed every time i open it now.
|
BTC tip jar: bc1qtepyll2c9fkn67wpnhunclw4mf39nc2jx79zdh
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
April 07, 2018, 08:44:17 PM |
|
tried to see if the cryptonight-heavy would work for me. it doesn't. i can't adjust the settings because it just stupidly tries to run the previous settings that crashed every time i open it now.
That is by design, too. GGS was trying to measure the success rate by repeating trials with the same settings. If you don't want this particular behavior, you can just check "Do not repeat after failure."
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
Elder III
|
|
April 07, 2018, 08:52:13 PM |
|
I'm looking forward to seeing what you can do with this. Let us know if you need any guinea pigs for stability testing. I can have either R9 Fury series, Rx 400 series, or Rx 500 series do a little testing if that's of any help to you.
|
|
|
|
human75
Newbie
Offline
Activity: 51
Merit: 0
|
|
April 07, 2018, 08:58:28 PM |
|
Hi.Can someone please help me for MININGPOOL hub custom settings as a custom pool?how can i make it work?many thx
|
|
|
|
murgorx
Member
Offline
Activity: 443
Merit: 13
|
|
April 07, 2018, 09:36:31 PM |
|
The miner has been running really, really stable for the past 3-4 hours, I even worked a bit on the rig, so there were other processes as well, but will see until the first 24 hours. Incredible performance until now, gg
|
|
|
|
nitrobg
Member
Offline
Activity: 413
Merit: 17
|
|
April 08, 2018, 10:13:29 AM |
|
X16R sound like a good idea. RX 580 should outperform GTX 1060 by a large margin, at least. Let me see...
Unfortunately, the RX 580 @ 1250 core and 1000mV voltage does about 4.5MH/s, which is around 1050Ti levels but on ~120W power draw. If you can somehow manage to match or even pass 1060's levels, you will attract a huge mount of users. What about a standalone X17 kernel? The only difference between the algos in X16r and X17 is djb2. The only available kernel is unfortunately very old and barely working.
|
|
|
|
skablast
Member
Offline
Activity: 476
Merit: 19
|
|
April 08, 2018, 11:03:08 AM |
|
@Nitrobg. Go stock, acefawn sg-miner and then tweak sg parameter. I got 7.x . Average, I mean
|
|
|
|
UnclWish
|
|
April 08, 2018, 11:09:57 AM Last edit: April 08, 2018, 11:31:26 AM by UnclWish |
|
My observations: 1. Pitcairn cryptonight kernel issue is still there - with it GGS make only 515-520 h/s. Without kernel GGS gives 525-535 h/s. Claymore's 11.3 (without fee!) gives 550 h/s. 2. After enabling overclock settings on Pitcairn GPU and starting GGS it just give BSOD THREAD_STUCK_IN_DEVICE_DRIVER. Like it was in previous versions of GGS. 3. GGS starting take more time than <1.3 versions. 4. Can't put all timings from strap into they fields on GGS. You must make possibility to parsing straps from entire string. 5. In 1.2.x versions with my GPU OC settings GGS works stable. With the same settings but cryptonight V7 GGS sometimes (hour or two) drops to BSOD THREAD_STUCK_IN_DEVICE_DRIVER. 6. For apllaying timings it's need to enable phymem? 7. If not for what phymem is needed? 8. Minimal fan speed is 20%. Why? Miminal speed must be 0%.
Cryptonight V7 needs other overclock settings? Especcially voltages? Does it need more GPU power? Or something else? Intensity for V7 differes from CN or it the same?
Thanks for your work! Hope you continue your hard work. We all are very GREATFULL to You!
|
|
|
|
UnclWish
|
|
April 08, 2018, 11:34:20 AM |
|
Ohhh. Only now noticed:
GGS use 10-15% of CPU power during nicehash cryptonight v7 mining if enabled overclock for RX 580 cards in GGS! It's too high!
|
|
|
|
Zhantik
Newbie
Offline
Activity: 1
Merit: 0
|
|
April 08, 2018, 11:46:56 AM |
|
Good day! Prompt when there will be a usual version as earlier without installation, support of V7, V3, as before, with support for edit bat of the file? sorry for my English.
|
|
|
|
hamesh
Newbie
Offline
Activity: 22
Merit: 0
|
|
April 08, 2018, 06:49:39 PM |
|
How does one specify Cryptonight v7? I keep getting rejected shares as seems to be switching/selecting v3 and can't find documentation around designating version to use for a given pool: 2018-04-08 12:46:53.2386 [9] Built cryptonight program for Device #0. 2018-04-08 12:46:53.2386 [9] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-08 12:46:53.2386 [9] Switching to Monero Version 3 2018-04-08 12:46:54.8505 [19] Device #0 (CryptoNight): 420.74 h/s 2018-04-08 12:46:55.2617 [24] Device #1 (CryptoNight): 406.40 h/s 2018-04-08 12:46:55.3351 [23] Device #1 (CryptoNight): 406.35 h/s 2018-04-08 12:47:02.0377 [24] Device #1 submitted Share #0 to communitypool.stellite.cash as Se2xy7zgW.... 2018-04-08 12:47:02.0377 [24] Device #1 submitted a share to communitypool.stellite.cash as Se2xy7zgW.... 2018-04-08 12:47:02.2422 [20] Received new job: FkGgg0m47P7X598ydv/MJKX8iwYO 2018-04-08 12:47:02.4627 [20] Share #0 rejected: Low difficulty share Claymore's CryptoNote AMD GPU Miner v11.3 works via the -pow7 switch.
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
April 08, 2018, 08:20:59 PM |
|
How does one specify Cryptonight v7? I keep getting rejected shares as seems to be switching/selecting v3 and can't find documentation around designating version to use for a given pool: 2018-04-08 12:46:53.2386 [9] Built cryptonight program for Device #0. 2018-04-08 12:46:53.2386 [9] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-08 12:46:53.2386 [9] Switching to Monero Version 3 2018-04-08 12:46:54.8505 [19] Device #0 (CryptoNight): 420.74 h/s 2018-04-08 12:46:55.2617 [24] Device #1 (CryptoNight): 406.40 h/s 2018-04-08 12:46:55.3351 [23] Device #1 (CryptoNight): 406.35 h/s 2018-04-08 12:47:02.0377 [24] Device #1 submitted Share #0 to communitypool.stellite.cash as Se2xy7zgW.... 2018-04-08 12:47:02.0377 [24] Device #1 submitted a share to communitypool.stellite.cash as Se2xy7zgW.... 2018-04-08 12:47:02.2422 [20] Received new job: FkGgg0m47P7X598ydv/MJKX8iwYO 2018-04-08 12:47:02.4627 [20] Share #0 rejected: Low difficulty share Claymore's CryptoNote AMD GPU Miner v11.3 works via the -pow7 switch. I will add an option to force CryptoNightV7.
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
April 09, 2018, 06:51:39 AM |
|
So I spent the whole Sunday on X16R, and it's finally working. Not bad as a first attempt, but there seems to be a HUGE room for optimizations. My wife is really pissed off, but that's OK...
|
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ
|
|
|
murgorx
Member
Offline
Activity: 443
Merit: 13
|
|
April 09, 2018, 06:59:48 AM Last edit: April 09, 2018, 08:28:52 AM by murgorx |
|
Nice work Zawawa! With which version will we be able to try it out, or you want to optimize it first and you will release it afterwards. X16r is really booming atm, keeping up to date with the trends is what will make your miner one of the most used! Congratz for the great and constant work!
EDIT: mining @ 1240/2200 with cvddc and mvddc@900 with 550W, 42celsius for 2 days straight, each card hashing 900! Superb results!
|
|
|
|
Branko
|
|
April 09, 2018, 09:29:51 AM |
|
Is it preferred to use stock BIOSes with this miner now?
|
|
|
|
RIGED
Member
Offline
Activity: 182
Merit: 12
|
|
April 09, 2018, 09:37:25 AM |
|
late to the party...
please point to the download link of the Cryptonight heavy version, is it on pg1 first post?
what do I have to do, to get the 6 Vega 64 running close to 2KH/s as with other miners?
Thank you for the effort!!
|
to mine or not to mine, is not a question...
|
|
|
skablast
Member
Offline
Activity: 476
Merit: 19
|
|
April 09, 2018, 09:48:18 AM |
|
@Branko, actually I am using your bios mod for RX 550 4g ...and its giving 535 h/s on cryptonight. Thanks, btw. I changed timing on the fly with GGS. Zawawa, stop playing with the new toy! and finish with the old one in order that WE can play with it. Cryptonightv7 isn't exactly stable,in fact GGS restart on its own each 3 hour, ( and btw, keep working so mining is ok). Cryptonight v7 Monero Graft, Stellite ... Cryptonight Heavy but what about Cryptonight Litev7 Cryptonight UltraHeavy ? And it take too much memory... Last, very good job on the x16r . Still to beat my 7.4 Mhs for an rx 580... it will take a couple of days for you
|
|
|
|
Branko
|
|
April 09, 2018, 09:53:09 AM |
|
@Branko, actually I am using your bios mod for RX 550 4g ...and its giving 535 h/s on cryptonight. Thanks, btw. I changed timing on the fly with GGS. Zawawa, stop playing with the new toy! and finish with the old one in order that WE can play with it. Cryptonightv7 isn't exactly stable,in fact GGS restart on its own each 3 hour, ( and btw, keep working so mining is ok). Cryptonight v7 Monero Graft, Stellite ... Cryptonight Heavy but what about Cryptonight Litev7 Cryptonight UltraHeavy ? And it take too much memory... Last, very good job on the x16r . Still to beat my 7.4 Mhs for an rx 580... it will take a couple of days for you So GGS is not autotuning, but let you choose strap manually? That would make it great tool for testing straps, I guess I'll have to try it out
|
|
|
|
inv1s1bl3
Newbie
Offline
Activity: 65
Merit: 0
|
|
April 09, 2018, 01:08:41 PM |
|
Hello, I wanted to try the cryptonight-heavy, but after it loads I receive the error message, that the intensity is set too high for a certain GPU and it stops mining. Here is the log: 2018-04-09 16:02:28.4923 [1] Gateless Gate Sharp 1.3.2 prealpha started. 2018-04-09 16:02:29.4194 [1] Number of Devices: 5 2018-04-09 16:02:29.5206 [1] Successfully initialized AMD Display Library. 2018-04-09 16:02:29.5206 [1] Number of ADL Adapters: 80 2018-04-09 16:02:30.1731 [1] ADL_Adapter_AdapterInfo_Get() returned error code 0 2018-04-09 16:02:30.1741 [1] Failed to initialize NVIDIA Management Library. 2018-04-09 16:02:30.1842 [1] Exception in UpdateControls(): The given key was not present in the dictionary. at System.ThrowHelper.ThrowKeyNotFoundException() at System.Collections.Generic.Dictionary`2.get_Item(TKey key) at GatelessGateSharp.MainForm.UpdateControls() 2018-04-09 16:02:41.7731 [1] Loading settings from C:\Users\Alexander\AppData\Roaming\GatelessGateSharp\GatelessGateSharp.sqlite... 2018-04-09 16:02:46.6170 [1] Loaded settings. 2018-04-09 16:02:46.6235 [1] Invalid argument: C:\Program Files\Zawawa Software LLC\Gateless Gate Sharp\GatelessGateSharp.exe 2018-04-09 16:02:50.3648 [1] Launching miner(s) for Custom Pool 2... 2018-04-09 16:02:50.6866 [13] Miner thread for Device #0 started. 2018-04-09 16:02:50.6866 [13] NiceHash mode is off. 2018-04-09 16:02:50.7107 [13] Loaded Kernels\cryptonight_heavy.cl for Device #0. 2018-04-09 16:02:50.8115 [14] Miner thread for Device #0 started. 2018-04-09 16:02:50.8115 [14] NiceHash mode is off. 2018-04-09 16:02:50.8125 [14] Loaded Kernels\cryptonight_heavy.cl for Device #0. 2018-04-09 16:02:58.0873 [4] Miner thread for Device #1 started. 2018-04-09 16:02:58.0873 [4] NiceHash mode is off. 2018-04-09 16:02:58.0878 [13] Built cryptonight_heavy program for Device #0. 2018-04-09 16:02:58.0878 [13] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-09 16:02:58.0908 [4] Loaded Kernels\cryptonight_heavy.cl for Device #1. 2018-04-09 16:02:58.2367 [16] Miner thread for Device #1 started. 2018-04-09 16:02:58.2367 [16] NiceHash mode is off. 2018-04-09 16:02:58.2392 [16] Loaded Kernels\cryptonight_heavy.cl for Device #1. 2018-04-09 16:03:03.1779 [18] Running garbage collection... 2018-04-09 16:03:03.1779 [18] Memory used before collection: 18MB 2018-04-09 16:03:05.1762 [20] Miner thread for Device #2 started. 2018-04-09 16:03:05.1762 [20] NiceHash mode is off. 2018-04-09 16:03:05.1812 [14] Built cryptonight_heavy program for Device #0. 2018-04-09 16:03:05.1812 [14] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-09 16:03:05.1973 [20] Loaded Kernels\cryptonight_heavy.cl for Device #2. 2018-04-09 16:03:05.1978 [18] Memory used before collection: 14MB 2018-04-09 16:03:05.3336 [21] Miner thread for Device #2 started. 2018-04-09 16:03:05.3336 [21] NiceHash mode is off. 2018-04-09 16:03:05.3371 [21] Loaded Kernels\cryptonight_heavy.cl for Device #2. 2018-04-09 16:03:12.5648 [22] Miner thread for Device #3 started. 2018-04-09 16:03:12.5648 [22] NiceHash mode is off. 2018-04-09 16:03:12.5653 [16] Built cryptonight_heavy program for Device #1. 2018-04-09 16:03:12.5653 [16] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-09 16:03:12.5673 [22] Loaded Kernels\cryptonight_heavy.cl for Device #3. 2018-04-09 16:03:12.7077 [23] Miner thread for Device #3 started. 2018-04-09 16:03:12.7077 [23] NiceHash mode is off. 2018-04-09 16:03:12.7082 [23] Loaded Kernels\cryptonight_heavy.cl for Device #3. 2018-04-09 16:03:13.6813 [24] API Listener started. 2018-04-09 16:03:19.8342 [25] Miner thread for Device #4 started. 2018-04-09 16:03:19.8342 [25] NiceHash mode is off. 2018-04-09 16:03:19.8352 [21] Built cryptonight_heavy program for Device #2. 2018-04-09 16:03:19.8352 [21] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-09 16:03:19.8362 [25] Loaded Kernels\cryptonight_heavy.cl for Device #4. 2018-04-09 16:03:19.9770 [26] Miner thread for Device #4 started. 2018-04-09 16:03:19.9775 [26] NiceHash mode is off. 2018-04-09 16:03:19.9811 [26] Loaded Kernels\cryptonight_heavy.cl for Device #4. 2018-04-09 16:03:20.0918 [1] Stopping miners... 2018-04-09 16:03:27.0102 [23] Built cryptonight_heavy program for Device #3. 2018-04-09 16:03:27.0102 [23] Build options: -O5 -IKernels -DWORKSIZE=8 2018-04-09 16:03:30.8820 [1] Stopped miners. 2018-04-09 16:03:34.2725 [26] 2018-04-09 16:03:40.9390 [25] 2018-04-09 16:03:47.4238 [22] 2018-04-09 16:03:54.4827 [20] 2018-04-09 16:04:01.7410 [4]
Could anyone say what's up and what exactly is needed to make it work ?
|
|
|
|
|