Bitcoin Forum
June 21, 2024, 08:27:06 AM *
News: Latest Bitcoin Core release: 27.0 [Torrent]
 
   Home   Help Search Login Register More  
Poll
Question: What feature you want to see next?
auto tune each mining board - 45 (35.7%)
3 profile switch support (low noise, normal, high performance mode) - 13 (10.3%)
day / night speed schedule - 10 (7.9%)
pool balance / quota option - 9 (7.1%)
v2 configurable reboot on low hashrate / HW errors - 16 (12.7%)
DONE: cgminer v4.10 update - 4 (3.2%)
miner shutdown (+ on high temps) - 11 (8.7%)
better pool management - 9 (7.1%)
DONE:better awesome miner compatibility - 3 (2.4%)
move FAN settings to advanced page - 2 (1.6%)
<your idea> - 4 (3.2%)
Total Voters: 126

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 [26] 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 ... 126 »
  Print  
Author Topic: Antminer D3 Blissz firmware (10/12 v1.12 update)  (Read 125827 times)
blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 06:41:08 PM
Last edit: November 20, 2017, 07:38:07 PM by blissz
 #501

-
PsKminer
Member
**
Offline Offline

Activity: 118
Merit: 11


View Profile
November 20, 2017, 06:45:13 PM
 #502

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.
blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 06:46:58 PM
 #503

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%
cryptonitro
Full Member
***
Offline Offline

Activity: 348
Merit: 119



View Profile
November 20, 2017, 07:01:34 PM
 #504

have an issue , i set 25% before flash , seem to can't change it to lower then, webpage locked to "Waiting for changes to be applied..."
Seem to be global miner general configuration page
anyone same ?
try to change pool or just fan speed

advanced settings working good

The only project make me believe ... Holochain
PsKminer
Member
**
Offline Offline

Activity: 118
Merit: 11


View Profile
November 20, 2017, 07:04:28 PM
 #505

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.

The issue is only in the "General Settings" page.

blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 07:07:59 PM
 #506

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?
cryptonitro
Full Member
***
Offline Offline

Activity: 348
Merit: 119



View Profile
November 20, 2017, 07:10:06 PM
 #507

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?

yep and tried with an other one ,same issue , i tried remotly with my smartphone (port forward) same bug, nothing writen and miner do not reboot

The only project make me believe ... Holochain
PsKminer
Member
**
Offline Offline

Activity: 118
Merit: 11


View Profile
November 20, 2017, 07:11:25 PM
 #508

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?

Yes, first i've tried to CTRL+F5 to reload the website, that will be enough but i've tried cleaning cache, nothing changes. Thanks for your great work.
blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 07:18:58 PM
 #509

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?

Yes, first i've tried to CTRL+F5 to reload the website, that will be enough but i've tried cleaning cache, nothing changes. Thanks for your great work.

strange stuff, I flashed back to stock and upgraded, but don't see the issue. Can you tell me step by step what you do and what is working / what is not. Thank you!

edit: nevermind I see the issue. The advanced page is ok, but changing the fan doesn't work. Thank you for the fast response! I am going to fix it
Maicol792
Legendary
*
Offline Offline

Activity: 1260
Merit: 1010


View Profile
November 20, 2017, 07:20:43 PM
 #510

This is the file cgminer.sh in the image on the D3:

Code:
#!/bin/sh

PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
DAEMON=/usr/bin/cgminer
NAME=cgminer
DESC="Cgminer daemon"

set -e
#set -x
test -x "$DAEMON" || exit 0

#echo "" /var/log/messages

# DASH miner

# PLUG0: GPIO1_19: GPIO51
# PLUG1: GPIO1_16: GPIO48
# PLUG2: GPIO1_15: GPIO47
# PLUG3: GPIO1_12: GPIO44
if [ ! -d /sys/class/gpio/gpio51 ]; then
    echo 51 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio51/direction
fi
if [ ! -d /sys/class/gpio/gpio48 ]; then
    echo 48 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio48/direction
fi
if [ ! -d /sys/class/gpio/gpio47 ]; then
    echo 47 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio47/direction
fi
if [ ! -d /sys/class/gpio/gpio44 ]; then
    echo 44 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio44/direction
fi

# RST0: GPIO0_5:  GPIO5
# RST1: GPIO0_4:  GPIO4
# RST2: GPIO0_27: GPIO27
# RST3: GPIO0_22: GPIO22
if [ ! -d /sys/class/gpio/gpio5 ]; then
    echo 5 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio5/direction
    echo 1 > /sys/class/gpio/gpio5/value
fi
if [ ! -d /sys/class/gpio/gpio4 ]; then
    echo 4 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio4/direction
    echo 1 > /sys/class/gpio/gpio4/value
fi
if [ ! -d /sys/class/gpio/gpio27 ]; then
    echo 27 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio27/direction
    echo 1 > /sys/class/gpio/gpio27/value
fi
if [ ! -d /sys/class/gpio/gpio22 ]; then
    echo 22 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio22/direction
    echo 1 > /sys/class/gpio/gpio22/value
fi

# BEEP: GPIO0_20: GPIO20
if [ ! -d /sys/class/gpio/gpio20 ]; then
    echo 20 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio20/direction
    echo 0 > /sys/class/gpio/gpio20/value
fi

# RED LED: GPIO1_13: GPIO45
if [ ! -d /sys/class/gpio/gpio45 ]; then
    echo 45 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio45/direction
    echo 0 > /sys/class/gpio/gpio45/value
fi

# GREEN LED: GPIO0_23: GPIO23
if [ ! -d /sys/class/gpio/gpio23 ]; then
    echo 23 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio23/direction
    echo 0 > /sys/class/gpio/gpio23/value
fi

# FAN_SPEED0: GPIO3_16: GPIO112
if [ ! -d /sys/class/gpio/gpio112 ]; then
    echo 112 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio112/direction
    echo falling > /sys/class/gpio/gpio112/edge
fi

# FAN_SPEED1: GPIO3_14: GPIO110
if [ ! -d /sys/class/gpio/gpio110 ]; then
    echo 110 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio110/direction
    echo falling > /sys/class/gpio/gpio110/edge
fi

# FAN_PWM: GPIO3_15: P9_29: EHRPWMoB
if [ ! -d /sys/class/pwm/pwm1 ]; then
    echo 1 > /sys/class/pwm/export
    echo 100000 > /sys/class/pwm/pwm1/period_ns
    echo 50000 > /sys/class/pwm/pwm1/duty_ns
    echo 1 > /sys/class/pwm/pwm1/run
fi

do_start() {

NIC=eth0
MAC=`LANG=C ifconfig $NIC | awk '/HWaddr/{ print $5 }'`
#echo $MAC | tr '[a-z]' '[A-Z]'
upmac=`echo $MAC | tr '[a-z]' '[A-Z]'`
#echo $upmac
curti=`date "+%Y-%m-%d %H:%M:%S"`
#echo $curti

OUTPUT=/tmp/pic_mac
echo "${upmac:0:2}"" ${curti:2:2}" > $OUTPUT
echo "${upmac:3:2}"" ${curti:5:2}" >> $OUTPUT
echo "${upmac:6:2}"" ${curti:8:2}" >> $OUTPUT
echo "${upmac:9:2}"" ${curti:11:2}" >> $OUTPUT
echo "${upmac:12:2}"" ${curti:14:2}" >> $OUTPUT
echo "${upmac:15:2}"" ${curti:17:2}" >> $OUTPUT

# check network state
#network_ok=`ping -c 1 114.114.114.114 | grep " 0% packet loss" | wc -l`
#if [ $network_ok -eq 0 ];then
#    return
#fi

# gpio1_16 = 48 = net check LED
#if [ ! -e /sys/class/gpio/gpio48 ]; then
# echo 48 > /sys/class/gpio/export
#fi
#echo low > /sys/class/gpio/gpio48/direction

gateway=$(route -n | grep 'UG[ \t]' | awk '{print $2}')
if [ x"" == x"$gateway" ]; then
gateway="192.168.1.1"
fi
if [ "`ping -w 1 -c 1 $gateway | grep "100%" >/dev/null`" ]; then                                                  
prs=1                                                
echo "$gateway is Not reachable"                            
else                                              
   prs=0
echo "$gateway is reachable"
fi                    


PARAMS="--version-file /usr/bin/compile_time --default-config /config/cgminer.conf -T --syslog"
echo PARAMS = $PARAMS
start-stop-daemon -b -S -x screen -- -S cgminer -t cgminer -m -d "$DAEMON" $PARAMS  
#cgminer $PARAMS -D --api-listen --default-config /config/cgminer.conf 2>&1 | tee log
}

do_stop() {
        killall -9 cgminer || true
}
case "$1" in
  start)
        echo -n "Starting $DESC: "
do_start
        echo "$NAME."
        ;;
  stop)
        echo -n "Stopping $DESC: "
do_stop
        echo "$NAME."
        ;;
  restart|force-reload)
        echo -n "Restarting $DESC: "
        do_stop
        do_start
        echo "$NAME."
        ;;
  *)
        N=/etc/init.d/$NAME
        echo "Usage: $N {start|stop|restart|force-reload}" >&2
        exit 1
        ;;
esac

exit 0


where is the "command" for select algo for mining start or where we can change the algo round for select another of 11 round set?
cryptonitro
Full Member
***
Offline Offline

Activity: 348
Merit: 119



View Profile
November 20, 2017, 07:39:34 PM
 #511

how many errors/hour are acceptable? I´m always getting errors at all frequencies and all voltages.

HW errors: I would say max 10 an hour is ok.
Discarded shares: I get them all the time, but don't bother looking at them.
Rejected shared: below 1%

Ok thanks!.

In the new version, when click "Apply".... nothing applies, i've started at 25% fan speed and 400mhz and I can't change the fan speed, all the chips at 90º degrees, i had to power off the machine and install the original version to set it a 70% and then install your firmware again. After a few tests nothing changes clicking apply, be careful with that.



Thank you for the feedback. Did you clear your browser cache?

Yes, first i've tried to CTRL+F5 to reload the website, that will be enough but i've tried cleaning cache, nothing changes. Thanks for your great work.

strange stuff, I flashed back to stock and upgraded, but don't see the issue. Can you tell me step by step what you do and what is working / what is not. Thank you!

edit: nevermind I see the issue. The advanced page is ok, but changing the fan doesn't work. Thank you for the fast response! I am going to fix it
yep changing fans and pool setting to

The only project make me believe ... Holochain
blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 07:41:02 PM
 #512


yep changing fans and pool setting to

I'm on it Smiley
crackfoo
Legendary
*
Offline Offline

Activity: 3500
Merit: 1126



View Profile WWW
November 20, 2017, 07:45:52 PM
 #513

thanks, I've no problems at all with your latest update.

ZPOOL - the miners multipool! Support We pay 10 FLUX Parallel Assets (PA) directly to block rewards! Get paid more and faster. No PA fee's or waiting around for them, paid instantly on every block found!
mcan
Member
**
Offline Offline

Activity: 70
Merit: 10


View Profile
November 20, 2017, 07:51:49 PM
 #514


yep changing fans and pool setting to

I'm on it Smiley
Which tool do you use to unpack initramfs.bin.sd in windows 10?
may142012
Member
**
Offline Offline

Activity: 301
Merit: 10


View Profile
November 20, 2017, 07:52:07 PM
 #515

thanks, I've no problems at all with your latest update.

Hey, how is your hidden 20% fees? You think we are fools? Stop promoting you schemes, no one want to use your pool.
crackfoo
Legendary
*
Offline Offline

Activity: 3500
Merit: 1126



View Profile WWW
November 20, 2017, 07:57:24 PM
 #516

thanks, I've no problems at all with your latest update.

Hey, how is your hidden 20% fees? You think we are fools? Stop promoting you schemes, no one want to use your pool.

it's 100% now. No one gets paid. They all donate 'cause they love me. All 10k of them.

Stay on topic you twat.

cheers

ZPOOL - the miners multipool! Support We pay 10 FLUX Parallel Assets (PA) directly to block rewards! Get paid more and faster. No PA fee's or waiting around for them, paid instantly on every block found!
taserz
Sr. Member
****
Offline Offline

Activity: 800
Merit: 293


Created AutoTune to saved the planet! ~USA


View Profile
November 20, 2017, 08:02:16 PM
 #517

This is the file cgminer.sh in the image on the D3:

Code:
#!/bin/sh

PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin
DAEMON=/usr/bin/cgminer
NAME=cgminer
DESC="Cgminer daemon"

set -e
#set -x
test -x "$DAEMON" || exit 0

#echo "" /var/log/messages

# DASH miner

# PLUG0: GPIO1_19: GPIO51
# PLUG1: GPIO1_16: GPIO48
# PLUG2: GPIO1_15: GPIO47
# PLUG3: GPIO1_12: GPIO44
if [ ! -d /sys/class/gpio/gpio51 ]; then
    echo 51 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio51/direction
fi
if [ ! -d /sys/class/gpio/gpio48 ]; then
    echo 48 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio48/direction
fi
if [ ! -d /sys/class/gpio/gpio47 ]; then
    echo 47 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio47/direction
fi
if [ ! -d /sys/class/gpio/gpio44 ]; then
    echo 44 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio44/direction
fi

# RST0: GPIO0_5:  GPIO5
# RST1: GPIO0_4:  GPIO4
# RST2: GPIO0_27: GPIO27
# RST3: GPIO0_22: GPIO22
if [ ! -d /sys/class/gpio/gpio5 ]; then
    echo 5 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio5/direction
    echo 1 > /sys/class/gpio/gpio5/value
fi
if [ ! -d /sys/class/gpio/gpio4 ]; then
    echo 4 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio4/direction
    echo 1 > /sys/class/gpio/gpio4/value
fi
if [ ! -d /sys/class/gpio/gpio27 ]; then
    echo 27 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio27/direction
    echo 1 > /sys/class/gpio/gpio27/value
fi
if [ ! -d /sys/class/gpio/gpio22 ]; then
    echo 22 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio22/direction
    echo 1 > /sys/class/gpio/gpio22/value
fi

# BEEP: GPIO0_20: GPIO20
if [ ! -d /sys/class/gpio/gpio20 ]; then
    echo 20 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio20/direction
    echo 0 > /sys/class/gpio/gpio20/value
fi

# RED LED: GPIO1_13: GPIO45
if [ ! -d /sys/class/gpio/gpio45 ]; then
    echo 45 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio45/direction
    echo 0 > /sys/class/gpio/gpio45/value
fi

# GREEN LED: GPIO0_23: GPIO23
if [ ! -d /sys/class/gpio/gpio23 ]; then
    echo 23 > /sys/class/gpio/export
    echo out > /sys/class/gpio/gpio23/direction
    echo 0 > /sys/class/gpio/gpio23/value
fi

# FAN_SPEED0: GPIO3_16: GPIO112
if [ ! -d /sys/class/gpio/gpio112 ]; then
    echo 112 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio112/direction
    echo falling > /sys/class/gpio/gpio112/edge
fi

# FAN_SPEED1: GPIO3_14: GPIO110
if [ ! -d /sys/class/gpio/gpio110 ]; then
    echo 110 > /sys/class/gpio/export
    echo in > /sys/class/gpio/gpio110/direction
    echo falling > /sys/class/gpio/gpio110/edge
fi

# FAN_PWM: GPIO3_15: P9_29: EHRPWMoB
if [ ! -d /sys/class/pwm/pwm1 ]; then
    echo 1 > /sys/class/pwm/export
    echo 100000 > /sys/class/pwm/pwm1/period_ns
    echo 50000 > /sys/class/pwm/pwm1/duty_ns
    echo 1 > /sys/class/pwm/pwm1/run
fi

do_start() {

NIC=eth0
MAC=`LANG=C ifconfig $NIC | awk '/HWaddr/{ print $5 }'`
#echo $MAC | tr '[a-z]' '[A-Z]'
upmac=`echo $MAC | tr '[a-z]' '[A-Z]'`
#echo $upmac
curti=`date "+%Y-%m-%d %H:%M:%S"`
#echo $curti

OUTPUT=/tmp/pic_mac
echo "${upmac:0:2}"" ${curti:2:2}" > $OUTPUT
echo "${upmac:3:2}"" ${curti:5:2}" >> $OUTPUT
echo "${upmac:6:2}"" ${curti:8:2}" >> $OUTPUT
echo "${upmac:9:2}"" ${curti:11:2}" >> $OUTPUT
echo "${upmac:12:2}"" ${curti:14:2}" >> $OUTPUT
echo "${upmac:15:2}"" ${curti:17:2}" >> $OUTPUT

# check network state
#network_ok=`ping -c 1 114.114.114.114 | grep " 0% packet loss" | wc -l`
#if [ $network_ok -eq 0 ];then
#    return
#fi

# gpio1_16 = 48 = net check LED
#if [ ! -e /sys/class/gpio/gpio48 ]; then
# echo 48 > /sys/class/gpio/export
#fi
#echo low > /sys/class/gpio/gpio48/direction

gateway=$(route -n | grep 'UG[ \t]' | awk '{print $2}')
if [ x"" == x"$gateway" ]; then
gateway="192.168.1.1"
fi
if [ "`ping -w 1 -c 1 $gateway | grep "100%" >/dev/null`" ]; then                                                  
prs=1                                                
echo "$gateway is Not reachable"                            
else                                              
   prs=0
echo "$gateway is reachable"
fi                    


PARAMS="--version-file /usr/bin/compile_time --default-config /config/cgminer.conf -T --syslog"
echo PARAMS = $PARAMS
start-stop-daemon -b -S -x screen -- -S cgminer -t cgminer -m -d "$DAEMON" $PARAMS  
#cgminer $PARAMS -D --api-listen --default-config /config/cgminer.conf 2>&1 | tee log
}

do_stop() {
        killall -9 cgminer || true
}
case "$1" in
  start)
        echo -n "Starting $DESC: "
do_start
        echo "$NAME."
        ;;
  stop)
        echo -n "Stopping $DESC: "
do_stop
        echo "$NAME."
        ;;
  restart|force-reload)
        echo -n "Restarting $DESC: "
        do_stop
        do_start
        echo "$NAME."
        ;;
  *)
        N=/etc/init.d/$NAME
        echo "Usage: $N {start|stop|restart|force-reload}" >&2
        exit 1
        ;;
esac

exit 0


where is the "command" for select algo for mining start or where we can change the algo round for select another of 11 round set?

Hence only mines x11 coins...

Autotune Firmware for S19 and S19j! Overclock, Underclock, AutoTuning. Asic.to The MOON Increased hashrate, improved power efficiency 30w/TH up to 85th/s!!Mining bitcoin since 2011 • Best nerd decision of my life
cryptonitro
Full Member
***
Offline Offline

Activity: 348
Merit: 119



View Profile
November 20, 2017, 08:03:45 PM
 #518


yep changing fans and pool setting to

I'm on it Smiley
Which tool do you use to unpack initramfs.bin.sd in windows 10?

man stop asking question to remove the fee & else , you are spotted , i cant understand why you have again answers.

The only project make me believe ... Holochain
blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 08:12:45 PM
 #519

20/11 recommended UPDATE



https://mega.nz/#!ngwhgaBS!bflAJghChk1pOMtWIyjmzFi7a9UNM7Itz4VkvYcnMq0

Changes 20/11:
- ASIC frequency adjustable per chain
- Voltage settings adjustable per chain
- new graphics. (You might need to clear your browser cache)
- Switching pools overhead lowered (now mines for fee every 2 hours).


know issues:

- when using the AUTO fan profile, the fan starts at a too high RPM after powering up.
- switching pools can sometimes cause the miner to wait for work for 10 seconds.

when you can't change the fan / pool settings:
Please download and flash again as the first link to this version doesn't allow changing the fan speed. Sorry for the inconvenience.
blissz (OP)
Sr. Member
****
Offline Offline

Activity: 336
Merit: 258


View Profile
November 20, 2017, 08:15:32 PM
 #520

sorry for the issue in the first upload, this should solve the issues. Thanks for the fast reaction time

Everybody that already "work" on the first uploaded 20/11 version, please upgrade again, as you won't be able to adjust the pools / fan speeds
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 [26] 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 ... 126 »
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2006-2009, Simple Machines Valid XHTML 1.0! Valid CSS!