Zealot/Enemy (z-enemy) NVIDIA GPU miner (ver2.6.2 - kawpow RavenCoin).

[latinpmeow]

running amazing testing for 3 days! thanks a lot

[Ledaso]

is there a command to choose which GPU mine?

[NorbertColon]

is there a command to choose which GPU mine?

z-enemy.exe -a x16r -o stratum+tcp://x16r.mine.blazepool.com:3636 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p c=BTC -d 0,2

This runs z-enemy.exe on the x16r algo, hashing to blazepool, crediting my BTC wallet, payment set to BTC and the "-d 0,2" part tells z-enemy to use GPU 0 and GPU 2

[magicsys.nw]

All who got problem with hang during dev fee ming - solution:
You need to open ports for dev fee mining: 3336, 3366, 3666, 6666, 3636 and 5678

[Ledaso]

is there a command to choose which GPU mine?

z-enemy.exe -a x16r -o stratum+tcp://x16r.mine.blazepool.com:3636 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p c=BTC -d 0,2

This runs z-enemy.exe on the x16r algo, hashing to blazepool, crediting my BTC wallet, payment set to BTC and the "-d 0,2" part tells z-enemy to use GPU 0 and GPU 2

Thanks but idk why doesn't work

[tbearhere]

All who got problem with hang during dev fee ming - solution:
You need to open ports for dev fee mining: 3336, 3366, 3666, 6666, 3636 and 5678

Ok...that what it was...needed these ports.  Thx

[ULF]

is there a command to choose which GPU mine?

z-enemy.exe -a x16r -o stratum+tcp://x16r.mine.blazepool.com:3636 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p c=BTC -d 0,2

This runs z-enemy.exe on the x16r algo, hashing to blazepool, crediting my BTC wallet, payment set to BTC and the "-d 0,2" part tells z-enemy to use GPU 0 and GPU 2

What would be for Bitcore BTX on bitcorepool?
This is mistaked apparently cos does not work...
z-enemy.exe -a bitcore -o stratum+tcp://bitcorepool.cc:8001 -u (wallet) -i

[ULF]

How much Nvidia memory required to run this?
I still cannot get working.
I am try setup on 750ti OC 2GB ...it work fine for setup CCMiner and SPMod2
Should it be enough for Enemy Miner?
Select Bat, I only see flash on/off..can't read it
I looked BTX sample first page, cannot find what I am missing...

[ceozero]

where have 1.0.9?

[mensa1984]

where have 1.0.9?

https://discord.gg/Ga8kUTr

[NorbertColon]

is there a command to choose which GPU mine?

z-enemy.exe -a x16r -o stratum+tcp://x16r.mine.blazepool.com:3636 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p c=BTC -d 0,2

This runs z-enemy.exe on the x16r algo, hashing to blazepool, crediting my BTC wallet, payment set to BTC and the "-d 0,2" part tells z-enemy to use GPU 0 and GPU 2

What would be for Bitcore BTX on bitcorepool?
This is mistaked apparently cos does not work...
z-enemy.exe -a bitcore -o stratum+tcp://bitcorepool.cc:8001 -u (wallet) -i

Try:

z-enemy -a bitcore -o stratum+tcp://bitcorepool.cc:1111 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p x

you can always try different intensity settings after you've got it working.

[eruman34]

Hi Enemy,

Could you please add 19 gpu support to your miner thanks

[ULF]

is there a command to choose which GPU mine?

z-enemy.exe -a x16r -o stratum+tcp://x16r.mine.blazepool.com:3636 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p c=BTC -d 0,2

This runs z-enemy.exe on the x16r algo, hashing to blazepool, crediting my BTC wallet, payment set to BTC and the "-d 0,2" part tells z-enemy to use GPU 0 and GPU 2

What would be for Bitcore BTX on bitcorepool?
This is mistaked apparently cos does not work...
z-enemy.exe -a bitcore -o stratum+tcp://bitcorepool.cc:8001 -u (wallet) -i

Try:

z-enemy -a bitcore -o stratum+tcp://bitcorepool.cc:1111 -u 11nM156xreFE4DSZfpw2u7dKcyHqF2rZJ -p x

you can always try different intensity settings after you've got it working.

I had tried that exact before, except 8001...
but I changed to 1111, as your example...tried and still did not work
I remembered from 
prior experience other miner, I had shift one space to right worked.
tried that now still did not work...tried two space, I think got it,
as Kaspersky kicked in, removed Bat as virus...
Now to get around this, do I make exclusion or as trusted?
Those are two option I see Kaspersky that might apply

[Novicracker]

Hey guys I'm using a GTX 760 2g card. with the latest Nvidia drivers installed. And the miners says this:

[INFO   ] 18/05/08 16:14:44 zealot/enemy-1.08 miner
[INFO   ] 18/05/08 16:14:44 NVIDIA CUDA 9.1
[INFO   ] 18/05/08 16:14:44 Dev fee is 1.0%
[NOTICE ] 18/05/08 16:14:44 Starting on stratum+tcp://rvn-eu.coinblockers.com:4449
[INFO   ] 18/05/08 16:14:44 GPU monitoring enabled (NVAPI).
[ERROR  ] 18/05/08 16:14:44 GPU#0: Unsupported compute capability device. Ignoring
[INFO   ] 18/05/08 16:14:44 Mining 'x16r' with 0 thread.
[X16    ] 18/05/08 16:14:44 Hashorder algorithm legend: Slow Medium Fast
[WARNING] 18/05/08 16:14:45 New difficulty: 1.125 (0.00439)
[NOTICE ] 18/05/08 16:14:45 Block 203461, difficulty 21649.000
[NOTICE ] 18/05/08 16:14:56 Block 203462, difficulty 21649.000

Why is my Card not supported?

[cryptodunno]

Hey guys I'm using a GTX 760 2g card. with the latest Nvidia drivers installed. And the miners says this:

[INFO   ] 18/05/08 16:14:44 zealot/enemy-1.08 miner
[INFO   ] 18/05/08 16:14:44 NVIDIA CUDA 9.1
[INFO   ] 18/05/08 16:14:44 Dev fee is 1.0%
[NOTICE ] 18/05/08 16:14:44 Starting on stratum+tcp://rvn-eu.coinblockers.com:4449
[INFO   ] 18/05/08 16:14:44 GPU monitoring enabled (NVAPI).
[ERROR  ] 18/05/08 16:14:44 GPU#0: Unsupported compute capability device. Ignoring
[INFO   ] 18/05/08 16:14:44 Mining 'x16r' with 0 thread.
[X16    ] 18/05/08 16:14:44 Hashorder algorithm legend: Slow Medium Fast
[WARNING] 18/05/08 16:14:45 New difficulty: 1.125 (0.00439)
[NOTICE ] 18/05/08 16:14:45 Block 203461, difficulty 21649.000
[NOTICE ] 18/05/08 16:14:56 Block 203462, difficulty 21649.000

Why is my Card not supported?

probably gtx760 doesnt support cuda 9.1 as its quite old GPU generation, did you check it?

[brunocrypto]

Same here, Stratum connection interrupted, on two of my mining rig.

When restart, all is correct. but when stratum connection interrupt appear, then it can be block during HOURS without mining.

Please, what's the problem with this issue ?

Best regards

[@enemy]

First page updated.

Z-ENEMY VER 1.09a ( PUBLIC )

For Windows (Cuda 9.1)
zealot/enemy-1.09a (z-enemy)  From: Dk & Enemy

- Kernels speed improvements 1.08 vs 1.09a, for all 9x0 and 10x0 GTX:
 x16r +5-8%, x16s +5-10%, bitcore +5-8%, xevan +5-20% ( vs basic public), phi + 2-3%, x17 (basic), vit (new algo).

- Support new algos : Xevan (-a xevan) and Vitality (-a vit), recommended intensity for Xevan 19-20, for Vitality 19-21

- "Search mode" is enabled on 1.09a! This means that if you use a low diff you may see extra shares come through on your miner. You may see something like "2 shares" or "3 shares", up to 10+. This is a BONUS!.If you can find more than one share on your scan range you’ll find them all.If you have a bigger farm and use a higher diff you may also see the double or triple shares ,but it will be more rare. I still advise larger farms to continue to use higher diff.

- Revised dev-fee mechanism. Now the miner does not break off connection with a pool and does not drop work of video cards. Everything works without switch-offs.

- Now supporting failover pool! It is now possible to add additional pools incase your main pool loses stratum connection. Here is an example for your .bat file:
z-enemy -a x16r -o stratum+tcp://ravenminer.com:6666 -u RFQXKVKpHMwyJ86YqQUJSZK1S8m8oRbC5h -p d=16 -o stratum+tcp://krawww-miner.eu:3636 -u RFQXKVKpHMwyJ86YqQUJSZK1S8m8oRbC5h -p d=3

- Duplicate output into log file (-l, --log=logfile.txt )

- Better error reporting. Now you see device number with its name if you encounter any cuda errors.

- Pool latency. When submitting shares now you see pool's response time in milliseconds.

[rednoW]

- Better error reporting. Now you see device number with its name if you encounter any cuda errors.

thanks for all and for this especially !

[jugger1028]

Miner just seems to stop mining at certain points, nothing is happening, no crash, just stops mining like it's in pause mode. Checking MSI Afterburner, all clocks are dropped down like it's not mining anything and miner screen is just sitting on idle. Is this a known issue? I have 8x 1080 ti rig using this new 1.09a version. It's been paused like this for 10 minutes now, I will be restarting it in a minute.

Update: I was about to restart it but I just decided to hit backspace to see if something happened and soon as I did it kick started again? Then I got this:

[ERROR  ] 18/05/09 22:52:56 submit_upstream_work stratum_send_line failed
[ERROR  ] 18/05/09 22:52:56 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:52:56 Stratum authentication failed
[ERROR  ] 18/05/09 22:52:56 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:53:26 submit_upstream_work stratum_send_line failed
[ERROR  ] 18/05/09 22:53:26 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:53:27 Stratum authentication failed
[ERROR  ] 18/05/09 22:53:27 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:53:56 submit_upstream_work stratum_send_line failed
[ERROR  ] 18/05/09 22:53:56 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:53:57 Stratum authentication failed
[ERROR  ] 18/05/09 22:53:57 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:54:26 submit_upstream_work stratum_send_line failed
[ERROR  ] 18/05/09 22:54:26 ...retry after 30 seconds
[ERROR  ] 18/05/09 22:54:28 Stratum authentication failed
[ERROR  ] 18/05/09 22:54:28 ...retry after 30 seconds

And then after a few more retries it kicked in and is working again.

Few more pauses have occurred, some for 2mins, some for shorter, but I don't know if it's because Suprnova is overloaded with 11k miners or what the deal is. Switching back to 1.08 overnight and switching to 1.09 in the morning when I can monitor it again.

[@enemy]

Problem on the pool side