Thank-you Bitminerpro for another block!  and many more to come ! thx. keep it rollin' & let's keep kano bz with lotsa payouts  |
|
|
|
Shipping Update:
Orders in from the 14th, 15th have shipped.
Order from the 17th has not shipped yet.
ordered 22nd jan - unshipped |
|
|
|
|
gulp yum yum, more more pls to cover the bright red
|
|
|
|
|
can you guys post b9 order date & delivery dates ?
TIA. want to know where the deliveries stand.
|
|
|
|
pm'ed. not sure if you have the same 1.5 ths version. thx again for helping the community |
|
|
|
|
let me dig it & upload, will pm you when ready.
thx again.
|
|
|
|
Okay, one problem at a time - so API is a #CHECK#  A clock of 800 is afaik the stock setting for the 1.5 version, so that fits. How much less hashing do you see in comparison to stock firmware? yeps 800 is stock. it's about 200 ghs lower or more sometimes. the hashrate builds up really slow at pool side but miner side is already mining at full speed. ie : miner side says 1.5ths, pool side says 1.0 - 1.3 or even lower, sometimes after a long while abt 1 hr or so then it might get up to speed. must be something somewhere. i also tried 850/850 , 900/850 & other numbers, but 800 & 850 works well & responsive to hashrates, i tweaked around with the voltages not much difference. all of it were tested over a period of minimum 1 hour & in small increments. |
|
|
|
api works a little experience yes. at default it did not work well. lower hashrates on miner side & also on pool side. after small adjustments miner side improved but pool side showed lower hashrates. thats after at least 1 to 2 hrs of running. if use stock fw, both miner & pool is much closer on the hashrates. found that 800/800 works best so far. |
|
|
|
|
done that, tried n it works, but miner kinda acts weird using yr fw. maybe i couldn't find the correct volt & freq.
1.5 versions are very different from 1 or 2 thx versions.
must be the chip count. i'll mess with it more when i have time.
|
|
|
|
yslyung: First attempt indicates that just putting the whole s5 into oil does not work. Motherboard seems to demand air-based RPM, which is not possible in oil, for the large stock fan.
i said to extend the wires from controller to fan & use the fans to cool radiator ... then u get "air-based rpm" & so called trick the controller. just submerge the blades i did not say to submerge the whole miner like the russian video. now i'm confused ? |
|
|
|
My Antminer S5 seems to drop other board with these DDOSes and needs a reboot to get that board back online. Is it normal for Antminer S5 (sorry if this is a wrong place to ask)?
no its not normal.. post in the s5 thread your power supply and firmware version.. happened to 1 of my s7 too after hard reset it was ok. fw issue for sure. |
|
|
|
|
mod the wire of the fan then use the fan to cool the radiator. 2 birds with 1 stone.
agree with the vertical setup. i'm also considering to make a small project using oil immersion just for the fun of it but a little more proper than the 1 in the video.
ideas n suggestions are most welcomed.
|
|
|
|
|
received my b8 replacement boards, took roughly abt 2 weeks, they're mining fine now for abt 8 hrs or so.
boards are ver 1.1
|
|
|
|
That's how it works and that keeps it simple. If you want the API to listen on extra networks, just add it to /var/config/extraopts. It will be kept. Please, please be aware that this is a possible security issue.
I have no plans to extend the webgui, it really just adds complexity to the crappy parts of the original firmware interface.
A table with voltage and clock settings sounds like a good idea for everyone ☺
thx, will try it soon. so just add below the volt & freq lines ? api-allow W:127.0.0.1,W:192.168.1.0/24 |
|
|
|
can u make it api-allow W:127.0.0.1/W:192.168.1.0/24 port 4028 by default ? i tried to write that in nano in run.sh file but after a reboot it overwrites it. i think for newbies who are not familiar, take it slow n ask questions before doing anything else. as for my 1.5ths i had to change the freq & voltages. it'll be nice if we could compile list of freq & voltages ? i flashed twice, latest version 1.2 when booted up i tried to change the ip on gui it did not respond well, hard reboot then ok. after that when i was changing pools & username, same issue, have to hard reboot. a it was using the webgui. not sure about via ssh. it'll be nice if u can make a menu in the webgui for the api allow & more options ? this screenshot is from coin craft desks.  thx again for the effort op. |
|
|
|
|
green getting brighter ! yum
|
|
|
|
|
first time using escrow, sebastian guided me thru the process.
thx so much. trusted escrow. will use again !
|
|
|
|
|
thx for the giveaway contest. miners are warmed up, GL to everyone.
|
|
|
|
|
amazing, 6 fans ? 3 or 4 psu to power 1 miner ?
hmmmmmmmmmmmmm
GL to those who do not have 220/240V
mobile bbq machine, hot air blower
|
|
|
|
|
Show Posts
