PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[PhoenixMiner]

PhoenixMiner 5.6c is officially released. You can find the download link and the checksums in the first post of this thread.

It is the same release as the one that was posted yesterday as release candidate, so if you are already running it, there is no need to upgrade.

[sunnyguy123]

5.6c works fine so far on Windows 10 (18 hours and counting) on GTX 1070. The only issue I have is the temperature is not shown.

[Lkokra]

Hello,

I have AMD RX580 8 GB with the driver 21.4.1 also phoenixminer 5.6b which would be perfect for this driver BUT there is one problem when I Tune my GPU and turn of FANS on 50% every time it crush in like 10 or 15 minutes later I don't know what's going on also this problem was early drivers and the AMD error Say "We detected a driver timeout has occurred on your system. A bug report has been generated. This report could help AMD find a solution... " Compute mode is turned ON... The miner working on Windows 10...

any ideas? please help me <3

Never forget this: In mining not always latest drivers means best. There must be time devs can upgrade miners after that you can use.
For example myself using 5.4c with driver 20.11.1 i will not change until long period,
Download 20.11.1 driver and try again. and also if you share bat file you will get more help.

I tried it and there is a bug report again I am sharing bat file 
-amd -gt 63   -daglim 3950 -mt 2 -rxboost 20 -cclock 1175 -cvddc 850
 
I want to max my hashrate because i have 28.5 and 100W i know that it is not good Can anyone help me you can add me on facebook or somewhere else where you can chat me to configure this problem please ^_^ i can't mine it :/

[hitpro]

hello. i'm got a error on all Phoenix Version on SimpleMining os :
i'm using RX 580 Saphire

[ 170.611797] amdgpu 0000:04:00.0: amdgpu: GPU fault detected: 146 0x0ff8c40c for process PhoenixMiner pid 6501 thread PhoenixMiner pid 6501
[ 170.613681] amdgpu 0000:04:00.0: amdgpu: VM_CONTEXT1_PROTECTION_FAULT_ADDR 0x00105DFF
[ 170.615528] amdgpu 0000:04:00.0: amdgpu: VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C400C
[ 170.617377] amdgpu 0000:04:00.0: amdgpu: VM fault (0x0c, vmid 7, pasid 32778) at page 1072639, read from 'TC3' (0x54433300) (196)
[ 170.626796] amdgpu 0000:07:00.0: amdgpu: GPU fault detected: 146 0x0ff8c40c for process PhoenixMiner pid 6501 thread PhoenixMiner pid 6501
[ 170.628587] amdgpu 0000:07:00.0: amdgpu: VM_CONTEXT1_PROTECTION_FAULT_ADDR 0x00105DFF
[ 170.630328] amdgpu 0000:07:00.0: amdgpu: VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C400C
[ 170.632069] amdgpu 0000:07:00.0: amdgpu: VM fault (0x0c, vmid 7, pasid 32781) at page 1072639, read from 'TC3' (0x54433300) (196)
[ 170.638753] amdgpu 0000:07:00.0: amdgpu: GPU fault detected: 146 0x0ff8c40c for process PhoenixMiner pid 6501 thread PhoenixMiner pid 6501
[ 170.640278] amdgpu 0000:07:00.0: amdgpu: VM_CONTEXT1_PROTECTION_FAULT_ADDR 0x00105DFF
[ 170.641760] amdgpu 0000:07:00.0: amdgpu: VM_CONTEXT1_PROTECTION_FAULT_STATUS 0x0E0C400C
[ 170.643246] amdgpu 0000:07:00.0: amdgpu: VM fault (0x0c, vmid 7, pasid 32781) at page 1072639, read from 'TC3' (0x54433300) (196)

[batsonxl]

Hello,

I have AMD RX580 8 GB with the driver 21.4.1 also phoenixminer 5.6b which would be perfect for this driver BUT there is one problem when I Tune my GPU and turn of FANS on 50% every time it crush in like 10 or 15 minutes later I don't know what's going on also this problem was early drivers and the AMD error Say "We detected a driver timeout has occurred on your system. A bug report has been generated. This report could help AMD find a solution... " Compute mode is turned ON... The miner working on Windows 10...

any ideas? please help me <3

Never forget this: In mining not always latest drivers means best. There must be time devs can upgrade miners after that you can use.
For example myself using 5.4c with driver 20.11.1 i will not change until long period,
Download 20.11.1 driver and try again. and also if you share bat file you will get more help.

I tried it and there is a bug report again I am sharing bat file 
-amd -gt 63   -daglim 3950 -mt 2 -rxboost 20 -cclock 1175 -cvddc 850
 
I want to max my hashrate because i have 28.5 and 100W i know that it is not good Can anyone help me you can add me on facebook or somewhere else where you can chat me to configure this problem please ^_^ i can't mine it :/

Did you installed right driver? What card is it? 470 480 570 580 what card? Windows?
Delete your command and start with this : -cclock 1150 -cvddc 920 -mclock 2050 -mvddc 920 -rxboost 1 -mt 1
if it is stable you can increase mclock then decrease voltage until it crashes.

[StonieMalony]

Hello

What's happening ? on PhoenixMiner 5.6c no longer show gpu temp in Linux ... works ok in windows

any quick workarounds ?

[alikait]

PhoenixMiner 5.6c is officially released. You can find the download link and the checksums in the first post of this thread.

It is the same release as the one that was posted yesterday as release candidate, so if you are already running it, there is no need to upgrade.

Now it doesn't show gpu temps for Nvidia cards lol, previously AMD cards were not showing but they're showing fine, Nvidia cards have the same issue now. Please address, thanks!

[Lkokra]

Hello,

I have AMD RX580 8 GB with the driver 21.4.1 also phoenixminer 5.6b which would be perfect for this driver BUT there is one problem when I Tune my GPU and turn of FANS on 50% every time it crush in like 10 or 15 minutes later I don't know what's going on also this problem was early drivers and the AMD error Say "We detected a driver timeout has occurred on your system. A bug report has been generated. This report could help AMD find a solution... " Compute mode is turned ON... The miner working on Windows 10...

any ideas? please help me <3

Never forget this: In mining not always latest drivers means best. There must be time devs can upgrade miners after that you can use.
For example myself using 5.4c with driver 20.11.1 i will not change until long period,
Download 20.11.1 driver and try again. and also if you share bat file you will get more help.

I tried it and there is a bug report again I am sharing bat file 
-amd -gt 63   -daglim 3950 -mt 2 -rxboost 20 -cclock 1175 -cvddc 850
 
I want to max my hashrate because i have 28.5 and 100W i know that it is not good Can anyone help me you can add me on facebook or somewhere else where you can chat me to configure this problem please ^_^ i can't mine it :/

Did you installed right driver? What card is it? 470 480 570 580 what card? Windows?
Delete your command and start with this : -cclock 1150 -cvddc 920 -mclock 2050 -mvddc 920 -rxboost 1 -mt 1
if it is stable you can increase mclock then decrease voltage until it crashes.

yes i installed right driver 20.11.1 and 5.4c phoenixminer... but i have about 28 MH/s for 100W why ?
i don't know really i have xfx rx580 8 gb card i know that there must be at least 30-31 mh/s with 70W- 80W for per card 
also yes Windows ...

[snappleapple100]

new update working really good , longest up time so far 62+ hours zero incorrect shares on windows 10 , running 2 3070s 61.3 hash both running around 54-56 and i have 1 3080 getting 100hash at 60c

[dazmann]

Hello,

I have AMD RX580 8 GB with the driver 21.4.1 also phoenixminer 5.6b which would be perfect for this driver BUT there is one problem when I Tune my GPU and turn of FANS on 50% every time it crush in like 10 or 15 minutes later I don't know what's going on also this problem was early drivers and the AMD error Say "We detected a driver timeout has occurred on your system. A bug report has been generated. This report could help AMD find a solution... " Compute mode is turned ON... The miner working on Windows 10...

any ideas? please help me <3

Never forget this: In mining not always latest drivers means best. There must be time devs can upgrade miners after that you can use.
For example myself using 5.4c with driver 20.11.1 i will not change until long period,
Download 20.11.1 driver and try again. and also if you share bat file you will get more help.

I tried it and there is a bug report again I am sharing bat file 
-amd -gt 63   -daglim 3950 -mt 2 -rxboost 20 -cclock 1175 -cvddc 850
 
I want to max my hashrate because i have 28.5 and 100W i know that it is not good Can anyone help me you can add me on facebook or somewhere else where you can chat me to configure this problem please ^_^ i can't mine it :/

Did you installed right driver? What card is it? 470 480 570 580 what card? Windows?
Delete your command and start with this : -cclock 1150 -cvddc 920 -mclock 2050 -mvddc 920 -rxboost 1 -mt 1
if it is stable you can increase mclock then decrease voltage until it crashes.

yes i installed right driver 20.11.1 and 5.4c phoenixminer... but i have about 28 MH/s for 100W why ?
i don't know really i have xfx rx580 8 gb card i know that there must be at least 30-31 mh/s with 70W- 80W for per card 
also yes Windows ...

30-31mh/s even 32 are for RX580 with custom bios.
rxboost increases power consumption.
If you're using the GPU to output video to a monitor you can get lower rashrate.
Se if the memory clock has a lower state than 2000MHz on the radeon settings, if it does, set the 2000MHz as the lowest state and try generating the DAG again. Sometimes generating dag at a lower clock gets you a lower hashrate.
remove the -gt value, and the -rxboost value, try those commands without a value and see at which value they settle.

[User_Shmuser]

Does anyone run this on linux with newer kernel than 5.10?

It works perfectly fine on 5.10 but as soon as I try booting with 5.11, it starts working just fine but then in about few minutes it starts slowing down the whole OS to basically 0.5 FPS until I kill the process.

I tried running it with minimum additional parameters and it's still the same.

[Vann]

No problems running 5.6c with Polaris RX580's in Linux 5.12 and AMD 21.10 drivers. It runs flawless and I also have full overclocking and power settings through the miner config or terminal with rocM. However with a Nvidia Pascal rig it doesn't show the temperature with Phoenix 5.6 and it has some issues with slowing down the primary GPU when mining and using the system. The problem is Nvidia Linux drivers are garbage.

[tumbev]

Hello. I have two rigs with windows 10. Every week or two I have issues with the miners. Today one of the miners stopped working,
the error in phoenixminer is "Unable to establish secure connection to ssl://***.ethermine.org:5555: certificate verify failed."
3 or 4 hours later the same thing happened with the second miner... If I remove the "ssl://" from the config file, the miner works but it not show up in the ethermine website. Usually after 3-5 days the problem dissapears...  What can be the problem? I am using wi-fi dongles if that matters

Make sure your timezone, date and time are correct in Windows.

Certificate issues can be caused by incorrect dates / times on the local machines.

The thing is that when I use my main internet connection there is ssl error but when I connect to my 4G internet from my phone there is no ssl error... When I delete the "ssl://" and use eu1.ethermine.org:4444, the miner works but with few valid shares... my gtx 1070 only show 8-12 valid shares

[PhoenixMiner]

The problem with the missing GPU temperatures on Nvidia GPUs is fixed and we released new version with the fix: PhoenixMiner 5.6d. You can find the download links and checksums in the first post of this thread.

If you are already running 5.6c and your rigs are not showing GPU temperatures, the easiest fix is to add the command-line option -hstats 2

Of course, you can also upgrade to PhoenixMiner 5.6d but the only difference between 5.6c and 5.6d is the fixed problem with GPU temperatures not shown with some Nvidia cards.

Sorry about this regression, we happen to run all of our test rigs with -hstats 2 and that's why we didn't detect the problem sooner.

[cryptojohn42]

Is there any way to get the AMD 6XXX (e.g. 6900) to switch to Manual tuning if it's not already without using Adrenaline UI?

If I have to force reboot (or crash) Adrenaline resets to the default automatic mode. In this mode I can't set clocks/voltages (neither with PM nor OverdriveNTool).

Is there a command line tool to switch to a manual preset somehow?

[UnclWish]

The new features in this release (since 5.6b) are:

• Lower percent of rejected/stale shares when mining on Nicehash

I didn't noticed any reduction of rejected shares on nicehash. Still about 1,2-1,5%.

And another one: I noticed that TR miner uses about 1-2W of power less than PM on Polarises 8Gb cards. And it's only reported by sensors.

[user02010]

Hello everyone,

Wondering if I can get any assistance with this

I've got an MSI Radeon RX 580 ARMOR MK2 8gb (Hynix memory) (500w PSU)

Yes it is in Compute mode (not graphics). I have a different RX580 that works fine with ethash (on a 450w psu)

Running with latest drivers OR older drivers, doesn't make a difference.

Symptom: Either repeatedly showing 0mhs or if I enable -clKernel 0, I get maybe 8 to 10mhs.
Overclocking vram or default, doesn't make too much of a difference (maybe like 1 or 2mhs)

Are there specific BIOS settings I should be looking at?


TIA

[WARMANGALAXY]

GitHub CLOSED miner!!!!

[Shlimann]

Checksums for my unpacked 5.6d files downloaded 11.05.2021 from GitHub follows:

PhoenixMiner.exe:
SHA256 e8e775add50c67e1c6f6ca20db318f745e22b085afcbdf5634015e6ef91e8853

EIO.dll:
SHA256 287e44f5067a4e770e8a0605f5720d3d1477ecc4aa4f3a26ce5d3a489ae79780

EIO.exe:
SHA256 402438684406d1e3b2d1d5629151259ad864ffc55c8e6ab176f4c47c543d4fee

IOMap64.sys
SHA256 ad20e44954960278ad965b05e8c67d9d314c200809b99b1b5a219a916ce06b21

check the sums of the exe, dll, EIO and IOMap64 files, they must match these.

you can verify Checksums here: md5file.com/calculator. Just upload there there one by one PhoenixMiner.exe, EIO.dll, EIO.exe: and IOMap64.sys.

You should have the same amounts as those I indicated above.
While the issue is being resolved with GitHub.

[Force098]

Did the Github repository get removed? It looks like the links go to a 404 page.