PhoenixMiner 6.2c: fastest Ethereum/Ethash miner with lowest devfee (Win/Linux)

[doctorman]

RTX 3000 series   fellows..


What straps do you guys use in windows?

sometimes my  13GPU RTX 3070 rig crashes and does not load well after the restart

the only way to fix it is  system disk clean up
turn off the GPUs and then turn everything back on


if I don't do that the DAG takes very long to create and I get errors halfway through DAG creation and the system crashes again

Is there a certain memory clean-up, DAG leftover files somewhere  , or some mess that I can set to have cleaned during a start-up to help with this?


Log file  is here   https://pastebin.com/ffxrrWED


Seams like on the startup it skips creating the dag or it is a messed up dag creation...

[batsonxl]

Having trouble getting my rx 570 8gb Pulse with Samsung memory stable.  Using Windows 10

Use 1 click BIOS editor, flash,  then Phoenixminer to change clocks/volts

I have tried 1130-1150/850 and 2050-2100/860 and none of the times stay stable with a Blue screen hanging in the driver. All seem to run 5-60 minutes.

Any suggestions?  Never had a 570 outside of these paramaters unstable  unless going higher but 1130/2050 are my beginning settings.

Thanks

start with 950-960mv then slowly decrease to see which card crashing

[Bagge6]

Is it possible to go further than +1000MHz mem oc with MSI GeForce 1060 6gb Gaming X? Seems that the "unofficial overclocking limit" by afterburner is only unlocked with AMD cards... I am using +1000MHz mem clock with this card and it doesnt show any errors/crashes, but how can I go further than 1000? Or is it bad for the card

[lexfazio]

Finally I couldn't fix this problem.
I've tried with Windows and HiveOS, PhoenixMiner 5.5c, TRexMiner and NBminer, upgrading drivers or downgrading.

But nothing worked  .

I think this card is troubled for mining, can't infer why.
So, I'm giving it back to the seller or selling it just for gaming.

[91to]

answer please! I have 1080 ti and 1070. The drivers are the newest. PhoenixMiner 5.5c. mining ether
on phoenix I have:
1080 ti - 15 mh / s
1070 - 17 mh / s

on gminer I have:
1080 ti - 36 mh / s
1070 - 28 mh / s

  The overclocking is the same, the temperatures are the same. Why is phoenix showing so little?

[Vann]

answer please! I have 1080 ti and 1070. The drivers are the newest. PhoenixMiner 5.5c. mining ether
on phoenix I have:
1080 ti - 15 mh / s
1070 - 17 mh / s

on gminer I have:
1080 ti - 36 mh / s
1070 - 28 mh / s

  The overclocking is the same, the temperatures are the same. Why is phoenix showing so little?

ETH Only I get ~28 MH/s 1070, ~36 MH/s 1080 and ~45 MH/s 1080 Ti.

PhonenixMiner v5.5c Windows 10 20H2 Nvidia GeForce 461.72 Driver

Code:

2021.02.28:12:35:16.317: main *** 5:27 *** 2/28 12:35 **************************************
2021.02.28:12:35:16.317: main Eth: Mining ETH on ssl://us1.ethermine.org:5555 for 5:27
2021.02.28:12:35:16.317: main Eth: Accepted shares 497 (0 stales), rejected shares 0 (0 stales)
2021.02.28:12:35:16.317: main Eth: Incorrect shares 0 (0.00%), est. stales percentage 0.00%
2021.02.28:12:35:16.317: main Eth: Maximum difficulty of found share: 5824.8 GH (!)
2021.02.28:12:35:16.317: main Eth: Average speed (5 min): 108.993 MH/s
2021.02.28:12:35:16.317: main Eth: Effective speed: 101.25 MH/s; at pool: 101.25 MH/s
2021.02.28:12:35:16.317: main 
2021.02.28:12:35:16.949: main Eth speed: 109.115 MH/s, shares: 497/0/0, time: 5:27
2021.02.28:12:35:16.949: main GPUs: 1: 28.121 MH/s (134) 2: 44.985 MH/s (194) 3: 36.009 MH/s (169)

MSI Afterburner Overclock Settings:

Code:

GPU 1: Zotac AMP! Extreme 8G GTX 1070 - 70% Power Limit +100 Core +300 Memory 92 Temp Limit Fan Speed 55%
GPU 2: MSI Duke 11G OC GTX 1080 Ti - 88% Power Limit +135 Core +500 Memory 90 Temp Limit Fan Speed 83%
GPU 3: MSI Gaming X 8G GTX 1080 - 65% Power Limit +100 Core +700 Memory 92 Temp Limit Fan Speed 85%

PhoenixMiner config.txt:

Code:

-coin eth
-ptimeout 15
-ftimeout 300
-tt -55,-83,-85
-tstop 78
-r 0
-gser 1
-eres 5
-logdir logs\
-mode 1
-nvidia
-mi 14,14,14
-gpus 123
-nvKernel 3
-nvdo 1
-nvNew 1
-gbase 1
-nvmem 1,2,2
-vmr 12,12,100
-straps 0,2,2

[sushmee]

Hey there, getting these errors with some NVIDIA rigs, some insight could be good. Thanks!

Code:

2021.03.01:09:45:47.397: GPU5 CUDA error in CudaProgram.cu:465 : the launch timed out and was terminated (702)
2021.03.01:09:45:47.397: GPU5 GPU5 search error: the launch timed out and was terminated
2021.03.01:09:45:47.408: GPU6 CUDA error in CudaProgram.cu:465 : the launch timed out and was terminated (702)
2021.03.01:09:45:47.408: GPU6 GPU6 search error: the launch timed out and was terminated
2021.03.01:09:45:47.425: GPU3 CUDA error in CudaProgram.cu:465 : the launch timed out and was terminated (702)
2021.03.01:09:45:47.425: GPU3 GPU3 search error: the launch timed out and was terminated
2021.03.01:09:45:47.427: GPU4 CUDA error in CudaProgram.cu:465 : the launch timed out and was terminated (702)
2021.03.01:09:45:47.427: GPU4 GPU4 search error: the launch timed out and was terminated
2021.03.01:09:45:47.442: wdog Fatal error detected. Restarting.
2021.03.01:09:45:47.455: GPU1 CUDA error in CudaProgram.cu:465 : the launch timed out and was terminated (702)
2021.03.01:09:45:47.455: GPU1 GPU1 search error: the launch timed out and was terminated
2021.03.01:09:45:47.455: GPU2 CUDA error in CudaProgram.cu:465 : the launch timed out and was terminated (702)
2021.03.01:09:45:47.455: GPU2 GPU2 search error: the launch timed out and was terminated

Clocks:

Core: +90
Memory: +580
PL: 140

Cards: GeForce GTX 1070 8119 MB · Gigabyte Micron GDDR5 · 86.04.50.00.7A

Edit: Also getting some rejected shares

[Permonik]

Hi guys,
What are your h/s for RX6800 ?

Thanks

[Littlegrand]

Having trouble getting my rx 570 8gb Pulse with Samsung memory stable.  Using Windows 10

Use 1 click BIOS editor, flash,  then Phoenixminer to change clocks/volts

I have tried 1130-1150/850 and 2050-2100/860 and none of the times stay stable with a Blue screen hanging in the driver. All seem to run 5-60 minutes.

Any suggestions?  Never had a 570 outside of these paramaters unstable  unless going higher but 1130/2050 are my beginning settings.

Thanks

start with 950-960mv then slowly decrease to see which card crashing

Funny it wasnt this card thats why nothing worked, when I installed this card, it was another card I had to cut back on the memory that had been mining fine. Strange

[Littlegrand]

I have a 5700 xt on the way....

With 5700 xt, Do you still use the 1 click bios editor and then change core/mem in phoenix?  And can someone post some starting numbers for MSI RX 5700 XT 8 gig

Thanks

[Kiawpqe]

Hi guys,
What are your h/s for RX6800 ?

Thanks

new rig

*** 0:06 *** 3/1 21:55 **************************************
Eth: Mining ETH on ssl://eu1.ethermine.org:5555 for 0:06
Available GPUs for mining:
GPU1: AMD Radeon RX 5700 XT (pcie 3), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU2: AMD Radeon RX 5700 XT (pcie 12), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU3: AMD Radeon RX 6800 (pcie 16), OpenCL 2.0, 16 GB VRAM, 30 CUs
GPU4: Radeon RX 580 Series (pcie 18), OpenCL 2.0, 8 GB VRAM, 36 CUs
GPU5: AMD Radeon RX 5700 XT (pcie 21), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU6: AMD Radeon RX 5700 XT (pcie 24), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU7: AMD Radeon RX 5700 XT (pcie 27), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU1: 52C 0% 92W, GPU2: 45C 58% 132W, GPU3: 57C 25% 177W, GPU4: 46C 68% 84W, GPU5: 44C 55% 99W, GPU6: 45C 56% 89W, GPU7: 45C 58% 90W
GPU1: cclock 1162 MHz, cvddc 756 mV, mclock 1812 MHz, mvddc 850 mV, Tj 57C, Tmem 80C
GPU2: cclock 1212 MHz, cvddc 756 mV, mclock 1846 MHz, mvddc 850 mV, Tj 55C, Tmem 82C
GPU3: cclock 1242 MHz, cvddc 793 mV, mclock 2088 MHz, Tj 61C
GPU4: cclock 1150 MHz, cvddc 862 mV, mclock 2100 MHz
GPU5: cclock 1225 MHz, cvddc 756 mV, mclock 1880 MHz, mvddc 850 mV, Tj 53C, Tmem 72C
GPU6: cclock 1227 MHz, cvddc 756 mV, mclock 1802 MHz, mvddc 850 mV, Tj 52C, Tmem 64C
GPU7: cclock 1223 MHz, cvddc 756 mV, mclock 1880 MHz, mvddc 850 mV, Tj 50C, Tmem 70C
GPUs power: 762.8 W; cost: 2.47 USD/day
Current -gt 21,38,203,66,36,25,37
Eth: Accepted shares 36 (0 stales), rejected shares 0 (0 stales)
Eth: Incorrect shares 0 (0.00%), est. stales percentage 0.00%
Eth: Maximum difficulty of found share: 995.0 GH (!)
Eth: Average speed (5 min): 361.339 MH/s
Eth: Effective speed: 351.22 MH/s; at pool: 351.22 MH/s
Eth: Estimated income: 30.62 USD/day

Eth: New job #512792a9 from ssl://eu1.ethermine.org:5555; diff: 4000MH
Eth speed: 361.331 MH/s, shares: 36/0/0, time: 0:06
GPUs: 1: 51.839 MH/s (3) 2: 53.500 MH/s ( 3: 62.940 MH/s (6) 4: 31.745 MH/s (3) 5: 54.474 MH/s ( 6: 52.408 MH/s (3) 7: 54.425 MH/s (5)


i config now and try

[waywoos]

I have a 5700 xt on the way....

With 5700 xt, Do you still use the 1 click bios editor and then change core/mem in phoenix?  And can someone post some starting numbers for MSI RX 5700 XT 8 gig

Thanks

no its more involved now days.
you have to manually do it. look on youtube on the red panda mining channel. the specialize in the 5700xt

[Denton_Miner]

Hello everyone,

I also wanted to try ETH-mining and ordered some new hardware. New mainboard, new CPU and also a new graphics card:

Operating system: Windows 10 Pro, 64-bit
DirectX version: 12.0
GPU processor: GeForce RTX 2070 SUPER
Driver version: 461.72
Driver type: DCH
Direct3D function level: 12_1
CUDA cores: 2560
Core clock: 1905 MHz
Memory data rate: 14.00 Gbps
Memory interface: 256-bit
Memory bandwidth: 448.06 GB/s
Total available graphics memory: 16347 MB
Dedicated video memory: 8192 MB GDDR6
System video memory: 0 MB
Free system memory: 8155 MB
Video-BIOS-Version: 90.04.86.00.47
IRQ: Not used
Bus: PCI Express x16 Gen3
Device ID: 10DE 1E84 87271043
Part number: G180 0012

However, when I start the Phoenixminer the following error message appears:

https://i.ibb.co/J3z18hH/Unbenannt.png

I have already set changes to all possible settings.   Firewall and Windows Defender is disabled.

Does anyone here have a tip for what I could try to get the Phoenixminer to start?

Thank you very much.  

[VRMdude]

Any chance of a -maxRigSpeed option as a flakey gpu occasionally gives a million gazzillion hash rate that wdog doesnt act on and the pool boots the entire rig for it until a manual miner restart. That particular GPU will work fine without reboot. Have been fine tuning that GPU for a few weeks it has no orderly sense its one with Gremlins, have to run it steady very delicate thing....

Thanks

[rboer]

HI,

i tried searching for an answer but did not found so sorry if it was already addressed.
I am running straps but i want to use Afterburn again to OC my Nvidia cards but afterburn is grey out or disabled any ideas?
Using 5.5c

thanks

[cirlama]

Hi all,
do you know why PhoenixMiner creates a file called "PhoenixMiner.Vexe" in the same directory (with windows process)?

[Kiawpqe]

NEW RIG
WORKING FINE


Eth speed: 378.901 MH/s, shares: 96/0/0, time: 0:17
GPUs: 1: 52.756 MH/s (15) 2: 58.111 MH/s (19) 3: 63.077 MH/s (10) 4: 32.360 MH/s (1) 5: 58.432 MH/s (18) 6: 55.747 MH/s (18) 7: 58.418 MH/s (15)

*** 0:17 *** 3/2 20:38 **************************************
Eth: Mining ETH on ssl://eu1.ethermine.org:5555 for 0:17
Available GPUs for mining:
GPU1: AMD Radeon RX 5700 XT (pcie 3), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU2: AMD Radeon RX 5700 XT (pcie 12), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU3: AMD Radeon RX 6800 (pcie 16), OpenCL 2.0, 16 GB VRAM, 30 CUs
GPU4: Radeon RX 580 Series (pcie 18), OpenCL 2.0, 8 GB VRAM, 36 CUs
GPU5: AMD Radeon RX 5700 XT (pcie 21), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU6: AMD Radeon RX 5700 XT (pcie 24), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU7: AMD Radeon RX 5700 XT (pcie 27), OpenCL 2.0, 8 GB VRAM, 40 CUs
GPU1: 44C 60% 94W, GPU2: 44C 77% 138W, GPU3: 59C 24% 183W, GPU4: 49C 51% 85W, GPU5: 44C 66% 101W, GPU6: 45C 62% 91W, GPU7: 45C 65% 93W
GPU1: cclock 1257 MHz, cvddc 756 mV, mclock 1814 MHz, mvddc 850 mV, Tj 49C, Tmem 74C
GPU2: cclock 1330 MHz, cvddc 756 mV, mclock 1880 MHz, mvddc 850 mV, Tj 54C, Tmem 84C
GPU3: cclock 1244 MHz, cvddc 793 mV, mclock 2092 MHz, Tj 63C
GPU4: cclock 1190 MHz, cvddc 862 mV, mclock 2110 MHz
GPU5: cclock 1344 MHz, cvddc 756 mV, mclock 1890 MHz, mvddc 850 mV, Tj 52C, Tmem 72C
GPU6: cclock 1280 MHz, cvddc 762 mV, mclock 1802 MHz, mvddc 850 mV, Tj 52C, Tmem 64C
GPU7: cclock 1344 MHz, cvddc 756 mV, mclock 1890 MHz, mvddc 850 mV, Tj 51C, Tmem 74C
GPUs power: 784.7 W; cost: 2.54 USD/day
Current -gt 36,37,15,45,29,43,42
Eth: Accepted shares 96 (0 stales), rejected shares 0 (0 stales)
Eth: Incorrect shares 0 (0.00%), est. stales percentage 0.00%
Eth: Maximum difficulty of found share: 367.3 GH (!)
Eth: Average speed (5 min): 378.895 MH/s
Eth: Effective speed: 372.45 MH/s; at pool: 372.45 MH/s
Eth: Estimated income: 34.14 USD/day

[stoniestfool]

You may want to know the eth core devs are pushing through a reward reduction. Those profits will not last.
Congratulations on the rig and welcome to the community.

https://bitcointalk.org/index.php?topic=5321264.0

[radic]

I get "Unable to set memory clock delta to -1000 MHz -error -137"

I am running Evga 3090 with latest nvidia driver 461.72. I am trying to quit using MSI afterburner and insted I am trying to use the phoenixminer overclock settings int the .bat file for my gpu. As a starter I just simply tried to set the memory clock to some not that high value like "-mclock 400".

The DAG file loads, everything runs just fine but my MH/s speed is the basic one and from time to time I get this error "Unable to set memory clock delta to -1000 Mhz - error -137"

*using phoenixminer 5.5c

[rockert]

Does anyone know why my rtx 3080 is limited by the miner to a power always of 200w and although the memory goes up nothing happens

https://i.ibb.co/x8qYVBJ/Sin-t-tulo.png