[GUIDE] BitFury Miner Support/Tuning

[klondike_bar]

you can also ... regulate with clockspeed ... that's what i did ...

I had one board shutting down because graphite getting to low resistance on high temp ...


so I put all chips to clockspeed 53 ... now it's again stable ... and I can slowly approach again ...


It would be interesting to see which chip is where located ....

chips with big distance to the reg & resistor ... will probably have lesser influence ^^

Code:

+-+-+-+-+
|3|4|B|C|
+-+-+-+-+
|2|5|A|D|
+-+-+-+-+
|1|6|9|E|
+-+-+-+-+
|0|7|8|F|
+-+-+-+-+
  |||||
  +++++

im not sure. i clocked chips 3-6 from 54 to 55 and it resulted in errors. right now, all chips are tuned to 54 without an issue and my hashrate is around 39.5GH. I half expect this to rise a little bit, since the resistance seems to fluctuate with the ambient temperature. In the evening when my apartment is the warmest is when ive always seen it produce the highest hashrates but also push the limit where errors take over and start shutting down chips and shunting my hashrate.

42GH seems to be the upper bound before this occurs, at least with my prior heatsink configuration. Im happy to run a few days as it is now to follow the results and see how stability is. (in my mind, anything over 35 is sweet, so to be pushing the lower edge of 40GH is perfect)

[1714191478]

1714191478

[1714191478]

1714191478

[1714191478]

1714191478

[1714191478]

1714191478

[juhakall]

I received a new october card where the R02F resistor was 2.11k instead of 1.8k. Pencil modding it 2.05 boosted the valid hashrate from 32 GH/s to 34.5 GH/s, even though one chip dropped semi-dead after the modding.

[goxed]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

[Keefe]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

I have 4 cards, without problems most of the time. More are arriving later today.

[goxed]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

I have 4 cards, without problems most of the time. More are arriving later today.

wow, I have two stubborn version 1 M boards, that just wont hash properly with more than 3 H cards.

 What is your hashrate with 4 cards? Are you using the chainminer that came with the board? Any special settings? Thanks in advance.

[Keefe]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

I have 4 cards, without problems most of the time. More are arriving later today.

wow, I have two stubborn version 1 M boards, that just wont hash properly with more than 3 H cards.

 What is your hashrate with 4 cards? Are you using the chainminer that came with the board? Any special settings? Thanks in advance.

138.5 GH total, but 3 chips are dead (2 bypassed and 1 at the end of the chain). I overvolted them to an average of 0.78v. I'm using the stock software. Autotune is off, and some chips are set to 54 and some to 55, based on manual testing.

[goxed]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

I have 4 cards, without problems most of the time. More are arriving later today.

wow, I have two stubborn version 1 M boards, that just wont hash properly with more than 3 H cards.

 What is your hashrate with 4 cards? Are you using the chainminer that came with the board? Any special settings? Thanks in advance.

138.5 GH total, but 3 chips are dead (2 bypassed and 1 at the end of the chain). I overvolted them to an average of 0.78v. I'm using the stock software. Autotune is off, and some chips are set to 54 and some to 55, based on manual testing.

That's cool. I get 115GH/s with 3 H-boards. The moment I add the fourth it falls to 84GH/s. Using stock software, tried  both Autotune on and off. I guess I will have to dig deeper. Hashrate starts off good after power on and falls down within a minute or so.   Thanks for your help though

[Cablez]

I have 16 cards on a V1 M-board.  It runs reasonably well most of the time.  I would prefer to upgrade to a V2 so I can at least update chainminer and reduce errors but no love yet. 

[klondike_bar]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

I have 4 cards, without problems most of the time. More are arriving later today.

wow, I have two stubborn version 1 M boards, that just wont hash properly with more than 3 H cards.

 What is your hashrate with 4 cards? Are you using the chainminer that came with the board? Any special settings? Thanks in advance.

138.5 GH total, but 3 chips are dead (2 bypassed and 1 at the end of the chain). I overvolted them to an average of 0.78v. I'm using the stock software. Autotune is off, and some chips are set to 54 and some to 55, based on manual testing.

drop the tuning to 53/54, ands increase the voltage to 0.805V. youll get a little bit faster speeds from increasing the voltage/tuning ratio rather than vice-versa

[juhakall]

I've heard of three people in the last 24 hours who received their miners with an empty file in place of the miner program. This will obviously prevent the miner from working, but fortunately it's easy to check & fix:

An empty miner file looks like this:

Code:

ls -la  /opt/bitfury/chainminer/miner
-rwxr-xr-x 1 pi pi 0 Oct  2 10:05 /opt/bitfury/chainminer/miner

If your miner doesn't work and you can see an empty file like above, just run this and wait for the compilation process (~5 minutes):

Code:

cd /opt/bitfury/chainminer && sudo make clean && sudo make

[darkfriend77]

Added:

...
4. How to fix an empty miner File?
...
4. How to fix an empty miner File?

I've heard of three people in the last 24 hours who received their miners with an empty file in place of the miner program. This will obviously prevent the miner from working, but fortunately it's easy to check & fix:

An empty miner file looks like this:

Code:

ls -la  /opt/bitfury/chainminer/miner
-rwxr-xr-x 1 pi pi 0 Oct  2 10:05 /opt/bitfury/chainminer/miner

If your miner doesn't work and you can see an empty file like above, just run this and wait for the compilation process (~5 minutes):

Code:

cd /opt/bitfury/chainminer && sudo make clean && sudo make

...

[GandalfG]

Guys, looking for someone with a version 1 M board and successfully running 4 or more H cards

I have 4 cards, without problems most of the time. More are arriving later today.

wow, I have two stubborn version 1 M boards, that just wont hash properly with more than 3 H cards.

 What is your hashrate with 4 cards? Are you using the chainminer that came with the board? Any special settings? Thanks in advance.

138.5 GH total, but 3 chips are dead (2 bypassed and 1 at the end of the chain). I overvolted them to an average of 0.78v. I'm using the stock software. Autotune is off, and some chips are set to 54 and some to 55, based on manual testing.

That's cool. I get 115GH/s with 3 H-boards. The moment I add the fourth it falls to 84GH/s. Using stock software, tried  both Autotune on and off. I guess I will have to dig deeper. Hashrate starts off good after power on and falls down within a minute or so.   Thanks for your help though

I have identical problem.
3  card  work without problem. When add fourth falls to 12Gh/s
Where I can define how many card I have ?

[ricolein]

Hi,

two days ago i got my rig, and it works fine (after solving zero-byte-bug). Today in the morning i see three cards are not working, down to 0GHash. I swaped them to other slots. Two start mining, but slow with 10Ghash and one is still dead. Even in other slots. It just produces errors and think it have just 9(!) chips, not 16:

Code:

113	AIfDSo	54	0.000	0.042	0	2748	0	0	4	[7:0]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	77 29 0 0 0 156 260 263 263 263 263 263 263 263 262 123 
114	AIfDSo	54	0.000	0.032	0	306	0	0	3	[7:1]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	1 1 0 0 0 18 51 4 28 59 11 28 8 26 70 1 
115	AIfDSo	54	0.000	0.032	0	1535	0	0	3	[7:2]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	28 59 127 234 206 175 109 0 28 59 99 175 136 32 68 0 
116	AIfDSo	54	0.000	0.053	0	1592	0	0	5	[7:3]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	0 0 0 0 164 228 228 226 65 0 162 226 65 162 66 0 
117	AIfDSo	54	0.000	0.032	0	1087	0	4	3	[7:4]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	0 0 0 0 81 137 0 0 81 216 217 137 0 81 137 0 
118	AIfDSo	54	0.000	0.032	0	1115	0	0	3	[7:5]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	0 56 253 253 0 0 0 253 252 0 0 0 48 0 0 0 
119	AIfDSo	54	0.000	0.032	0	1683	0	0	3	[7:6]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	58 0 0 0 216 280 68 0 0 216 279 279 67 1 215 4 
120	AIfDSo	54	0.000	0.000	0	0	0	2	0	[7:7]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 
121	AIfDSo	54	0.000	1.120	0	2706	12	3	106	[7:8]	756	0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 	14 224 324 324 312 106 4 14 280 291 224 147 112 110 116 104 
122	AIfDSo	54	0.644	2.008	45	55	0	0	190	[8:0]    <= here starts next board

Any ideas i can do to bring at least the other two boards back to full life? At the moment i hope for self-healing-effects and let it run.

Ciao

Rico

[puffmais]

Hi everybody..

my 8 Cards are running the last weeks very stable and with no problems. now after a reboot, the put.log shows that i have 12 boards and many miso and spi errors...
i have changed the m-boards, but same results. i also installed the miner new. someone has an idea?!

[server]

Hi everybody..

my 8 Cards are running the last weeks very stable and with no problems. now after a reboot, the put.log shows that i have 12 boards and many miso and spi errors...
i have changed the m-boards, but same results. i also installed the miner new. someone has an idea?!

I had the same experience and I contacted punin for this.
He will receive 2 M-boards from me this week (tomorrow/Tuesday) so he can investigate what's going on.

[klondike_bar]

Hi everybody..

my 8 Cards are running the last weeks very stable and with no problems. now after a reboot, the put.log shows that i have 12 boards and many miso and spi errors...
i have changed the m-boards, but same results. i also installed the miner new. someone has an idea?!

I had the same experience and I contacted punin for this.
He will receive 2 M-boards from me this week (tomorrow/Tuesday) so he can investigate what's going on.

sounds like it may be an issue on the sd card image? have you installed the newest chainminer?

[mighq]

with only 1 H-board in place drawing 45W, can I only use 1x 6pin PCI-E power cable instead of 2 of them? if so. which one, left or right?

[Micky25]

I have 16 cards on a V1 M-board.  It runs reasonably well most of the time.  I would prefer to upgrade to a V2 so I can at least update chainminer and reduce errors but no love yet. 

According to goxed you should be able to get the newest chainminer running on V1 boards rather easily.
https://bitcointalk.org/index.php?topic=251966.msg3372344#msg3372344

[Cablez]

Oooh  I will have to give this a try tomorrow.

[jddebug]

Oooh  I will have to give this a try tomorrow.

Cablez,

Please let me know how it goes and if it indeed increases your hashrate.

Thanks