gerask0
Newbie
 Offline
Activity: 258
Merit: 0
|
 |
August 07, 2018, 08:19:54 AM |
|
have few cards 1080, and when start it togather on phi2 algo, two of them have lower hash than other, but if i start each card separately, they show the same hashrate
|
|
|
|
|
|
|
|
|
|
|
|
|
|
No Gods or Kings. Only Bitcoin
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
gerask0
Newbie
Offline
Activity: 258
Merit: 0
|
|
August 07, 2018, 08:20:20 AM |
|
in any case is the best miner for phi2
|
|
|
|
|
|
Saphire
|
|
August 07, 2018, 09:31:07 AM |
|
i like this miner  |
|
|
|
|
|
dragonmike
|
|
August 07, 2018, 10:58:58 AM |
|
Your performance figures on Neoscrypt are a little optimistic...
Using latest nVidia drivers, I get 1230 Mh/s on my 1080's at +110/+500 (vs 1330-1390 advertised above). Intensity at default (6).
...is anyone able to tell me what I'm doing wrong here or is the advertised speed really bogus? Or at 130% pl with 200+ overclocks?...   Increase the intensity. Excavator 1.4.4a is still the best miner for neoscrypt. Isn't 6 the highest already? Yeah I know Excavator is good. But I'd rather not use Nicehash if I have the choice. Anyways, that Neoscrypt coin I was looking at turned out to be shit, so back to the drawing board!  |
|
|
|
|
nitrobg
Member
Offline
Activity: 413
Merit: 17
|
|
August 07, 2018, 11:33:54 AM |
|
Your performance figures on Neoscrypt are a little optimistic...
Using latest nVidia drivers, I get 1230 Mh/s on my 1080's at +110/+500 (vs 1330-1390 advertised above). Intensity at default (6).
...is anyone able to tell me what I'm doing wrong here or is the advertised speed really bogus? Or at 130% pl with 200+ overclocks?... Increase the intensity. Excavator 1.4.4a is still the best miner for neoscrypt. Isn't 6 the highest already? Yeah I know Excavator is good. But I'd rather not use Nicehash if I have the choice. Anyways, that Neoscrypt coin I was looking at turned out to be shit, so back to the drawing board! Excavator 1.4.4a can be used on other pools as well. Try increasing intensity of CD, you should be able to get 1.8+MH/s. |
|
|
|
|
flameelement
Newbie
Offline
Activity: 4
Merit: 0
|
|
August 07, 2018, 05:07:14 PM |
|
What is exactly parameter to see it in console? |
|
|
|
|
rgzrgz
Member
Offline
Activity: 151
Merit: 10
|
|
August 07, 2018, 05:25:25 PM |
|
Failover pools please! In miner.cfg or config.txt
|
|
|
|
|
johnreese5895
Newbie
Offline
Activity: 56
Merit: 0
|
|
August 07, 2018, 07:00:51 PM |
|
This miner is awesome for phi2  |
|
|
|
|
ggillies
Newbie
Offline
Activity: 19
Merit: 0
|
|
August 07, 2018, 09:46:58 PM |
|
WOW!!!!! Phi2 on 0.8.3 is SMOKING fast!!! I'm at 9.8 MH/s per card for my 1080tis ... Holy COW!
how about power consumption? I am at 100% power, +75 GPU and +150 Mem clock. 8 X Nvidia 1080ti cards, Awesomeminer on Windows 10, latest NVIDIA drivers. Cheers. |
|
|
|
|
|
cryptodredge (OP)
|
|
August 07, 2018, 10:20:42 PM |
|
0.8 to 0.8.2 was a big boost on lyra2z for the gtx1070 (2500 kh/s to 3200 kh/s)
However, 0.8 to 0.8.2 the hashrate regressed on lyra2z for the gtx1070ti (3300 kh/s to 2700 kh/s)
love the improvements. However since 0.8.2 my 1070 greatly outperforms my 1070ti's on Lyra2z. 1070 avg hash 3954 KH/s 1070ti avg hash 3220 KH/s any ideas how? I've got 4 different 1070ti's and none come close to my normal 1070....  Could you check v0.8.3? It's better now thanks, but the 1070 is still doing much better than the 1070ti's [08:35:47] INFO - GPU0 Gigabyte GTX 1070 Ti : 3395KH/s (Avr 3399KH/s) : 22.32KH/W : T=67C Fan=80% [08:35:47] INFO - GPU1 EVGA GTX 1070 Ti : 3405KH/s (Avr 3407KH/s) : 22.47KH/W : T=66C Fan=80% [08:35:47] INFO - GPU2 Zotac GTX 1070 Ti : 3383KH/s (Avr 3386KH/s) : 23.55KH/W : T=66C Fan=80% [08:35:47] INFO - GPU3 Gigabyte GTX 1070 Ti : 3405KH/s (Avr 3399KH/s) : 22.40KH/W : T=66C Fan=80% [08:35:47] INFO - GPU4 MSI GTX 1070 : 3973KH/s (Avr 3981KH/s) : 23.20KH/W : T=63C Fan=80% [08:35:47] INFO - GPU5 Gigabyte GTX 1060 6GB : 2833KH/s (Avr 2829KH/s) : 21.35KH/W : T=65C Fan=80% [08:35:47] INFO - Total hashrate 20.40MH/s Thanks for your report. We'll try to figure out why it's happening |
CryptoDredge: NVIDIA GPU Miner
|
|
|
|
cryptodredge (OP)
|
|
August 07, 2018, 10:27:03 PM |
|
Is it possible to set PL/tdp in bat file? without MSI afterburner? like in ccminer we can use --plimit , is there anything similar here that we can use?
Unfortunately, it is not possible yet. The task was created. Thanks for your suggestion |
CryptoDredge: NVIDIA GPU Miner
|
|
|
Miro1764n
Member
Offline
Activity: 232
Merit: 11
|
|
August 09, 2018, 12:12:48 AM |
|
have few cards 1080, and when start it togather on phi2 algo, two of them have lower hash than other, but if i start each card separately, they show the same hashrate
Your CPU is too slow or you do not have enough system memory. |
|
|
|
|
Drifttap
Newbie
Offline
Activity: 2
Merit: 0
|
|
August 09, 2018, 04:02:59 AM |
|
have few cards 1080, and when start it togather on phi2 algo, two of them have lower hash than other, but if i start each card separately, they show the same hashrate
Your CPU is too slow or you do not have enough system memory. This problem only occurs on Crypto dredge from my experiences. Don't go changing your whole hardware configuration on something that came with a miner update. I believe the dev has already said he will be focusing on this issue in the coming updates. |
|
|
|
|
|
Coin++
|
|
August 09, 2018, 07:22:56 AM |
|
A Linux version for Cuda 8 ?
|
|
|
|
gerask0
Newbie
Offline
Activity: 258
Merit: 0
|
|
August 09, 2018, 02:05:33 PM |
|
have few cards 1080, and when start it togather on phi2 algo, two of them have lower hash than other, but if i start each card separately, they show the same hashrate
Your CPU is too slow or you do not have enough system memory. 7700k 8gb |
|
|
|
|
Saponetta
Newbie
Offline
Activity: 28
Merit: 0
|
|
August 09, 2018, 03:50:24 PM |
|
Any tips on how to increase stability with this miner?
I often get the 1 gpu to reset to default in afterburner then it ends up rebooting the rig. (tried both lowering the intensity and without overclock, basically only kept PL to 75%)
ty
|
|
|
|
|
ripcurrent
Member
Offline
Activity: 160
Merit: 10
|
|
August 11, 2018, 02:35:01 AM |
|
It there a way to change the frequency of the hash rate report, for tuning purposes?
|
|
|
|
|
jebidia
Jr. Member
Offline
Activity: 161
Merit: 1
|
|
August 11, 2018, 02:41:32 AM |
|
Rock solid for me. On phi2: Evga sc 60 tdp +150 core 0 mem gets around 8.5 mh..gigabyte cards at tdp 60 core +200 mem 0 gets close to the evga
|
|
|
|
|
UpWind
Newbie
Offline
Activity: 28
Merit: 0
|
|
August 11, 2018, 08:09:23 AM |
|
Helloi I am under ubuntu 16.04 with cuda 9.2 Downloaded and run the latest version (803) but is giving an error: $ sudo bash runlyra.sh
./CryptoDredge: error while loading shared libraries: libcares.so.2: cannot open shared object file: No such file or directory
': not a valid identifier `continueKey Do you know what can I do? |
|
|
|
|
|
cryptodredge (OP)
|
|
August 11, 2018, 09:59:04 AM |
|
Helloi I am under ubuntu 16.04 with cuda 9.2 Downloaded and run the latest version (803) but is giving an error: $ sudo bash runlyra.sh
./CryptoDredge: error while loading shared libraries: libcares.so.2: cannot open shared object file: No such file or directory
': not a valid identifier `continueKey Do you know what can I do? Installing libc-ares2 package is as easy as running the following command on terminal: sudo apt-get install libc-ares2 |
CryptoDredge: NVIDIA GPU Miner
|
|
|
|
