KanoPool since 2014 🐈 - PPLNS and Solo 0.5% fee - Worldwide - 2436 blocks

[perfectplus174]

My avalons don't seem very consistent. I'm running 11 A6's and my shift graph has huge spikes of high and low and inconsistency. My S7's are almost dead on though. I've even ran the A6's through 3 separate controllers to see if that would help and nada. Maybe that's how they are supposed to run, I don't know.

https://imgur.com/MD1CFHY

My 741's are very consistent. However, once enough time elapses the graphs changes its Y value increments to much smaller units, therefore you'll see what look like larger variations of hash rate although it is fluctuating fractions of a GHS.

Have you looked at the image of my shift graph? I was wondering if it was normal, but you can see my S7's at the bottom are very consistent as well.

Yes, however your screenshot omits the most important data which is the Y axis value interval.

It still shows the average on the right side for comparison of TH/s intervals......
Here is a better pic though to make it easier to read.
https://imgur.com/a/24QxZ

Ok yeah, excuse me for that I guess I wasn't looking close enough. Are you certain you've got no power issues? That variation is crazy. CRAY Z.

In other news, its been a bit since I've seen any really comitted dancing. Dancing is an important ingredient, here.

I can basically guarantee we'll hit a block in the next hour. "basically".

I don't think I have any power issues.....I'm running 2400 watt PSU with breakout board (I think that's what it is, I'm still green) to run 2 miners at a time. They A6 is rated at 1080 watts each. Something is up and it's interesting and annoying.
https://imgur.com/a/gFFL5

[1715432100]

1715432100

[Norm49]

What? Did you say something? I couldn't hear you.   

So wait, does that mean if I put it in the bedroom I won't hear my other half's snoring?!?   Hmm, might be time to move the miner... 

Come on Kano poolites - let's solve the block!!!

After listening to the latest batch of S9's winding up and down like a dragster blower motor in my other upstairs bedroom with all the doors closed in between, I don't think you'd hear the other half...but I've come to appreciate the snoring sound....

[clgrissom3]

Guys, is this even ok..?

https://imgur.com/a/4d69D

So many HW errors within 36 hours. Never seen it at this much before. You can also see my miner is jumping between different stratums of Kano.

Is my miner too cold..? Could a faaaaar location of Kano stratum create this..? Am I doing something wrong..? I double checked my connection fyi, it is all ok.

I wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

[2tights]

I don't think I have any power issues.....I'm running 2400 watt PSU with breakout board (I think that's what it is, I'm still green) to run 2 miners at a time. They A6 is rated at 1080 watts each. Something is up and it's interesting and annoying.
https://imgur.com/a/gFFL5
[/quote]

I have two 1300 watt EVGA power supplies for each 741 with no issues. I don't think you can scratch a power issue off the list of possible causes.

[2tights]

Guys, is this even ok..?

https://imgur.com/a/4d69D

So many HW errors within 36 hours. Never seen it at this much before. You can also see my miner is jumping between different stratums of Kano.

Is my miner too cold..? Could a faaaaar location of Kano stratum create this..? Am I doing something wrong..? I double checked my connection fyi, it is all ok.

I wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

[manduul]

Guys, is this even ok..?

https://imgur.com/a/4d69D

So many HW errors within 36 hours. Never seen it at this much before. You can also see my miner is jumping between different stratums of Kano.

Is my miner too cold..? Could a faaaaar location of Kano stratum create this..? Am I doing something wrong..? I double checked my connection fyi, it is all ok.

I wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

That's what I thought and I kept checking Kano page. My has was registering really low, like 11Th/s. I thought it was my connection, and I checked everything it all seemed ok. I mean, my connection is ok, because I'm here talking to you guys right

On Kano's Workers page, under the Invalid it says 0.393%. Is it all cool?

Well, my S9 seems to be ok now. Not jumping between Kano stratums for the last 30 min or so. I'll just leave it there. Thanks man.

[manduul]

Guys, is this even ok..?

https://imgur.com/a/4d69D

So many HW errors within 36 hours. Never seen it at this much before. You can also see my miner is jumping between different stratums of Kano.

Is my miner too cold..? Could a faaaaar location of Kano stratum create this..? Am I doing something wrong..? I double checked my connection fyi, it is all ok.

I wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

Damn. I need a heater for this baby then. I feel like I live in an opposite world haha.

[Runes911]

My avalons don't seem very consistent. I'm running 11 A6's and my shift graph has huge spikes of high and low and inconsistency. My S7's are almost dead on though. I've even ran the A6's through 3 separate controllers to see if that would help and nada. Maybe that's how they are supposed to run, I don't know.

https://imgur.com/MD1CFHY

My 741's are very consistent. However, once enough time elapses the graphs changes its Y value increments to much smaller units, therefore you'll see what look like larger variations of hash rate although it is fluctuating fractions of a GHS.

Have you looked at the image of my shift graph? I was wondering if it was normal, but you can see my S7's at the bottom are very consistent as well.

Yes, however your screenshot omits the most important data which is the Y axis value interval.

It still shows the average on the right side for comparison of TH/s intervals......
Here is a better pic though to make it easier to read.
https://imgur.com/a/24QxZ

Ok yeah, excuse me for that I guess I wasn't looking close enough. Are you certain you've got no power issues? That variation is crazy. CRAY Z.

In other news, its been a bit since I've seen any really comitted dancing. Dancing is an important ingredient, here.

I can basically guarantee we'll hit a block in the next hour. "basically".

https://media0.giphy.com/media/bDw4vijOi28OQ/giphy.gif

I don't think I have any power issues.....I'm running 2400 watt PSU with breakout board (I think that's what it is, I'm still green) to run 2 miners at a time. They A6 is rated at 1080 watts each. Something is up and it's interesting and annoying.
https://imgur.com/a/gFFL5

Your mention an A6 but your screen shot is an S9. Are you powering both? If so, I bet it is your power. S9 = 1370 and you say an A6 is 1080, thats 2450. For a 2400w you shouldn't be using more than 1920. (80% rule) Though if you are on 220V ignore all of what I just said.

[perfectplus174]

My avalons don't seem very consistent. I'm running 11 A6's and my shift graph has huge spikes of high and low and inconsistency. My S7's are almost dead on though. I've even ran the A6's through 3 separate controllers to see if that would help and nada. Maybe that's how they are supposed to run, I don't know.

https://imgur.com/MD1CFHY

My 741's are very consistent. However, once enough time elapses the graphs changes its Y value increments to much smaller units, therefore you'll see what look like larger variations of hash rate although it is fluctuating fractions of a GHS.

Have you looked at the image of my shift graph? I was wondering if it was normal, but you can see my S7's at the bottom are very consistent as well.

Yes, however your screenshot omits the most important data which is the Y axis value interval.

It still shows the average on the right side for comparison of TH/s intervals......
Here is a better pic though to make it easier to read.
https://imgur.com/a/24QxZ

Ok yeah, excuse me for that I guess I wasn't looking close enough. Are you certain you've got no power issues? That variation is crazy. CRAY Z.

In other news, its been a bit since I've seen any really comitted dancing. Dancing is an important ingredient, here.

I can basically guarantee we'll hit a block in the next hour. "basically".

I don't think I have any power issues.....I'm running 2400 watt PSU with breakout board (I think that's what it is, I'm still green) to run 2 miners at a time. They A6 is rated at 1080 watts each. Something is up and it's interesting and annoying.
https://imgur.com/a/gFFL5

Your mention an A6 but your screen shot is an S9. Are you powering both? If so, I bet it is your power. S9 = 1370 and you say an A6 is 1080, thats 2450. For a 2400w you shouldn't be using more than 1920. (80% rule) Though if you are on 220V ignore all of what I just said.

I do not own an S9. Must be a different screen shot.

I believe we're actually running 240V.

[perfectplus174]

I don't think I have any power issues.....I'm running 2400 watt PSU with breakout board (I think that's what it is, I'm still green) to run 2 miners at a time. They A6 is rated at 1080 watts each. Something is up and it's interesting and annoying.
https://imgur.com/a/gFFL5

I have two 1300 watt EVGA power supplies for each 741 with no issues. I don't think you can scratch a power issue off the list of possible causes.
[/quote]

Each PSU is on it's own 30 amp breaker 240V.
So a controller with 4 A6's has two separate PSU's.
I have 3 controllers total running 11 A6's yet on the shift graph, they seem to follow the same pattern as far as when they dip. I noticed one of the S7's does as well. Could it be internet connection? They are all running to a ported switch, maybe it's acting up? Just guessing. I'm clueless here, doesn't make sense to me.

[bigolin]

Guys, is this even ok..?

https://imgur.com/a/4d69D

So many HW errors within 36 hours. Never seen it at this much before. You can also see my miner is jumping between different stratums of Kano.

Is my miner too cold..? Could a faaaaar location of Kano stratum create this..? Am I doing something wrong..? I double checked my connection fyi, it is all ok.

I wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

For reference what are we calling "Too cold". Less than 70? Less than 60? I still have no idea where everyone else's system runs. Lately my 4 s9's have been enjoying the cold snowy air in Arkansas and the spread ranges from 62c chip temp to 77c chip temp at the moment.

[2tights]

wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

For reference what are we calling "Too cold". Less than 70? Less than 60? I still have no idea where everyone else's system runs. Lately my 4 s9's have been enjoying the cold snowy air in Arkansas and the spread ranges from 62c chip temp to 77c chip temp at the moment.

My best hash rate is right around 80-83 degrees.

Anything less than 75 and  they're losing 20% of the hashrate. They seem happy to chill around 80-82 degrees with fans around 4500 to 5400 rpm

[perfectplus174]

wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

For reference what are we calling "Too cold". Less than 70? Less than 60? I still have no idea where everyone else's system runs. Lately my 4 s9's have been enjoying the cold snowy air in Arkansas and the spread ranges from 62c chip temp to 77c chip temp at the moment.

My best hash rate is right around 80-83 degrees.

Anything less than 75 and  they're losing 20% of the hashrate. They seem happy to chill around 80-82 degrees with fans around 4500 to 5400 rpm

That's interesting....Mine are in the 59 to 61 range. I wonder if that has anything to do with it? I need to monitor carefully because during the day we have a window open and the high cfm fan sucks a lot of heat out. In the evening, we lock it down and the room runs warmer. I've noticed my hash seems to do better in the top right corner of Kano when I monitor it from home (windows shut).

I will be doing a little recon into this now and collecting some data. Thanks for the info, I'll see if it holds true over here.

[2tights]

wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

For reference what are we calling "Too cold". Less than 70? Less than 60? I still have no idea where everyone else's system runs. Lately my 4 s9's have been enjoying the cold snowy air in Arkansas and the spread ranges from 62c chip temp to 77c chip temp at the moment.

My best hash rate is right around 80-83 degrees.

Anything less than 75 and  they're losing 20% of the hashrate. They seem happy to chill around 80-82 degrees with fans around 4500 to 5400 rpm

That's interesting....Mine are in the 59 to 61 range. I wonder if that has anything to do with it? I need to monitor carefully because during the day we have a window open and the high cfm fan sucks a lot of heat out. In the evening, we lock it down and the room runs warmer. I've noticed my hash seems to do better in the top right corner of Kano when I monitor it from home (windows shut).

I will be doing a little recon into this now and collecting some data. Thanks for the info, I'll see if it holds true over here.

gl man. Yeah I have mine in a shop, separate building than my home. Its small, only 120 sf with a 9' ceiling on a 4/12 pitch for a total volume of around 1000 cubic ft. I started leaving the window open a little but noticed that if it got too cold they lag.  let me know if you want any other infoz

[weronixa]

wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

For reference what are we calling "Too cold". Less than 70? Less than 60? I still have no idea where everyone else's system runs. Lately my 4 s9's have been enjoying the cold snowy air in Arkansas and the spread ranges from 62c chip temp to 77c chip temp at the moment.

My best hash rate is right around 80-83 degrees.

Anything less than 75 and  they're losing 20% of the hashrate. They seem happy to chill around 80-82 degrees with fans around 4500 to 5400 rpm

This doesn't seem to be true for my s9. This is 24h on the balcony in Sweden: https://imgur.com/YMWbQAS

[2tights]

Time for a reboot?

[VRobb]

@ only 127+% diff??  Hardly, eat some chicken instead!! 

[2tights]

@ only 127+% diff??  Hardly, eat some chicken instead!! 

LoLz how about a chicken dance?

[perfectplus174]

wouldn't worry too much about what you see on your S9s...that's been doctored by Biteme in BMminer.  I would focus on the errors shown on the Kano Workers page and then only to verify that it is close or lower than the Invalids shown at the top of each Kano page.

I do notice that too cold is bad.

For reference what are we calling "Too cold". Less than 70? Less than 60? I still have no idea where everyone else's system runs. Lately my 4 s9's have been enjoying the cold snowy air in Arkansas and the spread ranges from 62c chip temp to 77c chip temp at the moment.

My best hash rate is right around 80-83 degrees.

Anything less than 75 and  they're losing 20% of the hashrate. They seem happy to chill around 80-82 degrees with fans around 4500 to 5400 rpm

That's interesting....Mine are in the 59 to 61 range. I wonder if that has anything to do with it? I need to monitor carefully because during the day we have a window open and the high cfm fan sucks a lot of heat out. In the evening, we lock it down and the room runs warmer. I've noticed my hash seems to do better in the top right corner of Kano when I monitor it from home (windows shut).

I will be doing a little recon into this now and collecting some data. Thanks for the info, I'll see if it holds true over here.

gl man. Yeah I have mine in a shop, separate building than my home. Its small, only 120 sf with a 9' ceiling on a 4/12 pitch for a total volume of around 1000 cubic ft. I started leaving the window open a little but noticed that if it got too cold they lag.   let me know if you want any other infoz

Looks like I haven't checked the temp in a while. Was showing 39 and 40's !! I shut the window and the room got hot quick, it shut off an S7 that I could feel the heat radiating off of. The Avalons jumped up to 66 and 72 but I opened it back up afte the S7 pooped on me. Now window is open and they are all going. I guess I'm stuck at this for now. I just feel like I'm losing around 8-9 TH/s total based on calculations.
11x A6 @ 3.5 TH/s each +
4x S7 @ 4.73 TH/s each = 57.42 TH/s
I'm showing usually 48.72

All issues coming from the Avalons. Through the controller's page, they are only hashing around 2380-2700 gh/s per machine. Some higher, some lower. I've switched them around, but then that machine will do higher while a different now loses. So confusing. I've given up on this before and it sounds like I'll have to do it again. Hard to to though.

[NotFuzzyWarm]

Dying to pick up a couple of 821s to feed into kanopool, but really want to do my buying through minerwarez.com   They are being very quiet about the new units and it has me wondering?     Other distributors (blokforge etc) are taking pre-orders but minerwarez hasn't even made an announcement.   Is this their typical SOP with new products or should I be jumping horses and going with a new provider and putting up with wire transfers and overseas shipping?  My gut tells me to be patient but I have limited experience all around, and with them in particular, to go on.   My one single order with them went perfect by the way.

Just curious...

So perhaps ask in the Minerwarez thread?