oeps, my bad, didn't saw that Thanks!  I just see that thread too  |
|
|
|
Nice, new thread  |
|
|
|
Can't wait to test new patch for cgminer 3.11.0 Tomorrow Nice  are the dupes on chip 1 (or 0) fixed with that? Yeas and a lot more fixes and speed ups great! is it released?  Not yet |
|
|
|
Can't wait to test new patch for cgminer 3.11.0 Tomorrow Nice |
|
|
|
Can't wait to test new patch for cgminer 3.11.0 |
|
|
|
I messed up everything now I can't even mine anymore, I am getting a error saying "warning proxy getwork_listener.render_POST # Authorization required"
Any idea what did I mess up now?
All was working fine before i tried to add ppc pool, so I deleted and downloaded all again start from scratch but still getting same error :-(
That was normal message. Check again the username & password. Did you test again with btcguild or still in PPC pool? I just edit HEXMiner.ini file & save it. It work fine, so i wonder why your saving not working. Some making a mistake by saving to txt file. To avoid this just set the windows setting to open .ini file using notepad. You can write on HEXMINER too, but username & password won't save unless you start the miner |
|
|
|
Thanks Zich, its good to have for next time I compile CG. |
|
|
|
i configured 1000mV when then HEX16A2 went down to 5GH/s, at the moment i configured 1100mv and it did not happen again yet. Maybe it the lower voltage could make it unstable!?
Bye
Michael
Hmm, i had been playing with various setting but never had similar problem. At least your miner already stable right now |
|
|
|
What other software and hardware are you using to mine ataa coins?
Most of us dont't mine alt coins. Because it isn't worth. But if want to mine with p2pool i think its the best choice to use linux an cgminer 3.10 with patch from technobit. Hmmmm... Going to try this weekend with Rasp PI Tks That's better |
|
|
|
Just arrived!!!
Now the fight is to get the excessive postage somehow, because we paid 132€ of postage for a urgent service never provided.
Marto74, actually is doing some improvement on the client assistance now and I think that's the good way to do it.
Gratzs, that was big package |
|
|
|
Super, Just an advise use latest cgminer 3.10.0 the patch is available on technobit site. You will do it like piece of cake. Apart of jokes 3.6.1 is buggy it is highly recommended to switch to latest I could not see a download patch for 3.10.0, does the 3.6.1 patch work on 3.10 ? not that it matters as am still waiting on boards, but nice to know should they ever turn up.. Patch for 3.6.1 wil not work on other version or vice versa. Patch for cgminer 3.10.0 that uploaded by technobit 0.1.5or Uploaded by me that work with wget command https://www.dropbox.com/s/5fgzi8sux0qltlm/87f0213112a3c69e2c55160b9c674b9de2cde996_u.patch |
|
|
|
180% means not what you think humans us command free otherwise read what it exactly means Yeah, but seeing 180% everyday make me worried |
|
|
|
Can anyone confirm I can run ~20 or so boards with the TP-Link MR3020, with two 10port powered USB2 hubs on piggyback ?
Thanks.
I am not sure about this since i don't had that many board. But i am more prefer to buy another TL-ML3020 since the price is very cheap. With 2 HEX16A & 1 HEX16C, my TL-ML3020 memory usage already at 156%. Add 2 nanofury memory usage reach 180%. I don't think memory might be an issue. I've got 7 HEX16A2 running and doesn't seem like it's hampering performance. I'd still limit it to 10 per router though. To be on the safe side. Yes, but i just don't like pushing the router that hard. That why my 2 nanofury moved to tablet now. |
|
|
|
Can anyone confirm I can run ~20 or so boards with the TP-Link MR3020, with two 10port powered USB2 hubs on piggyback ?
Thanks.
I am not sure about this since i don't had that many board. But i am more prefer to buy another TL-ML3020 since the price is very cheap. With 2 HEX16A & 1 HEX16C, my TL-ML3020 memory usage already at 156%. Add 2 nanofury memory usage reach 180%. |
|
|
|
Same error here but one from six board. Helps only when i shut down the psu. Other five board work well with 20gh. Hi,
my HEX16A2, which was delivered on thursday, went down from about 20HG/s to 5HG/s last night. It did that for the third time. I have a powered USB HUB and a 600W power supply, that is only for this miner. Restart of cgminer does not help, when i turn off the 12v and then turn it on again, the miner goes back to normal work. Is there a command to reset the miner hardware?
Bye
Michael
No Idea on that one? You can test the problem board without usb hub to see the behavior. Did the powered usb hub use same power source as the miner? What is your usb hub brand? Some of us encounter problem with usb hub that use stt chip. It had the same problem without hub, direct connected to the pi, that was why i added the hub. Hmm, let me test with my pi later. Result: I had been test HEX16C on pi whole night. It work well except for chip 0 nonce problem i guess since hash rate decrease from 23 GH/s to 20 Gh/s. You need to test the board on other host, PC maybe just to make sure the board status.  |
|
|
|
Same error here but one from six board. Helps only when i shut down the psu. Other five board work well with 20gh. Hi,
my HEX16A2, which was delivered on thursday, went down from about 20HG/s to 5HG/s last night. It did that for the third time. I have a powered USB HUB and a 600W power supply, that is only for this miner. Restart of cgminer does not help, when i turn off the 12v and then turn it on again, the miner goes back to normal work. Is there a command to reset the miner hardware?
Bye
Michael
No Idea on that one? You can test the problem board without usb hub to see the behavior. Did the powered usb hub use same power source as the miner? What is your usb hub brand? Some of us encounter problem with usb hub that use stt chip. |
|
|
|
Derped on the password. Thanks.
Great |
|
|
|
Thanks Zilch.
BTW, is there any way to switch pools?
Tried entering a PPC pool credentials via the web login page. It keeps going back to the backup BTC pool.
If you already put it in pool 1, then maybe there is problem with the pool. You can see pool status by typing "p" on cgminer window. |
|
|
|
I see. Currently patching and building Cgminer 3.8.3 on Minepeon. Hope it does work.
cgminer 3.8.3 using patch: 7ddb94d6964f2451d2e76f70b069dfdf2b3d4d6f.patch Got it running.  Finally. Gratz |
|
|
|
|
Show Posts
