|
MistGold
|
 |
December 06, 2017, 11:57:02 PM |
|
What settings for getting 700kh/s for neoscrypt on RX570 ? Overclocked.
|
|
|
|
|
zawawa (OP)
Sr. Member
 Offline
Activity: 728
Merit: 304
Miner Developer
|
|
December 07, 2017, 12:08:20 AM |
|
Dear zawawa, please consider failover pools for DevFee. 1.1.3 hangs now in devfee loop because nicehash is down. Thanks again for your DevPower.  Will do. I'm out of town right now. I will fix this tomorrow. I suppose I left NiceHash at the right timing... |
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ |
|
|
|
UnclWish
|
|
December 07, 2017, 05:18:49 PM
Last edit: December 09, 2017, 10:28:11 PM by UnclWish |
|
zawawa, I set up the custom pool and I need non "x" password. I entered it into password field, but in connection GGS use "x" password. Maybe it's because of my password type... I entered password like this: MyRig:email@server.org
Can you look at that?
|
|
|
|
|
agrld
Newbie
Offline
Activity: 15
Merit: 0
|
|
December 08, 2017, 10:18:37 AM |
|
hi, my miner always stuck at 15 min. is it because devfee ?
|
|
|
|
|
|
nerdralph
|
|
December 08, 2017, 05:55:37 PM |
|
Looks like you're doing some good work. Won't be trying the miner since all my rigs are Linux, but I might experiment with your kernels.
|
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
December 08, 2017, 06:10:48 PM |
|
hi, my miner always stuck at 15 min. is it because devfee ?
Yes. I am implementing fail-over pools for the DEVFEE now. Sorry about the delay. The NiceHash debacle happened right after I got out of the country on a business trip. The timing is so uncanny... |
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ |
|
|
kedes
Newbie
Offline
Activity: 34
Merit: 0
|
|
December 09, 2017, 12:02:04 PM |
|
Hello. With this miner all my cards give twice less hasrate on PASCAL algorithm than it should be. GTX 1070 gives 480Mh/s instead 900Mh/s. GTX 1060 gives 250Mh/s instead 580Mh/s.
What's wrong?
|
|
|
|
|
Trimegistus
Legendary
Offline
Activity: 1564
Merit: 1027
|
|
December 09, 2017, 08:14:40 PM |
|
Yes. I am implementing fail-over pools for the DEVFEE now.
Sorry about the delay. The NiceHash debacle happened right after I got out of the country on a business trip.
The timing is so uncanny...
DevFee cause occasional problems indeed. Automatic failover might be a good solution. Nicehash became too big and apparently a bit sloppy... |
|
|
|
|
UnclWish
|
|
December 09, 2017, 09:13:49 PM |
|
DevFee cause occasional problems indeed. Automatic failover might be a good solution. Nicehash became too big and apparently a bit sloppy...
Where did you fall from? Nicehash several days didn't work at all. It's hacked and closed. |
|
|
|
|
|
nerdralph
|
|
December 09, 2017, 10:10:56 PM |
|
Just finished looking at your ethash_pascal kernel. It looks like you partition the work so 1 of the 4 SIMD units in each CU is used for Pascal, and the other 3 is used for Ethereum. Is that correct?
I think you should be able to saturate the L2 interface with just 2 of the 4 SIMD units per CU, which would give you double the performance for Pascal.
|
|
|
|
|
|
UnclWish
|
|
December 09, 2017, 10:26:04 PM |
|
And I think it's time to add neoscrypt. Please, add it.
|
|
|
|
|
SirOverdose
Newbie
Offline
Activity: 13
Merit: 0
|
|
December 10, 2017, 11:02:28 AM |
|
gateless gate gives when i start it:
Unhandled Thread Exception: Index was outside the bounds of the array. at GatelessGateSharp.MainFormJnitializeDevicesO
at GatelessGateSharp.MainForm.MainForm_Load(0bject sender, EventArgs e)
at System.Windows.Forms.Form.0nLoad(Eventfl.rgs e) at System.Windows.Forms.Form.0nCreateControl0
at System.Windows.Form5.0ontroI.CreateControl(Boolean flgnoreVisible)
at System.Windows.Forms.Control.CreateControl0
at System.Windows.Forms.Control.WmShowWindow(Message& m) at System.Windows.Form5.0ontrol.WndProc(Message& m)
at System.Windows.Forms.Form.WmShowWindow(Message& m)
at System.Windows.Forms.NativeWindow.Callback(lntPtr hWnd, lnt32 msg, lntPtr wparam, lntPtr lparam)
I have 11 rx480s on the latest 17.11.4 drivers. Can you tell me what is wrong? Thanks
|
|
|
|
|
|
UnclWish
|
|
December 10, 2017, 11:51:28 AM |
|
And add info about current pool diffculty please. At least in log.
|
|
|
|
|
|
MistGold
|
|
December 10, 2017, 04:58:28 PM |
|
Can you provide config for neoscrypt 900kh/s for RX570 that you been talking about in other theard? :3
|
|
|
|
|
|
MistGold
|
|
December 10, 2017, 04:59:59 PM |
|
And I think it's time to add neoscrypt. Please, add it.
zawawa already has neoscrypt build O_o |
|
|
|
|
zawawa (OP)
Sr. Member
Offline
Activity: 728
Merit: 304
Miner Developer
|
|
December 10, 2017, 05:06:05 PM |
|
And I think it's time to add neoscrypt. Please, add it.
zawawa already has neoscrypt build O_o You are talking about the original Gateless Gate. I don't provide support for that anymore. He is talking about the new Gateless Gate Sharp. |
Gateless Gate Sharp, an open-source ETH/XMR miner: http://bit.ly/2rJ2x4VBTC: 1BHwDWVerUTiKxhHPf2ubqKKiBMiKQGomZ |
|
|
D37945
Newbie
Offline
Activity: 47
Merit: 0
|
|
December 11, 2017, 03:35:07 AM |
|
Please help a crypto chick out!
Does Gateless Gate Sharp run neoscrypt mining?
Tried running a neoscrypt .bat file on the original Gateless Gate but I keep getting this error-
GPU0: Idle more than 2 minutes, declaring SICK!
GPU still showing activity suggesting a hard hang.
Will not attempt to auto-restart it.
Maybe this error wont show up on Gateless Gate Sharp...
|
|
|
|
|
|
nin3tin
|
|
December 11, 2017, 03:53:39 AM |
|
How to fix this  |
|
|
|
|
agrld
Newbie
Offline
Activity: 15
Merit: 0
|
|
December 11, 2017, 05:21:41 AM |
|
GGW became really lag after start, cant event stop mining & need to force close. Tried reinstall and extract to new directory still face same issues. any way to fix this ? thx
|
|
|
|
|
m1n1ngP4d4w4n
Full Member
Offline
Activity: 224
Merit: 100
CryptoLearner
|
|
December 11, 2017, 05:27:15 AM |
|
Please help a crypto chick out!
Does Gateless Gate Sharp run neoscrypt mining?
Tried running a neoscrypt .bat file on the original Gateless Gate but I keep getting this error-
GPU0: Idle more than 2 minutes, declaring SICK!
GPU still showing activity suggesting a hard hang.
Will not attempt to auto-restart it.
Maybe this error wont show up on Gateless Gate Sharp...
Read the post just above yours, you'll get your answer, or the first post of this thread.... |
|
|
|
|
|
Poll
