BkkCoins (OP)
|
|
May 06, 2013, 02:52:08 AM |
|
Right. If the temperature got above a certain limit, we could disable the output of the regulator supplying the ASICs and generate a fault.
As for parts, are we looking at just 85C parts, or are there some you want at 105C?
I was just pricing at 85C commercial parts. I really hope we don't run over about 60-65C. It's mainly the PIC if I recall because I think most of the others are rated higher, but I'd have to double check, and it's very little more for the industrial series. It's not right near an ASIC and generates little heat itself. And the ASICs, well, have no idea what they'll be but assuming they're rated higher since they sure burn the watts.
|
|
|
|
Bicknellski
|
|
May 06, 2013, 03:11:21 AM Last edit: May 06, 2013, 03:23:34 AM by Bicknellski |
|
If you do the heatsink correctly there would be no need to go to higher temp components. Having at look at the therms on the Avalon miner you can see that most of the heat is at the chip and is under 62C + the surrounding board reaches 55C + maybe? If you have the vias designed properly and with what BKKcoins has designed already I don't think we will have issues I hope.
|
|
|
|
|
BkkCoins (OP)
|
|
May 06, 2013, 04:51:07 AM |
|
Oh darn you. Now I have to hold back the cad files until I've earned something for my work.
|
|
|
|
daemondazz
|
|
May 06, 2013, 05:05:50 AM |
|
Don't you need 4 layer?
|
Computers, Amateur Radio, Electronics, Aviation - 1dazzrAbMqNu6cUwh2dtYckNygG7jKs8S
|
|
|
BkkCoins (OP)
|
|
May 06, 2013, 05:17:20 AM |
|
Don't you need 4 layer?
Yes. My tentative plans were to offer 6 products: Board Only and Board w/Parts kit. For each, Klondike 1 - thumb size Klondike 16 - 10x10cm Klondike 64 - 20x20cm Once I have a working prototype I'll start an "OpenBitcoinstore" site to take pre-orders. That way I know how big a PCB batch to run, and how many components. I'll have a bulk order rate for assemblers who want to source everything needed (but ASICs) the easy way. I may offer an pre-assembled "Klondike 1" as well since I figure that's not beyond my means to build here. The rest I'm looking at shipping parts to my home in Canada, packing kits and shipping from both there and across the border in WA state (because Canada Post is too costly for x-border). At least that's my thinking now unless I get talked into some better idea.
|
|
|
|
bassclef
|
|
May 06, 2013, 06:47:19 AM |
|
My tentative plans were to offer 6 products: Board Only and Board w/Parts kit.
For each,
Klondike 1 - thumb size Klondike 16 - 10x10cm Klondike 64 - 20x20cm
I like this idea very much. I would likely order a number of each.
|
|
|
|
turtle83
|
|
May 06, 2013, 07:04:07 AM |
|
Klondike 1 - thumb size
+1 . Horizontal scaling FTW
|
|
|
|
punin
|
|
May 06, 2013, 07:16:24 AM |
|
You might want to stich that ground plane.
|
|
|
|
BkkCoins (OP)
|
|
May 06, 2013, 07:22:56 AM |
|
You might want to stich that ground plane.
Yes, I need to do that. Is there a best practices doc about ideal location and how many? I was going to google it soon but haven't quite got there as I'm setting up the firmware project right now.
|
|
|
|
Bicknellski
|
|
May 06, 2013, 08:08:33 AM |
|
So
8 20 x 20 please. 2 10 x 10 please.
I am looking at housing my farm collocated at a datacenter just to make it easier for myself and cheaper in the long run.
|
|
|
|
Ente
Legendary
Offline
Activity: 2126
Merit: 1001
|
|
May 06, 2013, 09:09:42 AM |
|
What happens when one ASIC dies? Gracefully, like just switching itself off, not burning and creating a crater.. ;-) Will just this ASIC be missing, or all following in the "chain", or the whole board? Would the 64 ASIC board be the same, all following or all 64 fail if one fails?
Seems like burnin's board is not fault tolerant against individual ASIC fails.
Ente
|
|
|
|
punin
|
|
May 06, 2013, 09:35:29 AM |
|
You might want to stich that ground plane.
Yes, I need to do that. Is there a best practices doc about ideal location and how many? I was going to google it soon but haven't quite got there as I'm setting up the firmware project right now. It depends, your PCB manufacturer can comment on that after you send first version of gerbers to them for a quote.
|
|
|
|
BkkCoins (OP)
|
|
May 06, 2013, 09:39:44 AM |
|
What happens when one ASIC dies? Gracefully, like just switching itself off, not burning and creating a crater.. ;-) Will just this ASIC be missing, or all following in the "chain", or the whole board? Would the 64 ASIC board be the same, all following or all 64 fail if one fails?
Seems like burnin's board is not fault tolerant against individual ASIC fails.
Ente
It's hard to say right now without docs. If they are daisy chained then one failed "may" prevent the others after it from working. I say may because it depends on the failure mode. It could just stop hashing correctly, or it could "blow" hard and prevent data from shifting through at all. If they're not chained and have some kind of serial bus then likely one failing would not stop the others but would be a range of nonces that never gets hashed. In both cases one board should not affect other boards and the 64 chip board would be identical to 4 separate 16 chips boards - as that's what it is.
|
|
|
|
Ente
Legendary
Offline
Activity: 2126
Merit: 1001
|
|
May 06, 2013, 10:14:40 AM |
|
What happens when one ASIC dies? Gracefully, like just switching itself off, not burning and creating a crater.. ;-) Will just this ASIC be missing, or all following in the "chain", or the whole board? Would the 64 ASIC board be the same, all following or all 64 fail if one fails?
Seems like burnin's board is not fault tolerant against individual ASIC fails.
Ente
It's hard to say right now without docs. If they are daisy chained then one failed "may" prevent the others after it from working. I say may because it depends on the failure mode. It could just stop hashing correctly, or it could "blow" hard and prevent data from shifting through at all. If they're not chained and have some kind of serial bus then likely one failing would not stop the others but would be a range of nonces that never gets hashed. In both cases one board should not affect other boards and the 64 chip board would be identical to 4 separate 16 chips boards - as that's what it is. Sounds good, thank you! So, it's time for some open-sourcing on side of avalon! :-) Ente
|
|
|
|
fasmax
|
|
May 06, 2013, 11:45:10 AM |
|
Ay ideas on heatsinks ?
|
|
|
|
sensei
|
|
May 06, 2013, 12:13:27 PM |
|
Ay ideas on heatsinks ?
We had a member, Knecke, who was looking into providing them.
|
|
|
|
Bicknellski
|
|
May 06, 2013, 03:05:53 PM |
|
Could be off the rack / shelf alternative laying around in some warehouses in China. Might be worth a look. I have sent out a number of emails on this already. Have heard from one supplier... but would need to ask BKK on what holes required and what sort of mounting arrangement as well. Certainly a lot of people can provide a basic aluminum extruded 10 x 10 heat sink to specifications. That might be just about the easiest part to find I think.
I was also looking at vga after market heatsinks for gpu's with built in fans but again depends on what is possible for mounting and are fans really required?
|
|
|
|
Kuma
Member
Offline
Activity: 107
Merit: 10
|
|
May 06, 2013, 03:25:50 PM |
|
I would order around 10 Klondike 64, but it really depends on price and ETA.
|
|
|
|
sensei
|
|
May 06, 2013, 03:58:29 PM |
|
Do we have enough room to have a 2-3mm keepout zone around the edge so that we can have the option of sliding the card into an edge guide rail instead of stacking?
On 2 sides only of course. In the format your board was presented, it would be the top and bottom.
|
|
|
|
|