The Blocks Factory - Multicoin pool

[lucazane]

Why password recovery does not work? and where is support link?

send me a pm.

[dawgyg]

Will the reward for block finder be coming back anytime soon?

[Maxcielle]

Will the reward for block finder be coming back anytime soon?

 i like this also. at least a bit of thrill

[Mister_E]

Quick question, can I mine this with an sha256 miner?

[dawgyg]

Yes you can by going here:

https://dgb-sha.theblocksfactory.com/

[Mister_E]

Yes you can by going here:

https://dgb-sha.theblocksfactory.com/

Thank for the quick reply! I was told I could not, I thought it was possible myself.

[dawgyg]

Yes you can by going here:

https://dgb-sha.theblocksfactory.com/

Thank for the quick reply! I was told I could not, I thought it was possible myself.

I am currently using my Antminer s7's to mine on the pool. Making over $6 a profit for each one

[Mister_E]

ok, what i have now is a setup:

x79 gigabyte ud3
xeon 2609

2x an r7 370 gpu

ssd with a clean Win 10 install

how can I join a pool? As far as I know I need to install the drivers for the gpu. Then I can use them properly and tune them with afterburner? Then I need to make a .bat file. Where is a guide for this? If I press get started I only get a link to sgminer. I've downloaded it and now I need to set it up to go mining.

Bonus question, could I add a HD6990 to the set?

As you can see, it's for me something to try and expand in the future

[QuintLeo]

The HD 6990 is Terascale, most recent miners expect GCN and either don't work with Terascale cards at all or not very well.

 Since you don't have any RX series cards listed, though, install the 15.12 drivers and try it - worst case the card just won't mine.

[Gil80]

hi.

I just signed up to theblocksfactory and I don't know how to proceed from there.
I have 2 AMD GPU's and I was wondering if it's possible to mine using these GPU's.

In any case, what should I do next to start mining for DIGIBYTE ?

[clackmine]

Why password recovery does not work? and where is support link?

send me a pm.

Could you explain how to make the manual setting of difficulty work correctly? I tried the suffix on my username.workername_diff128 but nothing happened. I'm trying to get a scrypt asic miner to run at difficulty 128 as opposed to 2048, which appears to be the minimum for all my asic miners. Thanks.

[Swimmer63]

Say Lucazane -

I was wondering if we could get the Average Hashrate figures fixed on your DGB SHA-256 pool.  Hard to figure out exactly what our average hash rate is.  Been mining there for a week and given the profitability of DGB looks like I'll be sticking around a while.  As will others.

I don't think it's just me because this dashboard works when I mine your DGB scrypt pool.  And I can have a tab for each in same browser.  SHA with zeros and Scrypt with apparently accurate figures.
 
Would greatly appreciate it.

The Blockfactory DGB SHA-256 Mining Pool

Any update on this issue Lucazane?

[STeaks]

If someone could please help me out a bit, maybe you have experienced this before or if you could point me in the right direction. I have already tried searching for this on google but have not found anything related.
I have a GTX 1070 mining with ccminer, Skein algorithm. I just installed the card last night and on first boot was getting about 400MHs, I restarted my pc for windows update and right after the update my mining rate went down to 130MHs. I did fresh install of operating system to undo any updates but the card still only gives out 130MHs.
I also tried installing two different driver versions but it did not work, gave same Hashrate.

I am also running a GTX 1080 on a separate rig and that one is getting me 500MHs, using the same algorithm(skein) on the blocks factory with ccminer.

I don't understand why the GTX 1070 MHs dropped to 130 from 400 with all the mining settings staying the same.

Could it be that the graphics card is broken?

 I appreciate any help I can get.

[lucazane]

Say Lucazane -

I was wondering if we could get the Average Hashrate figures fixed on your DGB SHA-256 pool.  Hard to figure out exactly what our average hash rate is.  Been mining there for a week and given the profitability of DGB looks like I'll be sticking around a while.  As will others.

I don't think it's just me because this dashboard works when I mine your DGB scrypt pool.  And I can have a tab for each in same browser.  SHA with zeros and Scrypt with apparently accurate figures.
  
Would greatly appreciate it.

The Blockfactory DGB SHA-256 Mining Pool

Any update on this issue Lucazane?

Should work now, but If you see an issue, please alert me.

Edit : it will take 12 hours before having correct values.

[usernamehere]

I noticed that my invalid hashrate on the pool is pretty high and as much as 10% but hovers around 5%.  So I decided that I would investigate since my invalids on other pools is well under 1%. I found that my ping is 160ms and have come to conclude that this is probably what's causing my high invalid hashrate. Any future plans to get the pool on a faster connection?

[Swimmer63]

What are you mining with and what alto are you mining.
I found this to be the only pool I have to set the mining difficulty on for each of my ASIC miners. Only then do I get a low reject rate.

[usernamehere]

sha256 pool and with a Antminer S9.  The pool wants to auto set my diff to 16k and I haven't tried to adjust it.

[usernamehere]

The pool assigns the diff 16.4k to my miner and really I should be closer to 9.3k according to CK's post https://bitcointalk.org/index.php?topic=274023.0 I should be closer to 9.3k. Now let's see if this has a positive effect or not.

[lucazane]

I noticed that my invalid hashrate on the pool is pretty high and as much as 10% but hovers around 5%.  So I decided that I would investigate since my invalids on other pools is well under 1%. I found that my ping is 160ms and have come to conclude that this is probably what's causing my high invalid hashrate. Any future plans to get the pool on a faster connection?

Digibyte is a realy fast coin : 15 sec blocktime.
So invalid share a more frequent than bitcoin or other slower coin.

You can adjust your difficulty manualy by adding _diffxxxx in your miner name.
Ex : Miner.worker_diff9300

[Swimmer63]

I am using S9's also. Even though the pool sets the difficulty to 16K automatically, I get a lower invalid rate if I manually enter "_diff16384" after my worker name as OP describes. Don't ask me why but the hash rate is much more stable and productive when I do this for each worker.