[Antminer S1 Sales open] Price changes daily, now 0.414 BTC for 180GH/s

[solitude]

What are your HW rate and power supply. All Ant's are not created equal I have some that don't like 400. 375 is always stable and gives 190 GH with usually 0 HW.

HW rate?  Where do i find this?  Power Supply is Corsair RM850

[Gamer67]

post a screen shot of your miner status page

[solitude]

What are your HW rate and power supply. All Ant's are not created equal I have some that don't like 400. 375 is always stable and gives 190 GH with usually 0 HW.

I have two Antminer's and both are maxing out at 190 GH with a 400 mhz overclock.  Am I just really unlucky?

[smooth]

I thought 200GH was guaranteed if you overclocked to 400 mhz?

Guaranteed? Overclocking is not guaranteed at all.

[Gamer67]

Each is different. I have some that only like 393, others will do 400 and even 406.

This is with me keeping the HW errors to a max of 0.99% (none hit that but that is my limit) I did take a few to 412 but the hw errors were just over 1%

[Unacceptable]

What are your HW rate and power supply. All Ant's are not created equal I have some that don't like 400. 375 is always stable and gives 190 GH with usually 0 HW.

HW rate?  Where do i find this?  Power Supply is Corsair RM850

I hate that PSU..........only 3 PCIE cables,WTF  

I got one & it should power 2 Ants,I was going use a cable I had Cablez make to pull power from the ESP,but I'm not,better safe than sorry  

Picked up one these :

http://www.ultraproducts.com/applications/campaigns/campaigntemplate.asp?CampaignID=1111

Very happy with it,it has 6 PCIExpress cables,3 6pin & 3 8pin individual cables (1 connector each,no doubles) & its 60 amp,single rail  

2 Ants are running about 800 watts,NO OC,so far not a whimper  

[MrTeal]

post a screen shot of your miner status page

Once again, both are overclocked to 400mhz

Antminer 2 has 10% HW errors, and Antminer 1 has almost 10%. That's likely the source of your problems.

[solitude]

Antminer 2 has 10% HW errors, and Antminer 1 has almost 10%. That's likely the source of your problems.

Is that a problem with the power supply or the antminer?

[Gamer67]

Drop it down to 393.

393.75 MHz    '5F05'

You might even need to go lower.

387.5   MHz    '5E85'

[bitcoin_miner]

when store open? I'll buy it

[Gamer67]

Drop it down to 393.

393.75 MHz    '5F05'

You might even need to go lower.

387.5   MHz    '5E85'

Where are you seeing 10% HW errors?  What # on that status page tells me this?

HW / (HW + DiffA + DiffR + DiffS)= xx  *100


Simple rule: Keep the HW lower than accepted shares and you will be ok.

[solitude]

Drop it down to 393.

393.75 MHz    '5F05'

You might even need to go lower.

387.5   MHz    '5E85'

Where are you seeing 10% HW errors?  What # on that status page tells me this?

HW / (HW + DiffA + DiffR + DiffS)= xx  *100


Simple rule: Keep the HW lower than accepted shares and you will be ok.

Can I tweak the timeout to increase GH?   Thanks for your help btw! 

[bitcoin_miner]

For Bitmain, I need info from you.
Is 112bit.com authorized distributor for USA by Bitmain Tech Ltd  ? caused at this site, wrote "authorized distributor for USA by Bitmain Tech Ltd ".
waiting your info

[Gamer67]

Drop it down to 393.

393.75 MHz    '5F05'

You might even need to go lower.

387.5   MHz    '5E85'

Where are you seeing 10% HW errors?  What # on that status page tells me this?

HW / (HW + DiffA + DiffR + DiffS)= xx  *100


Simple rule: Keep the HW lower than accepted shares and you will be ok.

Can I tweak the timeout to increase GH?   Thanks for your help btw! 

I am not sure as I have not done any comparisons myself or read about any others. I just keep mine at 35 or 36 depending on the clock speed.

[chopsticks]

What is the opinion of the group on the HW errors?

[solitude]

For those of you that use their Ants wirelessly, I have a question:

if I connect a 5Dbi antenna and put my Ant downstairs one floor beneath the router, directly underneath the router, I should be able to get a good signal right?

[klondike_bar]

Drop it down to 393.

393.75 MHz    '5F05'

You might even need to go lower.

387.5   MHz    '5E85'

Where are you seeing 10% HW errors?  What # on that status page tells me this?

HW / (HW + DiffA + DiffR + DiffS)= xx  *100


Simple rule: Keep the HW lower than accepted shares and you will be ok.

Can I tweak the timeout to increase GH?   Thanks for your help btw! 

your issue is that at 400Mhz the antminer is being overworked - either the power supply is not quite powerful enough to feed it or the PCB power connections just cant handle being so far out of spec.

Try 387.5 - it works on ~80% of machines and produces about 194GH. Considering you are losing almost 20GH to hardware errors, it makes sense to tune it down a little

[solitude]

Is there anyone who successfully connected their Antminer to their wireless network that can help me set this up?  I've already changed both of my miners to a different IP address, but the wireless one isn't bringing up the setup page when I put in the address...

[solitude]

Is there anyone who successfully connected their Antminer to their wireless network that can help me set this up?  I've already changed both of my miners to a different IP address, but the wireless one isn't bringing up the setup page when I put in the address...

How do I get my router to accept the Antminer as a legitmate wireless connection?

[chopsticks]

Changed mine from 400 freq down to 393.75 and it has a lot less HW errrors!

HW errors less than the amount of Accepted shares now.