[ANN] The First Litecoin PPS Pool (litecoinpool.org)

[pooler]

well that number is up in the 1ks not good. But i think i narrowed it down to my battery backup. Either that or i fried a card already.. that would be the far right card. If i reboot the computer its fine but my battery backup is overloading from the computer pulling over the rated wattage. I dont know because even me erupters are having a high number of rejects as of here lately and i got only 4 of them pluged into the computer with a fan right on top of them. This is all of a sudden. any ideas?

The R figure isn't significant in itself, it's the R/A ratio that is important; anything below 1% should be fine for GPU mining, given that some of the software latency introduced by cgminer can't be avoided, and results in additional stale shares. Assuming those rejects are stales, if you are getting more than 1% then you should try lowering the intensity a bit.

[demonmaestro]

Well i got a bigger back up and while ive been gone ive notice its dropped back down to 300ish kh and i dont know the status of the other cards as of currently. So in a few hours i will be able to see whats going on. and get the bigger battery on it.

[demonmaestro]

It appears that the battery back up was the issue. hashing away at an average of 1.1mh.  not bad i guess for 3 7850s

[demonmaestro]

Could someone tell me what the issue is here.
This is what it use to be at


And this is what it is now...

[Beaflag VonRathburg]

^ Where is there an issue?

[demonmaestro]

my hw rate is going up and causing my rejects to go up. yet i have even lowered the intinsity. I dont understand why.

[pooler]

my hw rate is going up and causing my rejects to go up.

That's not how it works. HW errors and rejections are unrelated. The R/A ratio in the picture above is just fine for GPU mining. (Please re-read what I wrote above.)

[demonmaestro]

Okay fine but i dont understand why at first both my R value and my HW value were 0 now they both have value to them. I had notice a drop in the pool from 1200khs to 600kh/s and had seen that my HW and R value had gone up from 0. Just trying to understand why.  I undestand that the software can cause issues from time to time but wouldnt the HW value go back to 0?

[pooler]

I undestand that the software can cause issues from time to time but wouldnt the HW value go back to 0?

Those are counts since cgminer was started, they can't decrease.

[mmitech]

Okay fine but i dont understand why at first both my R value and my HW value were 0 now they both have value to them. I had notice a drop in the pool from 1200khs to 600kh/s and had seen that my HW and R value had gone up from 0. Just trying to understand why.  I undestand that the software can cause issues from time to time but wouldnt the HW value go back to 0?

in your case the best thing to do is to open your Cgminer folder, there is a README file and SCRYPT-README file, you can start slowly from there, you will find allot of answers and explanations .

[pooler]

Can anybody please explain the "Lifetime Rewards History" overview in "My Account / View full history..." on https://www.litecoinpool.org/rewards ?

The "Last 30 Days Summary" table is simply a day-by-day summary for the last 30 days.
The "Lifetime Rewards History" on the other hand, is not calendar-based. It subdivides your rewards by PPS rate (and difficulty), so a new row only appears when the PPS rate changes (so basically when the network difficulty changes). The timestamp displayed in each row is the last time at which you submitted a share for a given PPS rate (that's why the column header says "Last Time"). On average, the PPS rate should change every 3.5 days, and that's why not all dates appear in this table.

[pooler]

Just a quick message to let you know about the recent changes and additions.

• The charts page has been updated to use a newer client-side charting library, which is faster, allows you to zoom and pan, and has better browser compatibility.
• A few statistics have been added to the "My Account" page, such as per-worker 24-hour average hash rates.
• Users now have the choice to hide their username from public statistics.
• The FAQ has been expanded to address a number of common questions.

I'm also happy to announce that the new Stratum implementation has been doing wonders: we now have users with stale rates as low as 0.03%, even on servers handling over 1000 workers!
Even miners from China have stale rates as low as 0.15% on our West-Coast servers, which has pretty much convinced me that setting up additional servers in Asia would be pointless.
(Note: if your stale rates are significantly higher, it is almost certainly due to additional latency generated by your mining software. See the FAQ.)

[beanhead]

Hi,

Are there any issues with auto payouts at the moment?  A couple of times in the last few days it doesn't seem to have worked.  Instant payout works though.

Cheers,

Beanhead

[demonmaestro]

seems to be working fine for me.

[pooler]

Are there any issues with auto payouts at the moment?  A couple of times in the last few days it doesn't seem to have worked.  Instant payout works though.

Everything seems to be working fine here.
Remember that automatic payouts are not instant: once the payout threshold is reached, it may take up to a couple of hours before the actual payment is processed.

[Icon]

Got a question, what good/use is the 2factor used to.. its not used for logging in . cant lock the payout address with it can you?  I know it has a one time lock out payout address option..

Love the pool.

Icon

[pooler]

Got a question, what good/use is the 2factor used to.. its not used for logging in.

Actually, it is. Are you sure you logged out and back in after enabling it?

[Icon]

Well it says its enabled i hit the log out button on the account page then type in my log in info/pw and back to account page, don't even get asked to enter the google authen..

[pooler]

Well it says its enabled i hit the log out button on the account page then type in my log in info/pw and back to account page, don't even get asked to enter the google authen..

I have just made some tests using my account, and I cannot seem to reproduce the issue. If I log out and try to log back in, I always get asked for the one-time code. Are you sure this isn't some strange browser cache issue? What browser are you using? Also, could you please try to log in using a wrong password and tell me what happens in that case?
Anybody else experiencing this?

[Icon]

Well i was installing a fresh copy of windows on another pc, When i tried to log in using firefox with no addons installed and knowing the 2factor was enabled and was never prompted for the google auth one time key, matter fact only time i'm asked for the key is to enable/disable it.

Also i tried on my desktop pc that i game on (using firefox), I loged in and disabled and re enabled it, and loged out and back in still was not prompted for the 2factor key.