|
squashpile
|
 |
May 14, 2014, 05:05:17 PM |
|
I have an extra S2 coupon. I'm looking for an S1 coupon if anyone has one they don't need.
Please PM me
|
SquashPool - 0% Fee - Dedicated P2Pool VPS - Atlanta, GA - SSD - Gig uplink
|
|
|
|
|
|
|
|
|
|
|
|
The network tries to produce one block per 10 minutes. It does this by automatically adjusting how difficult it is to produce blocks.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
jedimstr
|
|
May 14, 2014, 05:08:50 PM |
|
the S1s come and go. but pretty stable.
i have one that likes to hang and go bright solid green led on me - still uncertain what it means but its rare so i dont worry.
the s2 has been solid since i got it going and just as im typing this the fkr comes back to life for about 3 seconds...
up until today i was happy with its stability over anything else.
now its beeping at me again....
its annoying cos if it was the network it would affect them all.
and its just this one.
so far....
Could be an IP collision on your LAN. Do you have a mix of DHCP and static IP's used for your miners? If one of your miners or another device on your network takes an IP that you are using as a static IP for your S2, and connectivity is reset or you rebooted the miner, then it would probably exhibit the behavior you're describing. |
|
|
|
|
wpgdeez
|
|
May 14, 2014, 05:16:53 PM |
|
the S1s come and go. but pretty stable.
i have one that likes to hang and go bright solid green led on me - still uncertain what it means but its rare so i dont worry.
the s2 has been solid since i got it going and just as im typing this the fkr comes back to life for about 3 seconds...
up until today i was happy with its stability over anything else.
now its beeping at me again....
its annoying cos if it was the network it would affect them all.
and its just this one.
so far....
Could be an IP collision on your LAN. Do you have a mix of DHCP and static IP's used for your miners? If one of your miners or another device on your network takes an IP that you are using as a static IP for your S2, and connectivity is reset or you rebooted the miner, then it would probably exhibit the behavior you're describing. My wifes iphone was doing this, pain in the ass to narrow down the device  |
|
|
|
|
|
kendog77
|
|
May 14, 2014, 05:20:52 PM |
|
the S1s come and go. but pretty stable.
i have one that likes to hang and go bright solid green led on me - still uncertain what it means but its rare so i dont worry.
the s2 has been solid since i got it going and just as im typing this the fkr comes back to life for about 3 seconds...
up until today i was happy with its stability over anything else.
now its beeping at me again....
its annoying cos if it was the network it would affect them all.
and its just this one.
so far....
Could be an IP collision on your LAN. Do you have a mix of DHCP and static IP's used for your miners? If one of your miners or another device on your network takes an IP that you are using as a static IP for your S2, and connectivity is reset or you rebooted the miner, then it would probably exhibit the behavior you're describing. My wifes iphone was doing this, pain in the ass to narrow down the device I had this problem with a static ip S1 and a DHCP printer, and it took me a while to figure out why I had intermittent connectivity. I fixed the issue by specifying a DHCP IP range in my router that did not conflict with any static IP addresses that I assigned to my Antminers. |
|
|
|
|
|
TracerX
|
|
May 14, 2014, 05:27:27 PM |
|
I had this problem with a static ip S1 and a DHCP printer, and it took me a while to figure out why I had intermittent connectivity. I fixed the issue by specifying a DHCP IP range in my router that did not conflict with any static IP addresses that I assigned to my Antminers.
And that's how you safely run both DHCP and a statics on the same subnet. Set the DHCP to only draw from a specific range (say 192.168.1.150-192.168.1.200) and then assign all your mining gear IP addresses outside that range (192.168.1.100, 101, 102, 103, etc) to keep things straight. |
|
|
|
|
|
jedimstr
|
|
May 14, 2014, 05:29:07 PM |
|
the S1s come and go. but pretty stable.
i have one that likes to hang and go bright solid green led on me - still uncertain what it means but its rare so i dont worry.
the s2 has been solid since i got it going and just as im typing this the fkr comes back to life for about 3 seconds...
up until today i was happy with its stability over anything else.
now its beeping at me again....
its annoying cos if it was the network it would affect them all.
and its just this one.
so far....
Could be an IP collision on your LAN. Do you have a mix of DHCP and static IP's used for your miners? If one of your miners or another device on your network takes an IP that you are using as a static IP for your S2, and connectivity is reset or you rebooted the miner, then it would probably exhibit the behavior you're describing. My wifes iphone was doing this, pain in the ass to narrow down the device I had this problem with a static ip S1 and a DHCP printer, and it took me a while to figure out why I had intermittent connectivity. I fixed the issue by specifying a DHCP IP range in my router that did not conflict with any static IP addresses that I assigned to my Antminers. Yeah, I do the same. I have a specific dedicated IP range for all my Miners, another one for network equipment with static IPs (managed switches, temp sensors, etc) and another range for all my Dynamic stuff. I try to specify Static IP's where I can though to make things more manageable. |
|
|
|
Biodom
Legendary
 Offline
Activity: 3752
Merit: 3853
|
|
May 14, 2014, 09:49:22 PM |
|
hate to say it but i have 1 crippled S1 that took out a cougar 700w psu.
i can get into it, i can reboot it a billion times - the best i get is a brief flash on the board and thats that.
silver lining, everything else has come back online in unison.
how longs the warranty on these rigs?
this was bought as a pair on the 13th of March - arrived on the 17th so its not even 2 months...
E2A - i walk 8 feet away, sit by the pool and cool my feet... it only comes back online,,, i can see it twinkling away over there..ffs.
dem ants, eh
I have one unit that was doing it (intense momentary flashing and no hashing). I figured the cause-the panel near top left (close to ethernet connection) was overheating because of: 1. Slow fans on this machine 2. grey ribbons that were not properly folded and were blocking the airflow In your case perhaps increasing air temp contributed My solution: i directed the airflow from an additional external fan (I used Vornado, but any one can do) toward the panel. After a few seconds of increased air flow, hashing resumed uninterrepted and continued OK since. Somebody later posted that there is a temperature sensor that shuts everything down when that sensor reaches high temps (145oC). This is not the sensor that shows temp of the board on the web interface because that sensor was at OK reading in my case. Check it out with a fan. |
|
|
|
|
|
faetos
|
|
May 14, 2014, 11:53:36 PM |
|
I saw we can donate S2 coupons, so if anyone wants mine let me know via PM. I have 1 400USD coupon expires May 23rd and 3 that expire on May 30th.
|
|
|
|
|
|
nottm28
|
|
May 15, 2014, 12:09:36 AM |
|
hate to say it but i have 1 crippled S1 that took out a cougar 700w psu.
i can get into it, i can reboot it a billion times - the best i get is a brief flash on the board and thats that.
silver lining, everything else has come back online in unison.
how longs the warranty on these rigs?
this was bought as a pair on the 13th of March - arrived on the 17th so its not even 2 months...
E2A - i walk 8 feet away, sit by the pool and cool my feet... it only comes back online,,, i can see it twinkling away over there..ffs.
dem ants, eh
I have one unit that was doing it (intense momentary flashing and no hashing). I figured the cause-the panel near top left (close to ethernet connection) was overheating because of: 1. Slow fans on this machine 2. grey ribbons that were not properly folded and were blocking the airflow In your case perhaps increasing air temp contributed My solution: i directed the airflow from an additional external fan (I used Vornado, but any one can do) toward the panel. After a few seconds of increased air flow, hashing resumed uninterrepted and continued OK since. Somebody later posted that there is a temperature sensor that shuts everything down when that sensor reaches high temps (145oC). This is not the sensor that shows temp of the board on the web interface because that sensor was at OK reading in my case. Check it out with a fan. In my experience, 99/100 if a miner wont hash then it's due to some kind of network issue. Power off router, wait 30, power off miner wait 30, wait another 3 minutes for cron task to kick in. Works again. |
donations not accepted
|
|
|
philipma1957
Legendary
Offline
Activity: 4116
Merit: 7824
'The right to privacy matters'
|
|
May 15, 2014, 03:53:40 AM |
|
I have some s2 coupons. 2 of them.
Also if any one has an s1 I would like 1 coupon.
philipma1957 is the bitmain name.
I got 1 s1 coupon and I traded off 1 s2.
So I have 1 s2 left .
|
|
|
|
miniMiner
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 15, 2014, 04:35:29 AM
Last edit: May 15, 2014, 05:33:56 AM by miniMiner |
|
Hi everyone, I am looking for some s2 coupons. I am miniMiner on bitmaintech. I am doubling down and I am going to invest in some heavy metal as it were.
I have one s1 coupon for those guys that were looking for them.
UPDATE: I am good for now, thanks everyone!!!!
If any of you that sent me a coupon want the s1 coupon I have, let me know. After 24 hours I wull give the s1 coupon away.
Posted from Bitcointa.lk - #Qgda9l6DQOotg2XH
|
|
|
|
|
taipo
Full Member
Offline
Activity: 238
Merit: 100
Kia ora!
|
|
May 15, 2014, 04:45:01 AM |
|
Sent you one miniMiner
id: taipo
|
|
|
|
miniMiner
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 15, 2014, 05:13:38 AM |
|
Faetos!!! Thank you!!!!!
Taipo!!! Thank you!!!!!
I received your coupons and they will help out. I am wanting to make a mad dash for miners as the difficulty climbs. Crazy, I know!!! I am hoping to grab about 5 of these babies within the next month.
Posted from Bitcointa.lk - #SZjyjsdjyBgQtqFC
|
|
|
|
|
miniMiner
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 15, 2014, 05:19:44 AM |
|
By the way, bitcointalk.org is limiting my messages, so that is why it took me so long to respond via PM. I posted trust feedback for you already Faetos and I will post for you too Taipo as soon as they let me.
Posted from Bitcointa.lk - #adsS9DeIVtTQnA9o
|
|
|
|
|
taipo
Full Member
Offline
Activity: 238
Merit: 100
Kia ora!
|
|
May 15, 2014, 05:28:20 AM |
|
No prob, good luck with your venture.
If you know of anyone that has a spare S1 coupon, I am after one thanks
id: taipo
|
|
|
|
miniMiner
Newbie
Offline
Activity: 4
Merit: 0
|
|
May 15, 2014, 05:33:58 AM |
|
No prob, good luck with your venture.
If you know of anyone that has a spare S1 coupon, I am after one thanks
id: taipo SENT!!! Posted from Bitcointa.lk - #ZyiEnyKBEH5hY2S4 |
|
|
|
|
taipo
Full Member
Offline
Activity: 238
Merit: 100
Kia ora!
|
|
May 15, 2014, 05:37:21 AM |
|
Thanks, good trade.  |
|
|
|
|
tzortz
|
|
May 15, 2014, 07:56:41 AM |
|
I am sure "donation style" coupons will boost Bitmain's sales even higher.
|
All is Mine!
1H7LUdfx9AFTMSXPsCBror3RDk57zgnc2R
|
|
|
alexrossi
Legendary
Offline
Activity: 3724
Merit: 1739
Join the world-leading crypto sportsbook NOW!
|
|
May 15, 2014, 08:16:20 AM |
|
I have 2x AntMiner S1 Coupon 0.05 BTC and 2x AntMiner S2 Coupon 400 USD, someone is interested?
|
|
|
|
nikolaz
Member
Offline
Activity: 98
Merit: 10
|
|
May 15, 2014, 09:39:12 AM |
|
I have 2x AntMiner S1 Coupon 0.05 BTC and 2x AntMiner S2 Coupon 400 USD, someone is interested?
Alright... I have 14 S1 and 12 S2 coupons... PM me your receiver ID - maximum 2 coupon per user as I would like to share with as many people as possible. Cheers |
|
|
|
|
|
