[Minera v0.9.1] Your next mining dashboard - Antminer/CPUminer/CGminer/BFGminer

[GrrOucH]

I have noticed on my rpi2 that when Minera boots there seems to be a problem with Postfix. Get multipul Postmulti warnings about unused parameter: inet_protocol=ipv4 ant there a bunch of entries about ipv6 as well. shows the problem to be in /etc/postfix/main.cf  . Not sure what that's about .

[michelem]

I have noticed on my rpi2 that when Minera boots there seems to be a problem with Postfix. Get multipul Postmulti warnings about unused parameter: inet_protocol=ipv4 ant there a bunch of entries about ipv6 as well. shows the problem to be in /etc/postfix/main.cf  . Not sure what that's about .

you don't need Postfix, if you can paste the exact line outputs I can tell you something, otherwise just skip it.

@dukester99 I don't know what's your problem with donation pool, my suggest is to start from the latest image build (http://getminera.com/download/latest), because I don't know anything about your installation and it's hard for me troubleshooting it.

[cavaliersrus]

hey mich question since i updated to latest version at this time when i run autotune it will not save the freq of my gridseed 5chip miners its been runing for over 5.5 hours as of 10:52 am CST... no values have changed in over a hour from watching debug on the log area on the website

[michelem]

hey mich question since i updated to latest version at this time when i run autotune it will not save the freq of my gridseed 5chip miners its been runing for over 5.5 hours as of 10:52 am CST... no values have changed in over a hour from watching debug on the log area on the website

Can you give more info? Are you using CPUminer? Did you enable autotune? What was the start freq you set up?

[cavaliersrus]

hey mich question since i updated to latest version at this time when i run autotune it will not save the freq of my gridseed 5chip miners its been runing for over 5.5 hours as of 10:52 am CST... no values have changed in over a hour from watching debug on the log area on the website

Can you give more info? Are you using CPUminer? Did you enable autotune? What was the start freq you set up?

yes using cpuminer and enabled autotune and debug mode started at 950 mhz and it underclocked 3 of my miners chips to below 9:50 most likely due to heat sink issues with gridseed im awaiting thermal paste ... its got one of my seeds at almost 1,000 mhz which is ok cause i volt modded the seed

[cavaliersrus]

i was able to go back threw the logs from last to beginning and was able to get  the following

0@0 950MHz
0@1 950MHz
0@2 925MHz
0@3 950MHz
0@4 925MHz

1@0 925MHz
1@1 950MHz
1@2 950MHz
1@3 925MHz
1@4 950MHz

2@0 950MHz
2@1 925MHz
2@2 950MHz
2@3 950MHz
2@4 950MHz

3@0 1000MHz
3@1 975MHz
3@2 975MHz
3@3 1000MHz
3@4 975MHz


none of them were formed like this like from beginning of the log file

[2015-03-05 06:25:14.4063] 1@1 975MHz: Got nonce 336a161b, Hash <= Htarget! (0x4afefc90) 82.6 KH/s
[2015-03-05 06:25:14.4145] 1@1: ~2053 steps until frequency adjusts to 1000MHz
[2015-03-05 06:25:14.4259] 1: Resetting GC3355 chips
[2015-03-05 06:25:14.5349] 1: Dispatching new work to GC3355 cores (0x4afefc90)


they are all formed like this now so im guessing the autotune feature is done

[2015-03-05 11:20:38.7702] 2@1 925MHz: Got nonce 3340cd98, Hash <= Htarget! (0x905b1aa7) 78.3 KH/s
[2015-03-05 11:20:39.9519] Stratum difficulty set to 418.341
[2015-03-05 11:20:39.9551] Stratum difficulty changed
[2015-03-05 11:20:39.9570] Diff: 418 Work_id: 90679a03
[2015-03-05 11:20:39.9625] Stratum detected new block
[2015-03-05 11:20:39.9644] New Job_id: 232364256555399931783015774965111043699 Diff: 418 Work_id: 9067b702
[2015-03-05 11:20:39.9667] Accepted 3340cd98 GSD 2@1
[2015-03-05 11:20:39.9729] 3: Resetting GC3355 chips
[2015-03-05 11:20:39.9748] 2: Resetting GC3355 chips
[2015-03-05 11:20:40.0129] 1: Resetting GC3355 chips
[2015-03-05 11:20:40.0229] 0: Resetting GC3355 chips
[2015-03-05 11:20:40.0775] 3: Dispatching new work to GC3355 cores (0x9067b702)
[2015-03-05 11:20:40.0796] 2: Dispatching new work to GC3355 cores (0x9067b702)
[2015-03-05 11:20:40.1160] 1: Dispatching new work to GC3355 cores (0x9067b702)
[2015-03-05 11:20:40.1260] 0: Dispatching new work to GC3355 cores (0x9067b702)

[michelem]

i was able to go back threw the logs from last to beginning and was able to get  the following

0@0 950MHz
0@1 950MHz
0@2 925MHz
0@3 950MHz
0@4 925MHz

1@0 925MHz
1@1 950MHz
1@2 950MHz
1@3 925MHz
1@4 950MHz

2@0 950MHz
2@1 925MHz
2@2 950MHz
2@3 950MHz
2@4 950MHz

3@0 1000MHz
3@1 975MHz
3@2 975MHz
3@3 1000MHz
3@4 975MHz


none of them were formed like this like from beginning of the log file

[2015-03-05 06:25:14.4063] 1@1 975MHz: Got nonce 336a161b, Hash <= Htarget! (0x4afefc90) 82.6 KH/s
[2015-03-05 06:25:14.4145] 1@1: ~2053 steps until frequency adjusts to 1000MHz
[2015-03-05 06:25:14.4259] 1: Resetting GC3355 chips
[2015-03-05 06:25:14.5349] 1: Dispatching new work to GC3355 cores (0x4afefc90)


they are all formed like this now so im guessing the autotune feature is done

[2015-03-05 11:20:38.7702] 2@1 925MHz: Got nonce 3340cd98, Hash <= Htarget! (0x905b1aa7) 78.3 KH/s
[2015-03-05 11:20:39.9519] Stratum difficulty set to 418.341
[2015-03-05 11:20:39.9551] Stratum difficulty changed
[2015-03-05 11:20:39.9570] Diff: 418 Work_id: 90679a03
[2015-03-05 11:20:39.9625] Stratum detected new block
[2015-03-05 11:20:39.9644] New Job_id: 232364256555399931783015774965111043699 Diff: 418 Work_id: 9067b702
[2015-03-05 11:20:39.9667] Accepted 3340cd98 GSD 2@1
[2015-03-05 11:20:39.9729] 3: Resetting GC3355 chips
[2015-03-05 11:20:39.9748] 2: Resetting GC3355 chips
[2015-03-05 11:20:40.0129] 1: Resetting GC3355 chips
[2015-03-05 11:20:40.0229] 0: Resetting GC3355 chips
[2015-03-05 11:20:40.0775] 3: Dispatching new work to GC3355 cores (0x9067b702)
[2015-03-05 11:20:40.0796] 2: Dispatching new work to GC3355 cores (0x9067b702)
[2015-03-05 11:20:40.1160] 1: Dispatching new work to GC3355 cores (0x9067b702)
[2015-03-05 11:20:40.1260] 0: Dispatching new work to GC3355 cores (0x9067b702)

So, autotune works, what's wrong?

[cavaliersrus]

it does not autosave the freq of them i tried shutting down and restart and diddnt save them still had old freq's so i have to edit them to the new ones from the log file

[Visvas]

totally new to Minera, but really likes the concept so far:) which logs should i look into for trying to figure out why the miner stops sometimes?

Using Cgminer with two antminer u3s. Pi 2. latest Minera.

Minera seems to handle reset/restart of the miner sometimes, but not always.

Thanks!

[magaman]

Can anyone point me towards an absolute 110% complete idiots guide to setting up wifi on my Minera image?

[michelem]

Can anyone point me towards an absolute 110% complete idiots guide to setting up wifi on my Minera image?

Check this https://github.com/michelem09/minera/wiki/Configure-Wifi

@visvas check your cgminer log, you can find it in the bottom of the dashboard. For "stop" what do you mean?

[ammi84]

Can anyone point me towards an absolute 110% complete idiots guide to setting up wifi on my Minera image?

Check this https://github.com/michelem09/minera/wiki/Configure-Wifi

@visvas check your cgminer log, you can find it in the bottom of the dashboard. For "stop" what do you mean?

thank you for that guide
i made a little workaround with vnc-server and the gui setup for wifi ^^
works too but your guide looks much more easy

[cavaliersrus]

i see a new update mich just tried to update it threw minera and its not updating yet just rebooted and trying again to update...


just updated cant wait to see the upgrades

[Visvas]

Can anyone point me towards an absolute 110% complete idiots guide to setting up wifi on my Minera image?

Check this https://github.com/michelem09/minera/wiki/Configure-Wifi

@visvas check your cgminer log, you can find it in the bottom of the dashboard. For "stop" what do you mean?

Log seems to only be from the last time that cgminer started. It restarted about 26mins ago now, no interaction from me or otherwise.
Thats what i mean by stop. minera seems to have been running fine, but for some reason the miner had to be restarted. Its that i would like to have a look at in a log somewhere..

[Blackross]

Did you get rid of screen?

it updated yesterday and now when I ssh in I can't type screen -r and get the miner... With neither of the of the miners (bfg, cg, etc), they run ok though.

WAIT, think I know what I'm doing wrong, I'll check it when I get back home today.

[michelem]

Did you get rid of screen?

it updated yesterday and now when I ssh in I can't type screen -r and get the miner... With neither of the of the miners (bfg, cg, etc)

What's the output of "screen -r"?

If you run this what's the output?

Code:

ps aux|grep screen

[Blackross]

Well with screen -r it just says no screen to attach to.... at work now it won't be till 5.30 today till I get home.

[Blackross]

The only thing I use screen for is to disable pools I don't want to mine on and to adjust the rotation times, but keep them in the list. since I can't do that with the Web interface (hint for a added feature, lol)

[michelem]

The only thing I use screen for is to disable pools I don't want to mine on and to adjust the rotation times, but keep them in the list. since I can't do that with the Web interface (hint for a added feature, lol)

If there isn't any screen active I suppose there isn't any active miner, that's the problem. Check logs.

[Blackross]

No its mining.... I see stats on the pools I use.  and I see the 360 minutes rotation.  But I think I need to sudo screen -r