Bitcoin Forum
June 22, 2024, 01:44:33 PM *
News: Voting for pizza day contest
 
   Home   Help Search Login Register More  
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 [29] 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 »
  Print  
Author Topic: ROCKMINER ASIC miner official thread  (Read 199432 times)
bobsag3
Hero Member
*****
Offline Offline

Activity: 546
Merit: 500

Owner, Minersource.net


View Profile
July 12, 2014, 03:57:20 PM
 #561

I have a problem connecting more than 2 Rocket Boxen on the raspberry Pi.

When i connect more (4 Boxen) with a good d-link hub between, 16 board are detected and shown, but they are only working with about 70 GH/s.

When i connect the same to a windows pc and using cgminer everything is fine!

The Pi Image does not support more than 2 miners/pi
Billbags
Sr. Member
****
Offline Offline

Activity: 280
Merit: 250

Brainwashed this way


View Profile
July 12, 2014, 05:49:16 PM
 #562

Any aftermarket fan recommendations for the RK-Box miners?
This thing is LOUD and is beginning to bother my tinnitus  Undecided

Thanks!

[/quote: I installed a manual fan control on my RK-Boxes that is working well to dramatically reduce the fan noise and still keep the blades cool. Highly reccomended if the Rocket Boxes are in your house. I just lowered fan speed and monitored during the hotest times of the day to get right setting for quiet cooling. I have not had to adjust fan speed since installed and adjusted.     Here is the link of the ones I'm using:
 http://www.amazon.com/gp/aw/d/B004LL8KF6?cache=8dd22ea26140667f1737f48c0bd46cbe&pi=SX200_QL40&qid=1404945076&sr=8-1#ref=mp_s_a_1_1

Note: plastic guide on the end of the fan controller wires must be shaved down to fit on the miner. I used a knife, takes about 5 seconds, works well

Also, I just got confirmation from Rockminer that the firmware update for the r3 will also work for rk-Box. Doggie has complete firmware update instructions on his r3 setup page.


Update:  Firmware upgrade instructions for r3 does work with rk-Box with pi. On my two units(each has a pi) I had to ssh with pi then exit, then ssh a second time to allow for update. The first time you ssh to pi a corrupted dadabase error comes up, but once you fully exit and go back in everything works fine and update is applied. You can now adjust freq's at bottom of pools page.

Listen: meat beat manifesto ~ Edge of no control (pt.1)
Read:"He who controls the past controls the future. He who controls the present controls the past." ~ George Orwell
Think: http://unenumerated.blogspot.com/2014/12/the-dawn-of-trustworthy-computing.html
CanaryInTheMine
Donator
Legendary
*
Offline Offline

Activity: 2352
Merit: 1060


between a rock and a block!


View Profile
July 12, 2014, 06:03:02 PM
 #563

So the cat is now out of the bag then...
R4 is next release Smiley
mstrongbow
Sr. Member
****
Offline Offline

Activity: 322
Merit: 250

3D Printed!


View Profile
July 12, 2014, 06:13:10 PM
 #564

I will post up with pics later  Grin

Any aftermarket fan recommendations for the RK-Box miners?
This thing is LOUD and is beginning to bother my tinnitus  Undecided

Thanks!

[/quote: I installed a manual fan control on my RK-Boxes that is working well to dramatically reduce the fan noise and still keep the blades cool. Highly reccomended if the Rocket Boxes are in your house. I just lowered fan speed and monitored during the hotest times of the day to get right setting for quiet cooling. I have not had to adjust fan speed since installed and adjusted.     Here is the link of the ones I'm using:
 http://www.amazon.com/gp/aw/d/B004LL8KF6?cache=8dd22ea26140667f1737f48c0bd46cbe&pi=SX200_QL40&qid=1404945076&sr=8-1#ref=mp_s_a_1_1

Note: plastic guide on the end of the fan controller wires must be shaved down to fit on the miner. I used a knife, takes about 5 seconds, works well

Also, I just got confirmation from Rockminer that the firmware update for the r3 will also work for rk-Box. Doggie has complete firmware update instructions on his r3 setup page.


Update:  Firmware upgrade instructions for r3 does work with rk-Box with pi. On my two units(each has a pi) I had to ssh with pi then exit, then ssh a second time to allow for update. The first time you ssh to pi a corrupted dadabase error comes up, but once you fully exit and go back in everything works fine and update is applied. You can now adjust freq's at bottom of pools page.

    Bitcoin-Scratchticket.com       Win Bitcoin Playing Scratchtickets        Provably Fair   
*Got LootCrate?*
*My Stuff For Sale thread/s*   www.CryptoCause.org   Ask me about SEGMining Hosting!
"Don't undertake a project unless it is manifestly important and nearly impossible" - Edwin Land
Trends
Member
**
Offline Offline

Activity: 119
Merit: 10


View Profile
July 12, 2014, 06:44:00 PM
 #565

So the cat is now out of the bag then...
R4 is next release Smiley


2 x R3 in a box.

Quadriga CX BTC/CAD Coin Exchange     www.quadrigacx.com/?ref=umvq5t3i2r6im243v94vucbo
Billbags
Sr. Member
****
Offline Offline

Activity: 280
Merit: 250

Brainwashed this way


View Profile
July 12, 2014, 07:35:50 PM
Last edit: July 13, 2014, 05:03:33 AM by Billbags
 #566

I have adjusted the rk-boxes freq's to 320 and rejects have went from 10.95% to 4.68%. I have lost a small amount of ghs but pool side is 470+/- ghs stable(Slush's Pool). The chips are runnings cooler so I have been able to turn the fan down even more. It has also decreased watts a small amount from wall. Everything seems stable for the last 2 hours since my ghs leveled out at pool. Thanks for eveyones help, time to move to the next project.

Update: Now pool side is 480+/- ghs stable(Slush's Pool). Same low rejects of 3.75% - 4.79%. Both units really hashing good now. Temps with lower fan speed 41-53 depending on time of day.

Listen: meat beat manifesto ~ Edge of no control (pt.1)
Read:"He who controls the past controls the future. He who controls the present controls the past." ~ George Orwell
Think: http://unenumerated.blogspot.com/2014/12/the-dawn-of-trustworthy-computing.html
sushi
Full Member
***
Offline Offline

Activity: 238
Merit: 100

ASIC Myth Buster


View Profile
July 12, 2014, 08:08:14 PM
 #567

Looks like RockMiner released new Firmware.  You can control the frequency via the built-in Web GUI

http://sourceforge.net/projects/rockminer/files/RaspberryPi_Rockminer_Rocket_V1.3.0_192.168.1.254.zip/download


>>> PM me for New ASIC Miner's Info.  We will go check it out <<<
FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P
mstrongbow
Sr. Member
****
Offline Offline

Activity: 322
Merit: 250

3D Printed!


View Profile
July 12, 2014, 08:23:32 PM
 #568

Nice! Just waiting on a replacement R-Pi unit but I will be changing driver to the Zadig driver and playing with CGMiner as BFGMiner does't play well currently. Not only am I getting only 70-80 Gh/s per blade but now only 3/4 blades are hashing  Undecided

    Bitcoin-Scratchticket.com       Win Bitcoin Playing Scratchtickets        Provably Fair   
*Got LootCrate?*
*My Stuff For Sale thread/s*   www.CryptoCause.org   Ask me about SEGMining Hosting!
"Don't undertake a project unless it is manifestly important and nearly impossible" - Edwin Land
sushi
Full Member
***
Offline Offline

Activity: 238
Merit: 100

ASIC Myth Buster


View Profile
July 12, 2014, 08:44:46 PM
 #569

Playing with my Rocket Box and R3,  you might want to use Cgminer on Rocket gears.

If it is hashing low, try to make sure the little control card attached to each hashing PCB seated well and connected well.  

Then check each USB cables connected okay.

Or test just 1 hashing PCB at a time and see if it goes up to 120-130gh/s range.  At least it should hit 110/gh

For some reasons, if it stuck at 32-40GH/S range, unplug the USB and then plug it back in.  If the cgminer doesn't start hashing, restart it and it should be picking up the speed to where it should be.

If you are connecting your Rocket Box or R3 to the home internet router or the office router, and for some reasons, it is hashing so low, please try using the different Internet Connection such as Cellphone Hotspot then to the Wi-Fi bridge to test out if using the different Internet Network Setting would resolve your speed issues. (some half speed hashing could be simply the network issues, but it could be the hardware failures, too but it seems more of the network issues than the Rock Gear hardware side)

Used to S1 and S2, and now getting used to these Rock Box and R3 x2 pack are hashing at over 900GH/S and when I connect 1 Pi to each Rocket Box or R3, it hashes at over 500GH/s





Nice! Just waiting on a replacement R-Pi unit but I will be changing driver to the Zadig driver and playing with CGMiner as BFGMiner does't play well currently. Not only am I getting only 70-80 Gh/s per blade but now only 3/4 blades are hashing  Undecided

>>> PM me for New ASIC Miner's Info.  We will go check it out <<<
FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P
mstrongbow
Sr. Member
****
Offline Offline

Activity: 322
Merit: 250

3D Printed!


View Profile
July 12, 2014, 08:52:15 PM
 #570

Performed a system reboot and scanned for miners again (using MultiMiner/BFGMiner) and it picked up the "missing" blade but within 10 minutes the blade is no longer hashing. I should have time to mess with the drivers and CGMiner soon...working on 3d prints right now

    Bitcoin-Scratchticket.com       Win Bitcoin Playing Scratchtickets        Provably Fair   
*Got LootCrate?*
*My Stuff For Sale thread/s*   www.CryptoCause.org   Ask me about SEGMining Hosting!
"Don't undertake a project unless it is manifestly important and nearly impossible" - Edwin Land
sushi
Full Member
***
Offline Offline

Activity: 238
Merit: 100

ASIC Myth Buster


View Profile
July 12, 2014, 09:05:02 PM
 #571

What kind of USB Hub are you using to connect 4 USB cables?

The bare pcb versin 4port USB hub that came with the Rocket or R3 or just the store bought USB hub?


Performed a system reboot and scanned for miners again (using MultiMiner/BFGMiner) and it picked up the "missing" blade but within 10 minutes the blade is no longer hashing. I should have time to mess with the drivers and CGMiner soon...working on 3d prints right now

>>> PM me for New ASIC Miner's Info.  We will go check it out <<<
FEEL GENEROUS TODAY?  ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P
R4v37
Sr. Member
****
Offline Offline

Activity: 266
Merit: 250


View Profile
July 12, 2014, 09:36:03 PM
 #572

hmmmm, maybe u guys should build a case like S3 from bitma*n...
am sorry ,but it helps in reducing temp.
and maybe some discount at the price..
i just hoping that u guys also can selling miners like hotcake
mstrongbow
Sr. Member
****
Offline Offline

Activity: 322
Merit: 250

3D Printed!


View Profile
July 12, 2014, 09:49:07 PM
 #573

What kind of USB Hub are you using to connect 4 USB cables?

The bare pcb versin 4port USB hub that came with the Rocket or R3 or just the store bought USB hub?


Performed a system reboot and scanned for miners again (using MultiMiner/BFGMiner) and it picked up the "missing" blade but within 10 minutes the blade is no longer hashing. I should have time to mess with the drivers and CGMiner soon...working on 3d prints right now

I am using the Rockminer supplied 4-port USB hub and routing into a Belkin 7-port hub which I have used for many USB miners (Rockminers, Gridseed and Erupters etc.)
Should I be powering the supplied USB hub from one of the blades with the supplied cable?

    Bitcoin-Scratchticket.com       Win Bitcoin Playing Scratchtickets        Provably Fair   
*Got LootCrate?*
*My Stuff For Sale thread/s*   www.CryptoCause.org   Ask me about SEGMining Hosting!
"Don't undertake a project unless it is manifestly important and nearly impossible" - Edwin Land
Trends
Member
**
Offline Offline

Activity: 119
Merit: 10


View Profile
July 12, 2014, 10:03:20 PM
 #574

I have adjusted the rk-boxes freq's to 320 and rejects have went from 10.95% to 4.68%. I have lost a small amount of ghs but pool side is 460+/- ghs stable(Slush's Pool). The chips are runnings cooler so I have been able to turn the fan down even more. It has also decreased watts a small amount from wall. Everything seems stable for the last 2 hours since my ghs leveled out at pool. Thanks for eveyones help, time to move to the next project.

How did you turn your fan down? Something you added?
Only options in the GUI is Full Speed and Auto

Quadriga CX BTC/CAD Coin Exchange     www.quadrigacx.com/?ref=umvq5t3i2r6im243v94vucbo
mstrongbow
Sr. Member
****
Offline Offline

Activity: 322
Merit: 250

3D Printed!


View Profile
July 12, 2014, 10:06:22 PM
 #575

I have adjusted the rk-boxes freq's to 320 and rejects have went from 10.95% to 4.68%. I have lost a small amount of ghs but pool side is 460+/- ghs stable(Slush's Pool). The chips are runnings cooler so I have been able to turn the fan down even more. It has also decreased watts a small amount from wall. Everything seems stable for the last 2 hours since my ghs leveled out at pool. Thanks for eveyones help, time to move to the next project.

How did you turn your fan down? Something you added?
Only options in the GUI is Full Speed and Auto

I believe he is using an PC fan controller (PCI slot mounted) to throttle down the fan

    Bitcoin-Scratchticket.com       Win Bitcoin Playing Scratchtickets        Provably Fair   
*Got LootCrate?*
*My Stuff For Sale thread/s*   www.CryptoCause.org   Ask me about SEGMining Hosting!
"Don't undertake a project unless it is manifestly important and nearly impossible" - Edwin Land
Trends
Member
**
Offline Offline

Activity: 119
Merit: 10


View Profile
July 12, 2014, 10:09:15 PM
 #576

thanks mstrongbow. I just went back into this thread and saw that 2 or 3 pages back.
I don't think the PWM speed control for the RK or R3 boxes works at all even though the fans are PWM

Quadriga CX BTC/CAD Coin Exchange     www.quadrigacx.com/?ref=umvq5t3i2r6im243v94vucbo
CanaryInTheMine
Donator
Legendary
*
Offline Offline

Activity: 2352
Merit: 1060


between a rock and a block!


View Profile
July 12, 2014, 11:09:56 PM
 #577

hmmmm, maybe u guys should build a case like S3 from bitma*n...
am sorry ,but it helps in reducing temp.
and maybe some discount at the price..
i just hoping that u guys also can selling miners like hotcake
Perhaps R4 will have it Smiley
TrekRider
Newbie
*
Offline Offline

Activity: 56
Merit: 0


View Profile
July 12, 2014, 11:11:13 PM
 #578

hmmmm, maybe u guys should build a case like S3 from bitma*n...
am sorry ,but it helps in reducing temp.
and maybe some discount at the price..
i just hoping that u guys also can selling miners like hotcake
Perhaps R4 will have it Smiley

After getting screwed on 3 RK-Boxes I will not purchase from Rockminer again and urge others to look elsewhere.
CanaryInTheMine
Donator
Legendary
*
Offline Offline

Activity: 2352
Merit: 1060


between a rock and a block!


View Profile
July 12, 2014, 11:14:25 PM
 #579

So the cat is now out of the bag then...
R4 is next release Smiley


2 x R3 in a box.
Maybe 2 halved R3s as one unit encased
Chris_Sabian
Legendary
*
Offline Offline

Activity: 896
Merit: 1001



View Profile
July 12, 2014, 11:24:22 PM
 #580

hmmmm, maybe u guys should build a case like S3 from bitma*n...
am sorry ,but it helps in reducing temp.
and maybe some discount at the price..
i just hoping that u guys also can selling miners like hotcake
Perhaps R4 will have it Smiley

After getting screwed on 3 RK-Boxes I will not purchase from Rockminer again and urge others to look elsewhere.

So, do you get paid to troll?  Every single post that you have made is negative. Welcome to my ignore list.
Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 [29] 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 »
  Print  
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.19 | SMF © 2006-2009, Simple Machines Valid XHTML 1.0! Valid CSS!