bobsag3
|
|
July 12, 2014, 03:57:20 PM |
|
I have a problem connecting more than 2 Rocket Boxen on the raspberry Pi.
When i connect more (4 Boxen) with a good d-link hub between, 16 board are detected and shown, but they are only working with about 70 GH/s.
When i connect the same to a windows pc and using cgminer everything is fine!
The Pi Image does not support more than 2 miners/pi
|
|
|
|
Billbags
Sr. Member
Offline
Activity: 280
Merit: 250
Brainwashed this way
|
|
July 12, 2014, 05:49:16 PM |
|
Any aftermarket fan recommendations for the RK-Box miners? This thing is LOUD and is beginning to bother my tinnitus Thanks! [/quote: I installed a manual fan control on my RK-Boxes that is working well to dramatically reduce the fan noise and still keep the blades cool. Highly reccomended if the Rocket Boxes are in your house. I just lowered fan speed and monitored during the hotest times of the day to get right setting for quiet cooling. I have not had to adjust fan speed since installed and adjusted. Here is the link of the ones I'm using: http://www.amazon.com/gp/aw/d/B004LL8KF6?cache=8dd22ea26140667f1737f48c0bd46cbe&pi=SX200_QL40&qid=1404945076&sr=8-1#ref=mp_s_a_1_1Note: plastic guide on the end of the fan controller wires must be shaved down to fit on the miner. I used a knife, takes about 5 seconds, works well Also, I just got confirmation from Rockminer that the firmware update for the r3 will also work for rk-Box. Doggie has complete firmware update instructions on his r3 setup page. Update: Firmware upgrade instructions for r3 does work with rk-Box with pi. On my two units(each has a pi) I had to ssh with pi then exit, then ssh a second time to allow for update. The first time you ssh to pi a corrupted dadabase error comes up, but once you fully exit and go back in everything works fine and update is applied. You can now adjust freq's at bottom of pools page.
|
|
|
|
CanaryInTheMine
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
July 12, 2014, 06:03:02 PM |
|
So the cat is now out of the bag then... R4 is next release
|
|
|
|
mstrongbow
Sr. Member
Offline
Activity: 322
Merit: 250
3D Printed!
|
|
July 12, 2014, 06:13:10 PM |
|
I will post up with pics later Any aftermarket fan recommendations for the RK-Box miners? This thing is LOUD and is beginning to bother my tinnitus Thanks! [/quote: I installed a manual fan control on my RK-Boxes that is working well to dramatically reduce the fan noise and still keep the blades cool. Highly reccomended if the Rocket Boxes are in your house. I just lowered fan speed and monitored during the hotest times of the day to get right setting for quiet cooling. I have not had to adjust fan speed since installed and adjusted. Here is the link of the ones I'm using: http://www.amazon.com/gp/aw/d/B004LL8KF6?cache=8dd22ea26140667f1737f48c0bd46cbe&pi=SX200_QL40&qid=1404945076&sr=8-1#ref=mp_s_a_1_1Note: plastic guide on the end of the fan controller wires must be shaved down to fit on the miner. I used a knife, takes about 5 seconds, works well Also, I just got confirmation from Rockminer that the firmware update for the r3 will also work for rk-Box. Doggie has complete firmware update instructions on his r3 setup page. Update: Firmware upgrade instructions for r3 does work with rk-Box with pi. On my two units(each has a pi) I had to ssh with pi then exit, then ssh a second time to allow for update. The first time you ssh to pi a corrupted dadabase error comes up, but once you fully exit and go back in everything works fine and update is applied. You can now adjust freq's at bottom of pools page.
|
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
July 12, 2014, 06:44:00 PM |
|
So the cat is now out of the bag then... R4 is next release 2 x R3 in a box.
|
|
|
|
Billbags
Sr. Member
Offline
Activity: 280
Merit: 250
Brainwashed this way
|
|
July 12, 2014, 07:35:50 PM Last edit: July 13, 2014, 05:03:33 AM by Billbags |
|
I have adjusted the rk-boxes freq's to 320 and rejects have went from 10.95% to 4.68%. I have lost a small amount of ghs but pool side is 470+/- ghs stable(Slush's Pool). The chips are runnings cooler so I have been able to turn the fan down even more. It has also decreased watts a small amount from wall. Everything seems stable for the last 2 hours since my ghs leveled out at pool. Thanks for eveyones help, time to move to the next project.
Update: Now pool side is 480+/- ghs stable(Slush's Pool). Same low rejects of 3.75% - 4.79%. Both units really hashing good now. Temps with lower fan speed 41-53 depending on time of day.
|
|
|
|
sushi
Full Member
Offline
Activity: 238
Merit: 100
ASIC Myth Buster
|
|
July 12, 2014, 08:08:14 PM |
|
|
>>> PM me for New ASIC Miner's Info. We will go check it out <<< FEEL GENEROUS TODAY? ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P
|
|
|
mstrongbow
Sr. Member
Offline
Activity: 322
Merit: 250
3D Printed!
|
|
July 12, 2014, 08:23:32 PM |
|
Nice! Just waiting on a replacement R-Pi unit but I will be changing driver to the Zadig driver and playing with CGMiner as BFGMiner does't play well currently. Not only am I getting only 70-80 Gh/s per blade but now only 3/4 blades are hashing
|
|
|
|
sushi
Full Member
Offline
Activity: 238
Merit: 100
ASIC Myth Buster
|
|
July 12, 2014, 08:44:46 PM |
|
Playing with my Rocket Box and R3, you might want to use Cgminer on Rocket gears. If it is hashing low, try to make sure the little control card attached to each hashing PCB seated well and connected well. Then check each USB cables connected okay. Or test just 1 hashing PCB at a time and see if it goes up to 120-130gh/s range. At least it should hit 110/gh For some reasons, if it stuck at 32-40GH/S range, unplug the USB and then plug it back in. If the cgminer doesn't start hashing, restart it and it should be picking up the speed to where it should be. If you are connecting your Rocket Box or R3 to the home internet router or the office router, and for some reasons, it is hashing so low, please try using the different Internet Connection such as Cellphone Hotspot then to the Wi-Fi bridge to test out if using the different Internet Network Setting would resolve your speed issues. (some half speed hashing could be simply the network issues, but it could be the hardware failures, too but it seems more of the network issues than the Rock Gear hardware side) Used to S1 and S2, and now getting used to these Rock Box and R3 x2 pack are hashing at over 900GH/S and when I connect 1 Pi to each Rocket Box or R3, it hashes at over 500GH/s Nice! Just waiting on a replacement R-Pi unit but I will be changing driver to the Zadig driver and playing with CGMiner as BFGMiner does't play well currently. Not only am I getting only 70-80 Gh/s per blade but now only 3/4 blades are hashing
|
>>> PM me for New ASIC Miner's Info. We will go check it out <<< FEEL GENEROUS TODAY? ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P
|
|
|
mstrongbow
Sr. Member
Offline
Activity: 322
Merit: 250
3D Printed!
|
|
July 12, 2014, 08:52:15 PM |
|
Performed a system reboot and scanned for miners again (using MultiMiner/BFGMiner) and it picked up the "missing" blade but within 10 minutes the blade is no longer hashing. I should have time to mess with the drivers and CGMiner soon...working on 3d prints right now
|
|
|
|
sushi
Full Member
Offline
Activity: 238
Merit: 100
ASIC Myth Buster
|
|
July 12, 2014, 09:05:02 PM |
|
What kind of USB Hub are you using to connect 4 USB cables? The bare pcb versin 4port USB hub that came with the Rocket or R3 or just the store bought USB hub? Performed a system reboot and scanned for miners again (using MultiMiner/BFGMiner) and it picked up the "missing" blade but within 10 minutes the blade is no longer hashing. I should have time to mess with the drivers and CGMiner soon...working on 3d prints right now
|
>>> PM me for New ASIC Miner's Info. We will go check it out <<< FEEL GENEROUS TODAY? ==> 1AHNusc3BQA2QJCokySAQ1Qtymr1ZyAG6P
|
|
|
R4v37
|
|
July 12, 2014, 09:36:03 PM |
|
hmmmm, maybe u guys should build a case like S3 from bitma*n... am sorry ,but it helps in reducing temp. and maybe some discount at the price.. i just hoping that u guys also can selling miners like hotcake
|
|
|
|
mstrongbow
Sr. Member
Offline
Activity: 322
Merit: 250
3D Printed!
|
|
July 12, 2014, 09:49:07 PM |
|
What kind of USB Hub are you using to connect 4 USB cables? The bare pcb versin 4port USB hub that came with the Rocket or R3 or just the store bought USB hub? Performed a system reboot and scanned for miners again (using MultiMiner/BFGMiner) and it picked up the "missing" blade but within 10 minutes the blade is no longer hashing. I should have time to mess with the drivers and CGMiner soon...working on 3d prints right now
I am using the Rockminer supplied 4-port USB hub and routing into a Belkin 7-port hub which I have used for many USB miners (Rockminers, Gridseed and Erupters etc.) Should I be powering the supplied USB hub from one of the blades with the supplied cable?
|
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
July 12, 2014, 10:03:20 PM |
|
I have adjusted the rk-boxes freq's to 320 and rejects have went from 10.95% to 4.68%. I have lost a small amount of ghs but pool side is 460+/- ghs stable(Slush's Pool). The chips are runnings cooler so I have been able to turn the fan down even more. It has also decreased watts a small amount from wall. Everything seems stable for the last 2 hours since my ghs leveled out at pool. Thanks for eveyones help, time to move to the next project.
How did you turn your fan down? Something you added? Only options in the GUI is Full Speed and Auto
|
|
|
|
mstrongbow
Sr. Member
Offline
Activity: 322
Merit: 250
3D Printed!
|
|
July 12, 2014, 10:06:22 PM |
|
I have adjusted the rk-boxes freq's to 320 and rejects have went from 10.95% to 4.68%. I have lost a small amount of ghs but pool side is 460+/- ghs stable(Slush's Pool). The chips are runnings cooler so I have been able to turn the fan down even more. It has also decreased watts a small amount from wall. Everything seems stable for the last 2 hours since my ghs leveled out at pool. Thanks for eveyones help, time to move to the next project.
How did you turn your fan down? Something you added? Only options in the GUI is Full Speed and Auto I believe he is using an PC fan controller (PCI slot mounted) to throttle down the fan
|
|
|
|
Trends
Member
Offline
Activity: 119
Merit: 10
|
|
July 12, 2014, 10:09:15 PM |
|
thanks mstrongbow. I just went back into this thread and saw that 2 or 3 pages back. I don't think the PWM speed control for the RK or R3 boxes works at all even though the fans are PWM
|
|
|
|
CanaryInTheMine
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
July 12, 2014, 11:09:56 PM |
|
hmmmm, maybe u guys should build a case like S3 from bitma*n... am sorry ,but it helps in reducing temp. and maybe some discount at the price.. i just hoping that u guys also can selling miners like hotcake
Perhaps R4 will have it
|
|
|
|
TrekRider
Newbie
Offline
Activity: 56
Merit: 0
|
|
July 12, 2014, 11:11:13 PM |
|
hmmmm, maybe u guys should build a case like S3 from bitma*n... am sorry ,but it helps in reducing temp. and maybe some discount at the price.. i just hoping that u guys also can selling miners like hotcake
Perhaps R4 will have it After getting screwed on 3 RK-Boxes I will not purchase from Rockminer again and urge others to look elsewhere.
|
|
|
|
CanaryInTheMine
Donator
Legendary
Offline
Activity: 2352
Merit: 1060
between a rock and a block!
|
|
July 12, 2014, 11:14:25 PM |
|
So the cat is now out of the bag then... R4 is next release 2 x R3 in a box. Maybe 2 halved R3s as one unit encased
|
|
|
|
Chris_Sabian
Legendary
Offline
Activity: 896
Merit: 1001
|
|
July 12, 2014, 11:24:22 PM |
|
hmmmm, maybe u guys should build a case like S3 from bitma*n... am sorry ,but it helps in reducing temp. and maybe some discount at the price.. i just hoping that u guys also can selling miners like hotcake
Perhaps R4 will have it After getting screwed on 3 RK-Boxes I will not purchase from Rockminer again and urge others to look elsewhere. So, do you get paid to troll? Every single post that you have made is negative. Welcome to my ignore list.
|
|
|
|
|