CCminer(SP-MOD) Modded GPU kernels.

[giagge]

No receive lbry payot today on poloniex from https://lbry.suprnova.cc :



Anyone with this problem today ? .

[_javi_]

No receive lbry payot today on poloniex from https://lbry.suprnova.cc :



Anyone with this problem today ? .

same here.. it seems a poloniex issue with wallet

[pallas]

beware of poloniex, they have disabled XCN wallet as well, and for a couple weeks already!!!

[tbearhere]

beware of poloniex, they have disabled XCN wallet as well, and for a couple weeks already!!!

Thx for that info Pallas..

[tbearhere]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

[pallas]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

if used for mining 7/24, the fans will likely break way before the warranty ends.
for mining, ball bearing fans are way more reliable, and I'd say required, unless you sell the cards after a handful of months.

[tbearhere]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

if used for mining 7/24, the fans will likely break way before the warranty ends.
for mining, ball bearing fans are way more reliable, and I'd say required, unless you sell the cards after a handful of months.

Yes was going to see if it had them.
My 2 gigabyte 980ti's all fans are done .. doing an rma on them.
The only cards I'll buy from now on will be with double ball bearings.

[thevictimofuktyranny]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

if used for mining 7/24, the fans will likely break way before the warranty ends.
for mining, ball bearing fans are way more reliable, and I'd say required, unless you sell the cards after a handful of months.

Yes was going to see if it had them.
My 2 gigabyte 980ti's all fans are done .. doing an rma on them.
The only cards I'll buy from now on will be with double ball bearings.

What site do you use to find out ball bearing types?

[bensam1231]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

if used for mining 7/24, the fans will likely break way before the warranty ends.
for mining, ball bearing fans are way more reliable, and I'd say required, unless you sell the cards after a handful of months.

Yes was going to see if it had them.
My 2 gigabyte 980ti's all fans are done .. doing an rma on them.
The only cards I'll buy from now on will be with double ball bearings.

What site do you use to find out ball bearing types?

Personal experience or digging through reviews. Sometimes they're listed on the box. I've mentioned a few different times in this thread for the cards I've bought.

When you first get your fan give it a spin, if it sorta 'wobbles' and then settles like between two grooves it's a ball bear. If it spins freely and just slows down normally it's a sleeve.

Sleeves go bad. Ball bearings go bad, but they take a lot longer and just make a lot of noise while it's happening.

[tbearhere]

@ thevictimofuktyranny
  newegg.com
  usually has it listed if it has them or go to the manufacturers site and look at the different models.

[sp_]

SP, when you wanna release lbry 4th version for donators?

Stupid noob alevlaslo already selling your miner for 0.09 BTC
https://bitcointalk.org/index.php?topic=1610345.msg16502709#msg16502709

As long as ppl are selling cheaper copies I will delay release #4

[thevictimofuktyranny]

@ thevictimofuktyranny
  newegg.com
  usually has it listed if it has them or go to the manufacturers site and look at the different models.

No data, on MSI's Aero exhaust blowers

EVGA is shipping it's 1070 FTW models with dual ball bearings fans (last 4 times as long)!

8 phases to the GPU (1070 reference ships with 4 phases)

EVGA 1070 FTW can draw a total of 215watts - for safe overclocking. Not to mention a free game code in the UK for "Gears of War 4".

Yes, I'm very sad about the 1070's I bought  

Do not watch this review, unless you want to cry like a baby  

https://www.youtube.com/watch?v=ZZpwpEbL3W8

[Amph]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

if used for mining 7/24, the fans will likely break way before the warranty ends.
for mining, ball bearing fans are way more reliable, and I'd say required, unless you sell the cards after a handful of months.

this is the reason why i usually set them at 40% speed, which is the minimum, the other auxiliary fans will do the jobs

[bensam1231]

SP, when you wanna release lbry 4th version for donators?

Stupid noob alevlaslo already selling your miner for 0.09 BTC
https://bitcointalk.org/index.php?topic=1610345.msg16502709#msg16502709

As long as ppl are selling cheaper copies I will delay release #4

So you're punishing your real customers for someone that's ripping you off? WTF dude?

@ thevictimofuktyranny
  newegg.com
  usually has it listed if it has them or go to the manufacturers site and look at the different models.

No data, on MSI's Aero exhaust blowers

EVGA is shipping it's 1070 FTW models with dual ball bearings fans (last 4 times as long)!

8 phases to the GPU (1070 reference ships with 4 phases)

EVGA 1070 FTW can draw a total of 215watts - for safe overclocking. Not to mention a free game code in the UK for "Gears of War 4".

Yes, I'm very sad about the 1070's I bought  

Do not watch this review, unless you want to cry like a baby  

https://www.youtube.com/watch?v=ZZpwpEbL3W8

MSI reds are pieces of shit. I've had over 60% of the ones I bought fail due to faulty VRM circuitry. I literally sent the last five I bought back over the last two months. There is a VRM module that isn't under neath the heatsink that always fails. They get extremely hot and rupture. I've had a few of them actually pop off of the card, one landed on particle board after exploding and started scorching it because it was too hot. It very much could've started a fire if it landed on something with a low burn point.

That said almost all of the 1070s right now come with copies of Gears of War (which people with fake credit cards promptly try to rip you off for on eBay).

Weirdly enough, EVGA/Zotac/MSI are the only manufacturers that sell cards with double PCIE power plugs. Zotac is a PoS due to the armor completely wrapping the exhaust on the card and MSI sells cards with shitty VRM circuitry even though they aren't cheap.

Even Asus models, although they have great coolers (pretty sure they're the best minus triple slot coolers), do not have a double power plug model. That is putting aside blowers, which are the best out of the bunch, but the loudest if you're trying to pack a bunch of cards in a small area. Blower fans DO NOT fail as well, however they're hard to blow out. They use some heavy duty bearings on those. I've never had one go bad.

[_javi_]

Msi 1070 are crap.. 2 failed on me out of 5. I sold the other 3.

Recently i got an EVGA 1070 (the one with the white leds) burning the pci riser slot.

I have very bad luck with the 1070s

I never got such a failure rate with older gpus (Sapphires 7950 and Gigabytes 280x, all fine after 2 years, only fan issues)

[thevictimofuktyranny]

Msi 1070 are crap.. 2 failed on me out of 5. I sold the other 3.

Recently i got an EVGA 1070 (the one with the white leds) burning the pci riser slot.

I have very bad luck with the 1070s

I never got such a failure rate with older gpus (Sapphires 7950 and Gigabytes 280x, all fine after 2 years, only fan issues)

1070 reference design has only 4 phases and most of the early cards shipped with only 4 phases going to the GPU core!

They really don't recommend overclocking anything drawing more than 125watts with only 4 phases going to a GPU or CPU.

So, I'm not a surprised there is a high failure rate when you overclocked them.

AMD tends to put in more phases in their £200 plus cards (RX 480 reference design has 6 phases) and this means safer overclocking outcomes.

[ol92]

SP, when you wanna release lbry 4th version for donators?

Stupid noob alevlaslo already selling your miner for 0.09 BTC
https://bitcointalk.org/index.php?topic=1610345.msg16502709#msg16502709

As long as ppl are selling cheaper copies I will delay release #4

So you're punishing your real customers for someone that's ripping you off? WTF dude?

@ thevictimofuktyranny
  newegg.com
  usually has it listed if it has them or go to the manufacturers site and look at the different models.

No data, on MSI's Aero exhaust blowers

EVGA is shipping it's 1070 FTW models with dual ball bearings fans (last 4 times as long)!

8 phases to the GPU (1070 reference ships with 4 phases)

EVGA 1070 FTW can draw a total of 215watts - for safe overclocking. Not to mention a free game code in the UK for "Gears of War 4".

Yes, I'm very sad about the 1070's I bought  

Do not watch this review, unless you want to cry like a baby  

https://www.youtube.com/watch?v=ZZpwpEbL3W8

MSI reds are pieces of shit. I've had over 60% of the ones I bought fail due to faulty VRM circuitry. I literally sent the last five I bought back over the last two months. There is a VRM module that isn't under neath the heatsink that always fails. They get extremely hot and rupture. I've had a few of them actually pop off of the card, one landed on particle board after exploding and started scorching it because it was too hot. It very much could've started a fire if it landed on something with a low burn point.

That said almost all of the 1070s right now come with copies of Gears of War (which people with fake credit cards promptly try to rip you off for on eBay).

Weirdly enough, EVGA/Zotac/MSI are the only manufacturers that sell cards with double PCIE power plugs. Zotac is a PoS due to the armor completely wrapping the exhaust on the card and MSI sells cards with shitty VRM circuitry even though they aren't cheap.

Even Asus models, although they have great coolers (pretty sure they're the best minus triple slot coolers), do not have a double power plug model. That is putting aside blowers, which are the best out of the bunch, but the loudest if you're trying to pack a bunch of cards in a small area. Blower fans DO NOT fail as well, however they're hard to blow out. They use some heavy duty bearings on those. I've never had one go bad.

No problem with my MSI GTX1080 gaming : the problem on msi 1070 may be linked to the vram used  (micron) : https://www.reddit.com/r/nvidia/comments/4wh8jc/msi_officially_announces_gtx_1070_quality/

[exemplaar]

http://www.gainward.com/main/vgapro.php?id=993&lang=en





Basic model and the cheapest. I like it because it has 2 fans. one 6pin connector and 90watt in the wall. (doesn't need powered risers)  If you oc too much the card will trottle down to the maximum stable speed.

Nice..

if used for mining 7/24, the fans will likely break way before the warranty ends.
for mining, ball bearing fans are way more reliable, and I'd say required, unless you sell the cards after a handful of months.

this is the reason why i usually set them at 40% speed, which is the minimum, the other auxiliary fans will do the jobs

I do not know about GTX 1060, but i still have some Gainward GTX750Ti's in operation. Ball bearing, fans are working at max 66% for more than 2.5years now, without any issue. OC-ed core clock to 1380Mhz.

[thevictimofuktyranny]

Yeah, that could be an issue.

Bought mine's from Scan Computers - it has  the "By Royal Appointment trademark" and the Royal Trademark means everything costs more than Overclockers.UK, Ebuyer and Amazon  

UK version memory runs at slower speeds for Nvidia compute tasks via some bios limitation: 3800mhz and not 4008mhz.

1070's crashed on some of the early drivers, when running some memory intensive crypto algo's like Dagger.

Can't overclock the memory at all, only the GPU cores are stable when overclocked.

However, at stock they work very well and they only use 117watts-122watts.

MSI Aero 1070 8GB using Aero Blower Exhaust

So, the fans should last forever, because the blowers use a heavy duty ball-bearing

Famous last words  

[pallas]

Solution to most of your problems: don't overclock! You will make better use of your electricity and your cards will last much longer.