Yes, I've got 3 im ready to move. Haven't run much at all due to soaring power costs. Probably about a year old, with less than a month of run time on them. I just listed one on eBay for $1750 (to try to offset eBay fees). Still have two that haven't been spoken for. |
|
|
|
Sorry. I wouldn't ship to Norway for a huge unknown.
Economy killed my electric cost.
Would consider hosting with reputable US based facility, or selling outright.
But I'm looking to get about $2k/ea....so if I have to wait for btc to hit $35-40k for that, I will.
My offer of 4500 for the 3 still stands. a realistic comp is like 1700 p/unit. Appreciate the offer, and it is fair. Thank you. It's just hard to justify in my mind to liquidate for $1500/ea when I consider how much I paid for them. And then all the other economic factors.... will my electric cost ever drop? Will btc rise enough to make mining profitable for me again, or rise enough to sell for more? Should I double down and buy more at this lower cost in the event btc goes to 60k again. Not hurting for cash right now, so no emergency. Decisions, decisions. |
|
|
|
|
Sorry. I wouldn't ship to Norway for a huge unknown.
Economy killed my electric cost.
Would consider hosting with reputable US based facility, or selling outright.
But I'm looking to get about $2k/ea....so if I have to wait for btc to hit $35-40k for that, I will.
|
|
|
|
|
I have 3 s19j pros. One is 104th, two are 100th. My electric cost doubled in the last year and I'm not profitable anymore. For the last year, I've been taking turns running them here n there for a few hours. All in all, in great condition. Considering my power cost and price of btc, not sure how long it'll be til I'm profitable again. They're collecting dust right now. I'm considering holding til btc spikes to either run or sell, or cut losses now.
Let me know if you want to talk, and what your budget is. I'm located in PA.
|
|
|
|
|
Thanks for the information (both you above). For some reason, that drop down box wasn't populating the other models, just the hydro. Now it is.
My electric rate doubled in the last year along with btc price going down. So I'm just running one as a space heater for now to offset oil furnace costs.
(Edit) Silly old me.... was clicking the down arrow looking for other models. Nothing populated. Click in the text area and there it was. Updating now
Thanks again
|
|
|
|
|
Saw the Twitter last night. Just signed into Bitmain and only firmware I'm seeing is from 12/15 for the Hydro.
|
|
|
|
do you have 240 volt power?
if you do and your energy cost is zero.
i dont really understand the power side of things yet. we just live in a normal uk house built in the 60s. will the garage support running 10x of these machines without blowing up the house lol. Noise isnt too much of an issue as we have a single detached garage at the rear of the house. but having said that how exactly noisy would 10 machines be? Each unit should be pulling around 12-13 Amps. Here in the US, older houses often have 100a service, newer one have 200a. IF you're lucky enough to have 200a service, I highly doubt you have much more than a 20a/120v line to the garage. So you'd need to come off the main panel with a 100a subpanel, and maybe you can run five 20a/240v circuits from that. I doubt you'd want to run more than five machines based on that. As far as noise, five machines are loud. I was running 5 s17s in my garage, now just 3 s19s. If I'm standing next to them, I can't hear a word you say from a feet feet away. Each unit is like an industrial hair dryer running not stop. You also have hot exhaust to get rid of. Youre probably looking at a few thousand $ worth of electrical work to set up for the machines. Then the machines themselves, and factor in your price per kWh...... at this point, you'd be better off to just buy an entire coin. My electric costs have doubled in the last two years, absolutely killing my profitability. And if you think you'll run 3-5 machines without your dad noticing the power bill going from $300 to $1500, you're nuts. He'll kill you. |
|
|
|
Bitmain puts $150 as the value of the miners on the shipping invoice that goes to customs, so the 25% tariff ends up being around $37.
late reply but this 1000% incorrect. Can confirm. The actual value is stated. So break out the checkbook for Uncle Sam |
|
|
|
|
Just wanted to add. Kaboomracks is legit. You can find their listings in the marketplace section of the forum.
I ordered an S19pro 104 from them on 10/29. It was delivered today, 11/24, and is up and running.
|
|
|
|
Complete Log. Only issue is see is the crc error. Not sure what's causing that. Fell like I need to open it up and check for loose connections [ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.13+ (jenkins@nomd-nomd-fwc-bj) (gcc version 4.9.4 (Linaro GCC 4.9-2017.01) ) #28 SMP Tue Jun 22 17:32:38 CST 2021
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=50c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: Generic AM33XX (Flattened Device Tree), model: TI AM335x BeagleBone
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 65280
[ 0.000000] free_area_init_node: node 0, pgdat c05d9000, node_mem_map c0631000
[ 0.000000] Normal zone: 512 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 64768 pages, LIFO batch:15
[ 0.000000] AM335X ES1.0 (neon )
[ 0.000000] PERCPU: Embedded 8 pages/cpu @c083e000 s9856 r8192 d14720 u32768
[ 0.000000] pcpu-alloc: s9856 r8192 d14720 u32768 alloc=8*4096
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64768
[ 0.000000] Kernel command line: console=ttyO0,115200n8 init=/sbin/init
[ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] allocated 524288 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 255MB = 255MB total
[ 0.000000] Memory: 245448k/245448k available, 16696k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xd0800000 - 0xff000000 ( 744 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf800000 - 0xbfe00000 ( 6 MB)
[ 0.000000] .text : 0xc0008000 - 0xc053f674 (5342 kB)
[ 0.000000] .init : 0xc0540000 - 0xc0571680 ( 198 kB)
[ 0.000000] .data : 0xc0572000 - 0xc05d9ee0 ( 416 kB)
[ 0.000000] .bss : 0xc05d9ee0 - 0xc0630448 ( 346 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER1 at 24000000 Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] OMAP clocksource: GPTIMER2 at 24000000 Hz
[ 0.000000] Console: colour dummy device 80x30
[ 0.000346] Calibrating delay loop... 545.07 BogoMIPS (lpj=531968)
[ 0.015445] pid_max: default: 32768 minimum: 301
[ 0.015666] Security Framework initialized
[ 0.015759] Mount-cache hash table entries: 512
[ 0.024242] Initializing cgroup subsys cpuacct
[ 0.024274] Initializing cgroup subsys memory
[ 0.024336] Initializing cgroup subsys blkio
[ 0.024468] CPU: Testing write buffer coherency: ok
[ 0.024970] CPU0: thread -1, cpu 0, socket -1, mpidr 0
[ 0.025046] Setting up static identity map for 0x8030a500 - 0x8030a54c
[ 0.026412] Brought up 1 CPUs
[ 0.026434] SMP: Total of 1 processors activated (545.07 BogoMIPS).
[ 0.027719] devtmpfs: initialized
[ 0.091402] pinctrl core: initialized pinctrl subsystem
[ 0.091654] rstctl core: initialized rstctl subsystem
[ 0.092125] regulator-dummy: no parameters
[ 0.092621] NET: Registered protocol family 16
[ 0.093280] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.102691] pinctrl-single 44e10800.pinmux: prop pinctrl-0 index 0 invalid phandle
[ 0.102867] pinctrl-single 44e10800.pinmux: 142 pins at pa f9e10800 size 568
[ 0.103917] platform 49000000.edma: alias fck already exists
[ 0.103947] platform 49000000.edma: alias fck already exists
[ 0.103972] platform 49000000.edma: alias fck already exists
[ 0.105085] gpiochip_add: registered GPIOs 0 to 31 on device: gpio
[ 0.105307] OMAP GPIO hardware version 0.1
[ 0.106634] gpiochip_add: registered GPIOs 32 to 63 on device: gpio
[ 0.107938] gpiochip_add: registered GPIOs 64 to 95 on device: gpio
[ 0.109389] gpiochip_add: registered GPIOs 96 to 127 on device: gpio
[ 0.109911] of_get_named_gpio_flags exited with status 52
[ 0.109941] gpio-rctrl rstctl.3: loaded OK
[ 0.114799] omap-gpmc 50000000.gpmc: GPMC revision 6.0
[ 0.118041] hw-breakpoint: debug architecture 0x4 unsupported.
[ 0.119942] cpsw.0: No hwaddr in dt. Using 94:e3:6d:ba:0d:2b from efuse
[ 0.128812] bio: create slab <bio-0> at 0
[ 0.140239] edma-dma-engine edma-dma-engine.0: TI EDMA DMA engine driver
[ 0.140527] of_get_named_gpio_flags: can't parse gpios property
[ 0.140754] vmmcsd_fixed: 3300 mV
[ 0.143862] SCSI subsystem initialized
[ 0.145084] omap_i2c 4819c000.i2c: bus 0 rev0.11 at 100 kHz
[ 0.145115] omap_i2c 4819c000.i2c: unable to select pin group
[ 0.145345] pps_core: LinuxPPS API ver. 1 registered
[ 0.145362] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.146939] Switching to clocksource gp_timer
[ 0.164115] NET: Registered protocol family 2
[ 0.165170] TCP established hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.165258] TCP bind hash table entries: 2048 (order: 3, 40960 bytes)
[ 0.165352] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.165445] TCP: reno registered
[ 0.165471] UDP hash table entries: 256 (order: 1, 12288 bytes)
[ 0.165516] UDP-Lite hash table entries: 256 (order: 1, 12288 bytes)
[ 0.165924] NET: Registered protocol family 1
[ 0.166487] RPC: Registered named UNIX socket transport module.
[ 0.166507] RPC: Registered udp transport module.
[ 0.166520] RPC: Registered tcp transport module.
[ 0.166591] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.166976] Trying to unpack rootfs image as initramfs...
[ 1.055765] Freeing initrd memory: 6448K
[ 1.056392] CPU PMU: probing PMU on CPU 0
[ 1.056424] hw perfevents: enabled with ARMv7 Cortex-A8 PMU driver, 5 counters available
[ 1.056940] omap2_mbox_probe: platform not supported
[ 1.060678] VFS: Disk quotas dquot_6.5.2
[ 1.060922] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.062318] NFS: Registering the id_resolver key type
[ 1.062411] Key type id_resolver registered
[ 1.062427] Key type id_legacy registered
[ 1.062492] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 1.062928] msgmni has been set to 491
[ 1.065768] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 1.065794] io scheduler noop registered
[ 1.065809] io scheduler deadline registered
[ 1.065865] io scheduler cfq registered (default)
[ 1.069560] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.071829] omap_uart 44e09000.serial: did not get pins for uart0 error: -19
[ 1.071854] of_get_named_gpio_flags: can't parse gpios property
[ 1.072130] 44e09000.serial: ttyO0 at MMIO 0x44e09000 (irq = 88) is a OMAP UART0
[ 1.693103] console [ttyO0] enabled
[ 1.697369] of_get_named_gpio_flags: can't parse gpios property
[ 1.697624] 48022000.serial: ttyO1 at MMIO 0x48022000 (irq = 89) is a OMAP UART1
[ 1.706085] of_get_named_gpio_flags: can't parse gpios property
[ 1.706309] 48024000.serial: ttyO2 at MMIO 0x48024000 (irq = 90) is a OMAP UART2
[ 1.714700] of_get_named_gpio_flags: can't parse gpios property
[ 1.714915] 481a8000.serial: ttyO4 at MMIO 0x481a8000 (irq = 61) is a OMAP UART4
[ 1.723351] of_get_named_gpio_flags: can't parse gpios property
[ 1.723569] 481aa000.serial: ttyO5 at MMIO 0x481aa000 (irq = 62) is a OMAP UART5
[ 1.745468] brd: module loaded
[ 1.755697] loop: module loaded
[ 1.759739] bone-capemgr bone_capemgr.8: Failed to find baseboard eeprom node
[ 1.769782] ONFI param page 0 valid
[ 1.773489] ONFI flash detected
[ 1.776816] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABAEAWP), 128MiB, page size: 2048, OOB size: 64
[ 1.788742] omap2-nand: detected x8 NAND flash
[ 1.793408] nand: using OMAP_ECC_BCH8_CODE_HW ECC scheme
[ 1.798991] omap2-nand: using custom ecc layout
[ 1.803842] 12 ofpart partitions found on MTD device omap2-nand.0
[ 1.810240] Creating 12 MTD partitions on "omap2-nand.0":
[ 1.815919] 0x000000000000-0x000000020000 : "spl"
[ 1.822561] 0x000000020000-0x000000040000 : "spl_backup1"
[ 1.829900] 0x000000040000-0x000000060000 : "spl_backup2"
[ 1.837259] 0x000000060000-0x000000080000 : "spl_backup3"
[ 1.844585] 0x000000080000-0x000000240000 : "u-boot"
[ 1.852920] 0x000000240000-0x000000260000 : "bootenv"
[ 1.859865] 0x000000260000-0x000000280000 : "fdt"
[ 1.866509] 0x000000280000-0x000000780000 : "kernel"
[ 1.877459] 0x000000800000-0x000001c00000 : "root"
[ 1.901126] 0x000001c00000-0x000001e00000 : "config"
[ 1.909583] 0x000001e00000-0x000002000000 : "sig"
[ 1.917787] 0x000002000000-0x000008000000 : "nvdata"
[ 2.007009] OneNAND driver initializing
[ 2.013425] mousedev: PS/2 mouse device common for all mice
[ 2.021139] omap_rtc 44e3e000.rtc: rtc core: registered 44e3e000.rtc as rtc0
[ 2.028643] 44e3e000.rtc: already running
[ 2.033149] i2c /dev entries driver
[ 2.037465] pps_ldisc: PPS line discipline registered
[ 2.042953] Driver for 1-wire Dallas network protocol.
[ 2.050164] omap_wdt: OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 2.057738] cpuidle: using governor ladder
[ 2.062068] cpuidle: using governor menu
[ 2.066644] of_get_named_gpio_flags exited with status 6
[ 2.066661] of_get_named_gpio_flags: can't parse gpios property
[ 2.066676] of_get_named_gpio_flags: can't parse gpios property
[ 2.066711] omap_hsmmc mmc.4: of_parse_phandle_with_args of 'reset' failed
[ 2.073940] omap_hsmmc mmc.4: Failed to get rstctl; not using any
[ 2.080792] edma-dma-engine edma-dma-engine.0: allocated channel for 0:25
[ 2.088004] edma-dma-engine edma-dma-engine.0: allocated channel for 0:24
[ 2.095325] mmc.4 supply vmmc_aux not found, using dummy regulator
[ 2.102340] omap_hsmmc mmc.4: pins are not configured from the driver
[ 2.135908] of_get_named_gpio_flags exited with status -517
[ 2.135972] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[ 2.143755] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.150539] edma-dma-engine edma-dma-engine.0: allocated channel for 0:36
[ 2.157760] omap-sham 53100000.sham: hw accel on OMAP rev 4.3
[ 2.165845] omap-aes 53500000.aes: OMAP AES hw accel rev: 3.2
[ 2.172130] edma-dma-engine edma-dma-engine.0: allocated channel for 0:5
[ 2.179314] edma-dma-engine edma-dma-engine.0: allocated channel for 0:6
[ 2.187625] nf_conntrack version 0.5.0 (3935 buckets, 15740 max)
[ 2.195102] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.200881] TCP: cubic registered
[ 2.204425] Initializing XFRM netlink socket
[ 2.209064] NET: Registered protocol family 10
[ 2.215170] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.221133] NET: Registered protocol family 17
[ 2.225912] NET: Registered protocol family 15
[ 2.230733] Key type dns_resolver registered
[ 2.235313] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 2.243394] ThumbEE CPU extension supported.
[ 2.247913] Registering SWP/SWPB emulation handler
[ 2.254021] registered taskstats version 1
[ 2.259788] of_get_named_gpio_flags exited with status -517
[ 2.259859] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[ 2.317019] davinci_mdio 4a101000.mdio: davinci mdio revision 1.6
[ 2.323436] davinci_mdio 4a101000.mdio: detected phy mask fffffffe
[ 2.338233] libphy: 4a101000.mdio: probed
[ 2.342578] davinci_mdio 4a101000.mdio: phy[0]: device 4a101000.mdio:00, driver SMSC LAN8710/LAN8720
[ 2.352662] of_get_named_gpio_flags exited with status -517
[ 2.352729] platform gpio-leds.7: Driver leds-gpio requests probe deferral
[ 2.360212] Detected MACID = 94:e3:6d:ba:0d:2b
[ 2.364891] cpsw 4a100000.ethernet: NAPI disabled
[ 2.371891] omap_rtc 44e3e000.rtc: setting system clock to 2000-01-01 00:00:00 UTC (946684800)
[ 2.381067] cpu0 supply cpu0 not found, using dummy regulator
[ 2.387556] cpufreq_cpu0: failed to scale voltage up: -22
[ 2.393379] cpufreq_cpu0: failed to scale voltage up: -22
[ 2.407083] Freeing init memory: 196K
[ 2.487819] devpts: called with bogus options
[ 2.932519] jffs2: notice: (109) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 5.249239] jffs2: notice: (115) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 5.675216] net eth0: initializing cpsw version 1.12 (0)
[ 5.683512] net eth0: phy found : id is : 0x7c0f1
[ 5.695893] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.758944] libphy: 4a101000.mdio:00 - Link is Up - 100/Full
[ 8.765146] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.265540] register uart_trans chrdev success.
[ 11.270988] tty port open success [/dev/ttyO1]!
[ 11.276039] init sucess for tty struct (249:1) [/dev/ttyO1]
[ 11.282427] tty port open success [/dev/ttyO2]!
[ 11.287894] init sucess for tty struct (249:2) [/dev/ttyO2]
[ 11.294306] tty port open success [/dev/ttyO4]!
[ 11.299292] init sucess for tty struct (249:4) [/dev/ttyO4]
[ 11.305731] tty port open success [/dev/ttyO5]!
[ 11.310647] init sucess for tty struct (249:5) [/dev/ttyO5]
[ 19.725601] uart trans dev open.
[ 19.729278] uart_buf virt addr = 0xccd80000
[ 19.733852] uart_buf phys addr = 0x8cd80000
[ 19.738367] uart_buf pfn = 0x0008cd80
[ 19.744540] uart trans stop send work timer.
[ 19.749531] uart trans set chain exist bits:0x7.
[ 19.754671] uart trans set work queue count 768.
[ 101.768240] uart set baud to: 4098
[ 101.772527] uart set baud to: 4098
[ 101.776367] uart set baud to: 4098
[ 140.862968] uart set baud to: 4109
[ 140.928395] uart set baud to: 4109
[ 140.992614] uart set baud to: 4109
[ 175.096923] uart trans start send work timer.
===========================================Miner log===========================================
2000-01-01 00:00:09 Miner compile time: Tue Jun 22 17:45:49 CST 2021 type: Antminer S19j Pro
2000-01-01 00:00:10 This is fix-freq version
2000-01-01 00:00:10 Miner compile time: Tue Jun 22 17:45:49 CST 2021 type: Antminer S19j Pro
2000-01-01 00:00:10 commit åversion: 93c0f7a 2021-06-22 17:54:06, build by: jenkins 2021-06-22 17:59:34
2000-01-01 00:00:10 opt_multi_version = 1
2000-01-01 00:00:10 opt_bitmain_ab = 1
2000-01-01 00:00:10 mid_auto_gen = 1
2000-01-01 00:00:10 opt_bitmain_work_mode = 0
2000-01-01 00:00:10 port 51 already exported
2000-01-01 00:00:10 port 49 already exported
2000-01-01 00:00:10 port 48 already exported
2000-01-01 00:00:10 port 60 already exported
2000-01-01 00:00:10 port 47 already exported
2000-01-01 00:00:10 port 27 already exported
2000-01-01 00:00:10 port 44 already exported
2000-01-01 00:00:10 port 22 already exported
2000-01-01 00:00:10 no board pluged in socket 44
2000-01-01 00:00:10 port 23 already exported
2000-01-01 00:00:10 port 45 already exported
2000-01-01 00:00:10 port 46 already exported
2000-01-01 00:00:10 port 26 already exported
2000-01-01 00:00:10 Note: front fan is power on!
2000-01-01 00:00:10 Note: rear fan is power on!
2000-01-01 00:00:10 start the http log.
2000-01-01 00:00:10 httpListenThread start ret=0
2000-01-01 00:00:10 start listen on 6060 ...
2000-01-01 00:00:10 load machine BHB42601 conf
2000-01-01 00:00:10 machine : BHB42601
2000-01-01 00:00:10 chain_num 4, chain_domain_num 42, chain_asic_num 126, domain_asic_num 3
2000-01-01 00:00:15 ==========================capability start==========================
2000-01-01 00:00:15 board num = 3
2000-01-01 00:00:15 board id = 0, chain num = 1
2000-01-01 00:00:15 chain id = 0
2000-01-01 00:00:15 board id = 1, chain num = 1
2000-01-01 00:00:15 chain id = 1
2000-01-01 00:00:15 board id = 2, chain num = 1
2000-01-01 00:00:15 chain id = 2
2000-01-01 00:00:15 ==========================capability end============================
2000-01-01 00:00:15 chain num = 3
2000-01-01 00:00:16 load chain 0 eeprom data
2000-01-01 00:00:16 board_info_version = 4
2000-01-01 00:00:16 algorithm_and_key_version = 0x11
2000-01-01 00:00:16 board_sn = FXDZYN3BAJHBA13ZE
2000-01-01 00:00:16 chip_die = ED
2000-01-01 00:00:16 chip_marking = R1C021BH0A
2000-01-01 00:00:16 chip_bin = 5
2000-01-01 00:00:16 ft_version = F1V04B1C1
2000-01-01 00:00:16 pcb_version = 0x130
2000-01-01 00:00:16 bom_version = 0x10
2000-01-01 00:00:16 asic_sensor_type = 0x0
2000-01-01 00:00:16 asic_sensor_addr[0] = 0x0
2000-01-01 00:00:16 asic_sensor_addr[1] = 0x0
2000-01-01 00:00:16 asic_sensor_addr[2] = 0x0
2000-01-01 00:00:16 asic_sensor_addr[3] = 0x0
2000-01-01 00:00:16 pic_sensor_type = 0x8b
2000-01-01 00:00:16 pic_sensor_addr = 0xf
2000-01-01 00:00:16 chip_tech = AC
2000-01-01 00:00:16 board_name = BHB42601
2000-01-01 00:00:16 factory_job = FXDZ20210805003-ZB
2000-01-01 00:00:16 board_info_crc = 0x19
2000-01-01 00:00:16 voltage = 1320
2000-01-01 00:00:16 frequency = 525
2000-01-01 00:00:16 nonce_rate = 9956
2000-01-01 00:00:16 pcb_temp_in = 32
2000-01-01 00:00:16 pcb_temp_out = 34
2000-01-01 00:00:16 test_version = 1
2000-01-01 00:00:16 test_standard = 0
2000-01-01 00:00:16 param_info_crc = 0x1d
2000-01-01 00:00:16 pt1_result = 1
2000-01-01 00:00:16 pt1_count = 2
2000-01-01 00:00:16 pt2_result = 1
2000-01-01 00:00:16 pt2_count = 1
2000-01-01 00:00:17 load chain 1 eeprom data
2000-01-01 00:00:17 board_info_version = 4
2000-01-01 00:00:17 algorithm_and_key_version = 0x11
2000-01-01 00:00:17 board_sn = FXDZYN3BAJHBA0T9Z
2000-01-01 00:00:17 chip_die = ED
2000-01-01 00:00:17 chip_marking = H1C021BD01
2000-01-01 00:00:17 chip_bin = 5
2000-01-01 00:00:17 ft_version = F1V04B1C2
2000-01-01 00:00:17 pcb_version = 0x130
2000-01-01 00:00:17 bom_version = 0x10
2000-01-01 00:00:17 asic_sensor_type = 0x0
2000-01-01 00:00:17 asic_sensor_addr[0] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[1] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[2] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[3] = 0x0
2000-01-01 00:00:17 pic_sensor_type = 0x8b
2000-01-01 00:00:17 pic_sensor_addr = 0xf
2000-01-01 00:00:17 chip_tech = AC
2000-01-01 00:00:17 board_name = BHB42601
2000-01-01 00:00:17 factory_job = FXDZ20210805003-ZB
2000-01-01 00:00:17 board_info_crc = 0x14
2000-01-01 00:00:17 voltage = 1320
2000-01-01 00:00:17 frequency = 525
2000-01-01 00:00:17 nonce_rate = 9995
2000-01-01 00:00:17 pcb_temp_in = 35
2000-01-01 00:00:17 pcb_temp_out = 35
2000-01-01 00:00:17 test_version = 1
2000-01-01 00:00:17 test_standard = 0
2000-01-01 00:00:17 param_info_crc = 0x1b
2000-01-01 00:00:17 pt1_result = 1
2000-01-01 00:00:17 pt1_count = 1
2000-01-01 00:00:17 pt2_result = 1
2000-01-01 00:00:17 pt2_count = 1
2000-01-01 00:00:17 load chain 2 eeprom data
2000-01-01 00:00:17 board_info_version = 4
2000-01-01 00:00:17 algorithm_and_key_version = 0x11
2000-01-01 00:00:17 board_sn = FXDZYN3BAJHBA0GCB
2000-01-01 00:00:17 chip_die = ED
2000-01-01 00:00:17 chip_marking = H1C021BC0A
2000-01-01 00:00:17 chip_bin = 5
2000-01-01 00:00:17 ft_version = F1V04B1C1
2000-01-01 00:00:17 pcb_version = 0x130
2000-01-01 00:00:17 bom_version = 0x10
2000-01-01 00:00:17 asic_sensor_type = 0x0
2000-01-01 00:00:17 asic_sensor_addr[0] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[1] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[2] = 0x0
2000-01-01 00:00:17 asic_sensor_addr[3] = 0x0
2000-01-01 00:00:17 pic_sensor_type = 0x8b
2000-01-01 00:00:17 pic_sensor_addr = 0xf
2000-01-01 00:00:17 chip_tech = AC
2000-01-01 00:00:17 board_name = BHB42601
2000-01-01 00:00:17 factory_job = FXDZ20210805003-ZB
2000-01-01 00:00:17 board_info_crc = 0x19
2000-01-01 00:00:17 voltage = 1320
2000-01-01 00:00:17 frequency = 525
2000-01-01 00:00:17 nonce_rate = 9997
2000-01-01 00:00:17 pcb_temp_in = 34
2000-01-01 00:00:17 pcb_temp_out = 35
2000-01-01 00:00:17 test_version = 1
2000-01-01 00:00:17 test_standard = 0
2000-01-01 00:00:17 param_info_crc = 0x8
2000-01-01 00:00:17 pt1_result = 1
2000-01-01 00:00:17 pt1_count = 2
2000-01-01 00:00:17 pt2_result = 1
2000-01-01 00:00:17 pt2_count = 1
2000-01-01 00:00:17 fan_eft : 0 fan_pwm : 100
2000-01-01 00:00:17 create thread get_nonce_and_register_thread
2000-01-01 00:00:17 fixed working voltage = 1320
2000-01-01 00:00:17 Chain [0] PCB Version: 0x0130
2000-01-01 00:00:17 Chain [0] BOM Version: 0x0010
2000-01-01 00:00:17 Chain [1] PCB Version: 0x0130
2000-01-01 00:00:17 Chain [1] BOM Version: 0x0010
2000-01-01 00:00:17 Chain [2] PCB Version: 0x0130
2000-01-01 00:00:17 Chain [2] BOM Version: 0x0010
2000-01-01 00:00:17 Fan check passed.
2000-01-01 00:00:17 uart_trans addr:0xb6ca6000.
2021-10-30 18:12:04 chain[0] PIC jump to app
2021-10-30 18:12:06 Check chain[0] PIC fw version=0x89
2021-10-30 18:12:07 chain[1] PIC jump to app
2021-10-30 18:12:08 Check chain[1] PIC fw version=0x89
2021-10-30 18:12:10 chain[2] PIC jump to app
2021-10-30 18:12:11 Check chain[2] PIC fw version=0x89
2021-10-30 18:12:11 create thread pic_heart_beat_thread
2021-10-30 18:12:11 max sensor num = 4
2021-10-30 18:12:11 i2c_sim_init start
2021-10-30 18:12:11 temperature_monitor_thread start...
2021-10-30 18:12:11 i2c_sim_init end
2021-10-30 18:12:13 power open power_version = 0x71
2021-10-30 18:12:14 power type version: 0x0071
2021-10-30 18:12:14 Enter sleep to make sure power release finish.
2021-10-30 18:12:25 chain avg vol drop to 0.86
2021-10-30 18:13:20 Slept 65 seconds, diff = 5.
2021-10-30 18:13:21 set_voltage_by_steps to 1500.
2021-10-30 18:13:25 chain avg vol rise to 15.10
2021-10-30 18:13:26 start up min temp by 75a = 25
2021-10-30 18:13:36 Chain[0]: find 126 asic, times 0
2021-10-30 18:13:46 Chain[1]: find 126 asic, times 0
2021-10-30 18:13:55 Chain[2]: find 126 asic, times 0
2021-10-30 18:14:00 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2021-10-30 18:14:05 min freq in eeprom = 525
2021-10-30 18:14:05 fixed frequency is 525
2021-10-30 18:14:05 Bring up temperature is 25
2021-10-30 18:14:05 set UART baud to 3000000
2021-10-30 18:14:05 pulse_mode = 1, ccdly_sel = 0, pwth_sel = 1
2021-10-30 18:14:05 start do_core_reset
2021-10-30 18:14:24 end do_core_reset
2021-10-30 18:14:24 STATUS_INITED: soc init done!
2021-10-30 18:14:24 create thread check_miner_status_thread
2021-10-30 18:14:24 create thread check_system_work_thread
2021-10-30 18:14:27 start to init...
2021-10-30 18:14:27 set_voltage_by_steps to 1450.
2021-10-30 18:14:29 fixed step freq_start = 50, freq_end = 525, freq_step = 6.25
2021-10-30 18:14:29 chain = 0 set freq to 56.25
2021-10-30 18:14:29 chain = 1 set freq to 56.25
2021-10-30 18:14:29 chain = 2 set freq to 56.25
2021-10-30 18:14:29 chain = 0 set freq to 62.50
2021-10-30 18:14:29 chain = 1 set freq to 62.50
2021-10-30 18:14:29 chain = 2 set freq to 62.50
2021-10-30 18:14:29 chain = 0 set freq to 68.75
2021-10-30 18:14:29 chain = 1 set freq to 68.75
2021-10-30 18:14:29 chain = 2 set freq to 68.75
2021-10-30 18:14:29 chain = 0 set freq to 75.00
2021-10-30 18:14:29 chain = 1 set freq to 75.00
2021-10-30 18:14:29 chain = 2 set freq to 75.00
2021-10-30 18:14:29 chain = 0 set freq to 81.25
2021-10-30 18:14:29 chain = 1 set freq to 81.25
2021-10-30 18:14:29 chain = 2 set freq to 81.25
2021-10-30 18:14:29 chain = 0 set freq to 87.50
2021-10-30 18:14:29 chain = 1 set freq to 87.50
2021-10-30 18:14:29 chain = 2 set freq to 87.50
2021-10-30 18:14:29 chain = 0 set freq to 93.75
2021-10-30 18:14:29 chain = 1 set freq to 93.75
2021-10-30 18:14:29 chain = 2 set freq to 93.75
2021-10-30 18:14:29 chain = 0 set freq to 100.00
2021-10-30 18:14:29 chain = 1 set freq to 100.00
2021-10-30 18:14:29 chain = 2 set freq to 100.00
2021-10-30 18:14:30 chain = 0 set freq to 106.25
2021-10-30 18:14:30 chain = 1 set freq to 106.25
2021-10-30 18:14:30 chain = 2 set freq to 106.25
2021-10-30 18:14:30 chain = 0 set freq to 112.50
2021-10-30 18:14:30 chain = 1 set freq to 112.50
2021-10-30 18:14:30 chain = 2 set freq to 112.50
2021-10-30 18:14:30 chain = 0 set freq to 118.75
2021-10-30 18:14:30 chain = 1 set freq to 118.75
2021-10-30 18:14:30 chain = 2 set freq to 118.75
2021-10-30 18:14:30 chain = 0 set freq to 125.00
2021-10-30 18:14:30 chain = 1 set freq to 125.00
2021-10-30 18:14:30 chain = 2 set freq to 125.00
2021-10-30 18:14:30 chain = 0 set freq to 131.25
2021-10-30 18:14:30 chain = 1 set freq to 131.25
2021-10-30 18:14:30 chain = 2 set freq to 131.25
2021-10-30 18:14:30 chain = 0 set freq to 137.50
2021-10-30 18:14:30 chain = 1 set freq to 137.50
2021-10-30 18:14:30 chain = 2 set freq to 137.50
2021-10-30 18:14:30 chain = 0 set freq to 143.75
2021-10-30 18:14:30 chain = 1 set freq to 143.75
2021-10-30 18:14:30 chain = 2 set freq to 143.75
2021-10-30 18:14:30 chain = 0 set freq to 150.00
2021-10-30 18:14:30 chain = 1 set freq to 150.00
2021-10-30 18:14:30 chain = 2 set freq to 150.00
2021-10-30 18:14:30 chain = 0 set freq to 156.25
2021-10-30 18:14:30 chain = 1 set freq to 156.25
2021-10-30 18:14:30 chain = 2 set freq to 156.25
2021-10-30 18:14:30 chain = 0 set freq to 162.50
2021-10-30 18:14:30 chain = 1 set freq to 162.50
2021-10-30 18:14:30 chain = 2 set freq to 162.50
2021-10-30 18:14:31 chain = 0 set freq to 168.75
2021-10-30 18:14:31 chain = 1 set freq to 168.75
2021-10-30 18:14:31 chain = 2 set freq to 168.75
2021-10-30 18:14:31 chain = 0 set freq to 175.00
2021-10-30 18:14:31 chain = 1 set freq to 175.00
2021-10-30 18:14:31 chain = 2 set freq to 175.00
2021-10-30 18:14:31 chain = 0 set freq to 181.25
2021-10-30 18:14:31 chain = 1 set freq to 181.25
2021-10-30 18:14:31 chain = 2 set freq to 181.25
2021-10-30 18:14:31 chain = 0 set freq to 187.50
2021-10-30 18:14:31 chain = 1 set freq to 187.50
2021-10-30 18:14:31 chain = 2 set freq to 187.50
2021-10-30 18:14:31 chain = 0 set freq to 193.75
2021-10-30 18:14:31 chain = 1 set freq to 193.75
2021-10-30 18:14:31 chain = 2 set freq to 193.75
2021-10-30 18:14:31 chain = 0 set freq to 200.00
2021-10-30 18:14:31 chain = 1 set freq to 200.00
2021-10-30 18:14:31 chain = 2 set freq to 200.00
2021-10-30 18:14:31 chain = 0 set freq to 206.25
2021-10-30 18:14:31 chain = 1 set freq to 206.25
2021-10-30 18:14:31 chain = 2 set freq to 206.25
2021-10-30 18:14:31 chain = 0 set freq to 212.50
2021-10-30 18:14:31 chain = 1 set freq to 212.50
2021-10-30 18:14:31 chain = 2 set freq to 212.50
2021-10-30 18:14:31 chain = 0 set freq to 218.75
2021-10-30 18:14:31 chain = 1 set freq to 218.75
2021-10-30 18:14:31 chain = 2 set freq to 218.75
2021-10-30 18:14:31 chain = 0 set freq to 225.00
2021-10-30 18:14:31 chain = 1 set freq to 225.00
2021-10-30 18:14:31 chain = 2 set freq to 225.00
2021-10-30 18:14:32 chain = 0 set freq to 231.25
2021-10-30 18:14:32 chain = 1 set freq to 231.25
2021-10-30 18:14:32 chain = 2 set freq to 231.25
2021-10-30 18:14:32 chain = 0 set freq to 237.50
2021-10-30 18:14:32 chain = 1 set freq to 237.50
2021-10-30 18:14:32 chain = 2 set freq to 237.50
2021-10-30 18:14:32 chain = 0 set freq to 243.75
2021-10-30 18:14:32 chain = 1 set freq to 243.75
2021-10-30 18:14:32 chain = 2 set freq to 243.75
2021-10-30 18:14:32 chain = 0 set freq to 250.00
2021-10-30 18:14:32 chain = 1 set freq to 250.00
2021-10-30 18:14:32 chain = 2 set freq to 250.00
2021-10-30 18:14:32 chain = 0 set freq to 256.25
2021-10-30 18:14:32 chain = 1 set freq to 256.25
2021-10-30 18:14:32 chain = 2 set freq to 256.25
2021-10-30 18:14:32 chain = 0 set freq to 262.50
2021-10-30 18:14:32 chain = 1 set freq to 262.50
2021-10-30 18:14:32 chain = 2 set freq to 262.50
2021-10-30 18:14:32 chain = 0 set freq to 268.75
2021-10-30 18:14:32 chain = 1 set freq to 268.75
2021-10-30 18:14:32 chain = 2 set freq to 268.75
2021-10-30 18:14:32 chain = 0 set freq to 275.00
2021-10-30 18:14:32 chain = 1 set freq to 275.00
2021-10-30 18:14:32 chain = 2 set freq to 275.00
2021-10-30 18:14:32 chain = 0 set freq to 281.25
2021-10-30 18:14:32 chain = 1 set freq to 281.25
2021-10-30 18:14:32 chain = 2 set freq to 281.25
2021-10-30 18:14:33 chain = 0 set freq to 287.50
2021-10-30 18:14:33 chain = 1 set freq to 287.50
2021-10-30 18:14:33 chain = 2 set freq to 287.50
2021-10-30 18:14:33 chain = 0 set freq to 293.75
2021-10-30 18:14:33 chain = 1 set freq to 293.75
2021-10-30 18:14:33 chain = 2 set freq to 293.75
2021-10-30 18:14:33 chain = 0 set freq to 300.00
2021-10-30 18:14:33 chain = 1 set freq to 300.00
2021-10-30 18:14:33 chain = 2 set freq to 300.00
2021-10-30 18:14:33 chain = 0 set freq to 306.25
2021-10-30 18:14:33 chain = 1 set freq to 306.25
2021-10-30 18:14:33 chain = 2 set freq to 306.25
2021-10-30 18:14:33 chain = 0 set freq to 312.50
2021-10-30 18:14:33 chain = 1 set freq to 312.50
2021-10-30 18:14:33 chain = 2 set freq to 312.50
2021-10-30 18:14:33 chain = 0 set freq to 318.75
2021-10-30 18:14:33 chain = 1 set freq to 318.75
2021-10-30 18:14:33 chain = 2 set freq to 318.75
2021-10-30 18:14:33 chain = 0 set freq to 325.00
2021-10-30 18:14:33 chain = 1 set freq to 325.00
2021-10-30 18:14:33 chain = 2 set freq to 325.00
2021-10-30 18:14:33 chain = 0 set freq to 331.25
2021-10-30 18:14:33 chain = 1 set freq to 331.25
2021-10-30 18:14:33 chain = 2 set freq to 331.25
2021-10-30 18:14:33 chain = 0 set freq to 337.50
2021-10-30 18:14:33 chain = 1 set freq to 337.50
2021-10-30 18:14:33 chain = 2 set freq to 337.50
2021-10-30 18:14:33 chain = 0 set freq to 343.75
2021-10-30 18:14:33 chain = 1 set freq to 343.75
2021-10-30 18:14:33 chain = 2 set freq to 343.75
2021-10-30 18:14:34 chain = 0 set freq to 350.00
2021-10-30 18:14:34 chain = 1 set freq to 350.00
2021-10-30 18:14:34 chain = 2 set freq to 350.00
2021-10-30 18:14:34 chain = 0 set freq to 356.25
2021-10-30 18:14:34 chain = 1 set freq to 356.25
2021-10-30 18:14:34 chain = 2 set freq to 356.25
2021-10-30 18:14:34 chain = 0 set freq to 362.50
2021-10-30 18:14:34 chain = 1 set freq to 362.50
2021-10-30 18:14:34 chain = 2 set freq to 362.50
2021-10-30 18:14:34 chain = 0 set freq to 368.75
2021-10-30 18:14:34 chain = 1 set freq to 368.75
2021-10-30 18:14:34 chain = 2 set freq to 368.75
2021-10-30 18:14:34 chain = 0 set freq to 375.00
2021-10-30 18:14:34 chain = 1 set freq to 375.00
2021-10-30 18:14:34 chain = 2 set freq to 375.00
2021-10-30 18:14:34 chain = 0 set freq to 381.25
2021-10-30 18:14:34 chain = 1 set freq to 381.25
2021-10-30 18:14:34 chain = 2 set freq to 381.25
2021-10-30 18:14:34 chain = 0 set freq to 387.50
2021-10-30 18:14:34 chain = 1 set freq to 387.50
2021-10-30 18:14:34 chain = 2 set freq to 387.50
2021-10-30 18:14:34 chain = 0 set freq to 393.75
2021-10-30 18:14:34 chain = 1 set freq to 393.75
2021-10-30 18:14:34 chain = 2 set freq to 393.75
2021-10-30 18:14:34 chain = 0 set freq to 400.00
2021-10-30 18:14:34 chain = 1 set freq to 400.00
2021-10-30 18:14:34 chain = 2 set freq to 400.00
2021-10-30 18:14:35 chain = 0 set freq to 406.25
2021-10-30 18:14:35 chain = 1 set freq to 406.25
2021-10-30 18:14:35 chain = 2 set freq to 406.25
2021-10-30 18:14:35 chain = 0 set freq to 412.50
2021-10-30 18:14:35 chain = 1 set freq to 412.50
2021-10-30 18:14:35 chain = 2 set freq to 412.50
2021-10-30 18:14:35 chain = 0 set freq to 418.75
2021-10-30 18:14:35 chain = 1 set freq to 418.75
2021-10-30 18:14:35 chain = 2 set freq to 418.75
2021-10-30 18:14:35 chain = 0 set freq to 425.00
2021-10-30 18:14:35 chain = 1 set freq to 425.00
2021-10-30 18:14:35 chain = 2 set freq to 425.00
2021-10-30 18:14:35 chain = 0 set freq to 431.25
2021-10-30 18:14:35 chain = 1 set freq to 431.25
2021-10-30 18:14:35 chain = 2 set freq to 431.25
2021-10-30 18:14:35 chain = 0 set freq to 437.50
2021-10-30 18:14:35 chain = 1 set freq to 437.50
2021-10-30 18:14:35 chain = 2 set freq to 437.50
2021-10-30 18:14:35 chain = 0 set freq to 443.75
2021-10-30 18:14:35 chain = 1 set freq to 443.75
2021-10-30 18:14:35 chain = 2 set freq to 443.75
2021-10-30 18:14:35 chain = 0 set freq to 450.00
2021-10-30 18:14:35 chain = 1 set freq to 450.00
2021-10-30 18:14:35 chain = 2 set freq to 450.00
2021-10-30 18:14:35 chain = 0 set freq to 456.25
2021-10-30 18:14:35 chain = 1 set freq to 456.25
2021-10-30 18:14:35 chain = 2 set freq to 456.25
2021-10-30 18:14:35 chain = 0 set freq to 462.50
2021-10-30 18:14:35 chain = 1 set freq to 462.50
2021-10-30 18:14:35 chain = 2 set freq to 462.50
2021-10-30 18:14:36 chain = 0 set freq to 468.75
2021-10-30 18:14:36 chain = 1 set freq to 468.75
2021-10-30 18:14:36 chain = 2 set freq to 468.75
2021-10-30 18:14:36 chain = 0 set freq to 475.00
2021-10-30 18:14:36 chain = 1 set freq to 475.00
2021-10-30 18:14:36 chain = 2 set freq to 475.00
2021-10-30 18:14:36 chain = 0 set freq to 481.25
2021-10-30 18:14:36 chain = 1 set freq to 481.25
2021-10-30 18:14:36 chain = 2 set freq to 481.25
2021-10-30 18:14:36 chain = 0 set freq to 487.50
2021-10-30 18:14:36 chain = 1 set freq to 487.50
2021-10-30 18:14:36 chain = 2 set freq to 487.50
2021-10-30 18:14:36 chain = 0 set freq to 493.75
2021-10-30 18:14:36 chain = 1 set freq to 493.75
2021-10-30 18:14:36 chain = 2 set freq to 493.75
2021-10-30 18:14:36 chain = 0 set freq to 500.00
2021-10-30 18:14:36 chain = 1 set freq to 500.00
2021-10-30 18:14:36 chain = 2 set freq to 500.00
2021-10-30 18:14:36 chain = 0 set freq to 506.25
2021-10-30 18:14:36 chain = 1 set freq to 506.25
2021-10-30 18:14:36 chain = 2 set freq to 506.25
2021-10-30 18:14:36 chain = 0 set freq to 512.50
2021-10-30 18:14:36 chain = 1 set freq to 512.50
2021-10-30 18:14:36 chain = 2 set freq to 512.50
2021-10-30 18:14:36 chain = 0 set freq to 518.75
2021-10-30 18:14:36 chain = 1 set freq to 518.75
2021-10-30 18:14:36 chain = 2 set freq to 518.75
2021-10-30 18:14:36 chain = 0 set freq to 525.00
2021-10-30 18:14:36 chain = 1 set freq to 525.00
2021-10-30 18:14:36 chain = 2 set freq to 525.00
2021-10-30 18:14:37 set_voltage_by_steps to 1320.
2021-10-30 18:14:39 Init done!
2021-10-30 18:14:39 STATUS_OKAY
2021-10-30 18:14:39 start the cached job
2021-10-30 18:14:39 Version num 65536
2021-10-30 18:14:39 Mask num 0x1fffe000
2021-10-30 18:14:39 opt_multi_version = 65536, interval timeout = 2945120
2021-10-30 18:14:39 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2021-10-30 18:14:39 set_start_time_point total_tv_start_sys=176 total_tv_end_sys=177
2021-10-30 18:14:39 set_voltage_by_steps to 1350.
2021-10-30 18:15:38 set_voltage_by_steps to 1340.
2021-10-30 18:15:40 set_voltage_by_steps to 1330.
2021-10-30 18:15:42 set_voltage_by_steps to 1320.
2021-10-30 18:15:56 !!! nonce crc error
2021-10-30 18:15:58 !!! nonce crc error
2021-10-30 18:16:00 !!! nonce crc error
2021-10-30 18:16:02 !!! reg crc error
2021-10-30 18:16:03 !!! nonce crc error
2021-10-30 18:16:03 !!! nonce crc error
2021-10-30 18:16:03 !!! nonce crc error
2021-10-30 18:16:06 !!! nonce crc error
2021-10-30 18:16:06 !!! nonce crc error
2021-10-30 18:16:15 !!! nonce crc error
2021-10-30 18:16:18 !!! nonce crc error
2021-10-30 18:16:20 !!! nonce crc error
2021-10-30 18:16:25 !!! nonce crc error
2021-10-30 18:16:27 !!! nonce crc error
2021-10-30 18:16:28 !!! nonce crc error
2021-10-30 18:16:39 !!! nonce crc error
2021-10-30 18:16:43 !!! nonce crc error
2021-10-30 18:16:45 !!! nonce crc error
2021-10-30 18:16:53 !!! nonce crc error
2021-10-30 18:17:02 !!! nonce crc error
2021-10-30 18:17:09 !!! reg crc error
2021-10-30 18:17:10 !!! nonce crc error
2021-10-30 18:17:11 !!! nonce crc error
2021-10-30 18:17:20 !!! nonce crc error
2021-10-30 18:17:30 !!! nonce crc error
2021-10-30 18:17:43 !!! nonce crc error
2021-10-30 18:17:58 !!! nonce crc error
2021-10-30 18:21:04 !!! nonce crc error
2021-10-30 18:21:30 !!! nonce crc error
2021-10-30 18:22:24 !!! nonce crc error
2021-10-30 18:22:24 !!! nonce crc error
2021-10-30 18:22:26 !!! nonce crc error
2021-10-30 18:22:27 !!! nonce crc error
2021-10-30 18:22:28 !!! nonce crc error
2021-10-30 18:22:34 !!! nonce crc error
2021-10-30 18:22:43 !!! nonce crc error
2021-10-30 18:22:43 !!! nonce crc error
2021-10-30 18:22:45 !!! nonce crc error
2021-10-30 18:22:45 !!! nonce crc error
2021-10-30 18:22:45 !!! nonce crc error
2021-10-30 18:22:56 !!! nonce crc error
2021-10-30 18:23:00 !!! reg crc error
2021-10-30 18:23:08 !!! nonce crc error
2021-10-30 18:23:15 !!! nonce crc error
2021-10-30 18:23:25 !!! reg crc error
2021-10-30 18:23:25 !!! nonce crc error
2021-10-30 18:23:28 !!! nonce crc error
2021-10-30 18:23:30 !!! nonce crc error
2021-10-30 18:23:36 !!! nonce crc error
2021-10-30 18:23:36 !!! nonce crc error
2021-10-30 18:23:43 !!! nonce crc error
2021-10-30 18:23:44 !!! nonce crc error
2021-10-30 18:24:09 !!! nonce crc error
2021-10-30 18:24:11 !!! nonce crc error
2021-10-30 18:24:24 !!! nonce crc error
2021-10-30 18:24:26 !!! nonce crc error
2021-10-30 18:24:32 !!! nonce crc error
2021-10-30 18:24:34 !!! nonce crc error
2021-10-30 18:24:35 !!! nonce crc error
2021-10-30 18:24:38 !!! nonce crc error
2021-10-30 18:24:46 !!! nonce crc error
2021-10-30 18:24:49 !!! nonce crc error
2021-10-30 18:24:51 !!! nonce crc error
2021-10-30 18:24:53 !!! nonce crc error
2021-10-30 18:25:07 !!! nonce crc error
2021-10-30 18:25:12 !!! nonce crc error
2021-10-30 18:25:54 !!! nonce crc error
2021-10-30 18:26:00 !!! nonce crc error
2021-10-30 18:26:00 !!! nonce crc error
2021-10-30 18:26:01 !!! nonce crc error
2021-10-30 18:27:13 !!! nonce crc error
2021-10-30 18:27:18 !!! reg crc error
2021-10-30 18:32:46 !!! reg crc error
2021-10-30 18:33:36 !!! nonce crc error
2021-10-30 18:33:49 !!! nonce crc error
2021-10-30 18:34:11 !!! nonce crc error
2021-10-30 18:34:35 !!! nonce crc error
2021-10-30 18:35:31 !!! nonce crc error
2021-10-30 18:35:42 !!! nonce crc error
2021-10-30 18:38:04 !!! nonce crc error
2021-10-30 18:38:04 !!! nonce crc error
2021-10-30 18:38:17 !!! nonce crc error
2021-10-30 18:39:22 !!! nonce crc error
2021-10-30 18:39:57 !!! nonce crc error
2021-10-30 18:41:16 !!! nonce crc error
2021-10-30 18:41:17 !!! nonce crc error |
|
|
|
|
Got some S19pro 100th units set up yesterday and everything fired up perfect. Today I notice one board on one unit isn't hashing at full rate. A half dozen reboots and a factory reset hasn't fixed the problem. Airflow is good, temps are good, and I replaced the Ethernet cable to be safe.
Each board should run 34th. Board #1 fires up just like the others and goes to 34th. Then, over the next several minutes, it's will slowly drop to about 24th and sit there.
The error I see in the log is this:
2021-10-30 18:14:39 Init done!
2021-10-30 18:14:39 STATUS_OKAY
2021-10-30 18:14:39 start the cached job
2021-10-30 18:14:39 Version num 65536
2021-10-30 18:14:39 Mask num 0x1fffe000
2021-10-30 18:14:39 opt_multi_version = 65536, interval timeout = 2945120
2021-10-30 18:14:39 freq = 525, percent = 90, hcn = 4993, timeout = 2945120
2021-10-30 18:14:39 set_start_time_point total_tv_start_sys=176 total_tv_end_sys=177
2021-10-30 18:14:39 set_voltage_by_steps to 1350.
2021-10-30 18:15:38 set_voltage_by_steps to 1340.
2021-10-30 18:15:40 set_voltage_by_steps to 1330.
2021-10-30 18:15:42 set_voltage_by_steps to 1320.
2021-10-30 18:15:56 !!! nonce crc error
2021-10-30 18:15:58 !!! nonce crc error
2021-10-30 18:16:00 !!! nonce crc error
2021-10-30 18:16:02 !!! reg crc error
2021-10-30 18:16:03 !!! nonce crc error
2021-10-30 18:16:03 !!! nonce crc error
2021-10-30 18:16:03 !!! nonce crc error
2021-10-30 18:16:06 !!! nonce crc error
2021-10-30 18:16:06 !!! nonce crc error
2021-10-30 18:16:15 !!! nonce crc error
2021-10-30 18:16:18 !!! nonce crc error
2021-10-30 18:16:20 !!! nonce crc error
2021-10-30 18:16:25 !!! nonce crc error
2021-10-30 18:16:27 !!! nonce crc error
2021-10-30 18:16:28 !!! nonce crc error
2021-10-30 18:16:39 !!! nonce crc error
2021-10-30 18:16:43 !!! nonce crc error
2021-10-30 18:16:45 !!! nonce crc error
2021-10-30 18:16:53 !!! nonce crc error
2021-10-30 18:17:02 !!! nonce crc error
2021-10-30 18:17:09 !!! reg crc error
2021-10-30 18:17:10 !!! nonce crc error
2021-10-30 18:17:11 !!! nonce crc error
2021-10-30 18:17:20 !!! nonce crc error
2021-10-30 18:17:30 !!! nonce crc error
2021-10-30 18:17:43 !!! nonce crc error
Any ideas? Loose connection somewhere?
|
|
|
|
Hong Kong has very few component production companies or assembly factories and where the major production of sub assemblies and final assembly occurs is what matters. In other words most of Bitmain miners are Made In China. Not sure if BM still runs any Malaysian factories that they used to get around the tariff regulations.
Yer just going to have to wait and see.
Units arrived today, after I was contacted by UPS yesterday. And the answer is..... YES. I did have to pay the 25% tariff. |
|
|
|
I had problems with my s17s after a year (S/T15s were even worse!) Sold them all and moved to S19s. One failed during warranty and bitmain swapped it out very quickly. It gets hot and humid here so I take extra precaution during the summer to keep miners under 95F. Heat and humidity kills all miners. If you are running where it is cold you should not have these issues. I think they are about the same quality-wise. I really liked my first S19pro but then when the issues started I moved them to cool environment and have not had any problems for 4-5 months.
Appreciate the response. Didn't have many problems with my s17s. I'm in a cooler climate and my airflow is excellent where they're set up. But when I did have a problem, usually after about a year, it was almost impossible to ship them out and get them back without heat sinks coming off in shipment. I did do some research after my initial post and learned the S19 has a different heat sink design. Got all my s17s sold on eBay, and ordered a few s19s from bitmain. Can't complain, I easily got 3x or more selling them than what I paid for them 12-18mo prior. Was afraid they were reaching the end of their life in terms of reliability, so got rid of them before they were worth nothing. |
|
|
|
|
Is anyone aware of any current tariff information regarding China vs Hong Kong origin? I recall Hong Kong previously being declared autonomous from China, and the 25% tariff not being applicable to items originating from HK.
I got shipping information from Bitmain today and tracking shows it originating in HK. Which offers a glimmer of hope to avoid tariff. But I also recall possibly seeing information that rules changed, HK being declared "not autonomous enough", and items from HK needed to be labeled as made in China.
Anyone have actual knowledge or recent experience, or am I just gonna wait and see?
|
|
|
|
|
As some of you may or may not know, I'm just a home garage miner, so I'm looking for some input from the pros.
I was running five S17+73's for a while, but as they age, problems pop up. Temp sensor is usually the culprit.
So one of the units dropped a board and I just sold it running 2/3's as is to a guy for $3300 a few months ago. Felt that was fine. It was more than I paid for it.
Then another one dropped a board. Same issue. Sent it out for repair and was told it had too many bad chips for them to repair. Got it back today and it sound like a box of marbles. Obviously most, or all of the heat sinks came loose during shipping.
So now I have one brick, and three running units.
I'm considering selling everything I currently have, before they also die due to age.
I did some math, and running two S19pro 100's would be more profitable than my current three S17s.
Money wise... I think I can sell my current set up for close to what I would pay for new S19's. The difference would be recoup'd in a month or two.
So my main question to the folks that know....please tell me the S19s have better heat sink engineering. I'd like something to last more than a year before it gives me issues.
|
|
|
|
Just shipped off an S17+ 73 to NH today (Fri). My first dealing with the new authorized Bitmain service location. Www.Greatvoyage.comEmail communication so far has been good. They should receive it Wed. I'll update with results Was just notified today that upon initial testing, they found two boards with more than 5 bad chips on them. Thus, they cannot repair the miner and will be shipping it back to me. That's sad to hear, after almost 20 days since they received the miner, and they can't fix it! why can't they fix 5 chips, I don't think that's a good enough reason, if they can fix one they can fix 5 or 6 or even 10 no? based on what I know, identifying the bad chips takes more time and effort than actually replacing them, so if they really got to that point, why stop? Is it because they don't have both BM1397AG and BM1397AD? I think it's because their repair price of $150/board includes up to 5 chips. And this exceeds 5... and once 5 chips is exceeded, it would be more practical to change the entire board. Let me copy n paste their email: "Sorry for late reply. Your miner (SN#:deleted) took the initial test. Two hash boards is not good. Both boards have over 5 bad chips which is unrepairable situation. So we consider shipping your miner back to you. we'll send you the payment invoice for shipping. After we got the payment, we'll arrange shipping." "Most of the chips on the boards are at the end of their working life. $150 cannot cover over 5 new chips price. The cost for replace all the bad chips may be enough for a new hash board!! So over 5 bad chips is identify unrepairable. " Update. 10/2/21. Got the miner back today via FedEx. Worse shape than when I sent it. Took the miner out of the box and I'd have to guess about 20 heat sinks came loose. Sounds like a box of marbles in there. Not even gonna bother trying to plug it in. Was running on 2/3 boards when I shipped it, Now I have a brick. Update. 10/12/21. I sold the miner as-is inoperable to a guy in CO. Learned he has a miner repair business, so buying broken miners is a side hobby. He received the miner today, inspected it and gave me a call. He thought I'd want to know... he said two boards have definitely been "messed with." He said some chips were replaced, but heat sinks weren't attached to those chips. (Not the "we can't fix it so we'll send it back" situation they told me). He believes GreatVoyage did one of two things..... Either they, 1. Started changing out chips and gave up mid-repair, or 2. (More likely). They took two of my good boards and pulled the old switcharoo, putting two bad boards into my machine and sending it back. Considering they are an "authorized" Bitmain repair location, would they get more money doing a warranty repair for Bitmain, or a $150 from independent little me? Remember, I sent this one unit off......with zero loose heat sinks, and the only error I was seeing was it failing to detect one temp sensor. |
|
|
|
Just shipped off an S17+ 73 to NH today (Fri). My first dealing with the new authorized Bitmain service location. Www.Greatvoyage.comEmail communication so far has been good. They should receive it Wed. I'll update with results Was just notified today that upon initial testing, they found two boards with more than 5 bad chips on them. Thus, they cannot repair the miner and will be shipping it back to me. |
|
|
|
Yes sir, as is stated in post #1 |
|
|
|
Just shipped off an S17+ 73 to NH today (Fri). My first dealing with the new authorized Bitmain service location. Www.Greatvoyage.comEmail communication so far has been good. They should receive it Wed. I'll update with results |
|
|
|
|
So I have another unit down a board. Looking for repair locations again. Got a response from Myrig with a ticket # and shipping address. I searched the address... and it's a UPS store. I'm hesitant
|
|
|
|
|
Show Posts
