delle54
|
|
December 04, 2016, 11:31:13 PM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB.
|
|
|
|
DStefanov
|
|
December 04, 2016, 11:41:08 PM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true?
|
|
|
|
suggsy89
|
|
December 04, 2016, 11:45:08 PM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again.
|
|
|
|
DStefanov
|
|
December 04, 2016, 11:50:00 PM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx?
|
|
|
|
suggsy89
|
|
December 04, 2016, 11:55:12 PM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx? Well i use setx as global, I don't think there is a "proper" way, you either set it temporary or permanently. I guess if you have various different cards you would use set, and if they were all the same use setx.
|
|
|
|
SASAMMM
Newbie
Offline
Activity: 7
Merit: 0
|
|
December 05, 2016, 12:00:25 AM |
|
Claymore has a full mining speed from the start(v1) .no one sees but my? He simultaneously works with pools and exchanges and zcash team. Look at the Poloniex pump and dump and release of new miners (time) His job is to prevent too large price decrease.Price now is unreal high. There is no race.everything is pre-planned. Slow start is over.There is still one final release,and that's it. One more pump and price go down.(because he does not hurry with the latest version) Game is over.
|
|
|
|
DStefanov
|
|
December 05, 2016, 12:03:14 AM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx? Well i use setx as global, I don't think there is a "proper" way, you either set it temporary or permanently. I guess if you have various different cards you would use set, and if they were all the same use setx. My cards is all the same /RX480 Nitro+ OC 8 GB/ and i will use setx! Thanks!
|
|
|
|
melloyellow
|
|
December 05, 2016, 12:08:41 AM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx? Well i use setx as global, I don't think there is a "proper" way, you either set it temporary or permanently. I guess if you have various different cards you would use set, and if they were all the same use setx. My cards is all the same /RX480 Nitro+ OC 8 GB/ and i will use setx! Thanks! set needs = setx doesn't so good thing that you're going to use setx
|
|
|
|
xeridea
|
|
December 05, 2016, 12:42:48 AM |
|
guys have some questions that bothers me...
just added in my rig today an HD 8990, to another 3x R9 390 gigabite 8 gb, with a Ewga supernova 1300w G2 PSU... The consuption is 1327w at wall...
Also have an Therma Take Though power 1200w PSU which is running at 1130w at wall....
where is the limit of the PSU consuption in long term? Any experience/advice?
Just dont wanna burn them in short time...
next, where is the difference between the MSI afterburner setting and setting the settings in the crimson software? for me are the setting possibilities same, or i missing something?
pls teach me...
Many thanks for any advice and help....
Take the 1130w at wall, and figure out what it is outputting by multiplying by efficiency (can estimate based on 80+ level, https://en.wikipedia.org/wiki/80_Plus). Some say to not go over 80% load for 24/7, others say you can go higher if it is a quality PSU. Stability may be better not at high load, but depends on quality of PSU also. Look up Johny GURU review of your PSU. Or perhaps look here http://www.tomshardware.com/forum/id-2547993/psu-tier-list.html
|
Profitability over time charts for many GPUs - http://xeridea.us/chartsBTC: bc1qr2xwjwfmjn43zhrlp6pn7vwdjrjnv5z0anhjhn LTC: LXDm6sR4dkyqtEWfUbPumMnVEiUFQvxSbZ Eth: 0x44cCe2cf90C8FEE4C9e4338Ae7049913D4F6fC24
|
|
|
manotroll
|
|
December 05, 2016, 01:03:33 AM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx? Well i use setx as global, I don't think there is a "proper" way, you either set it temporary or permanently. I guess if you have various different cards you would use set, and if they were all the same use setx. My cards is all the same /RX480 Nitro+ OC 8 GB/ and i will use setx! Thanks! set needs = setx doesn't so good thing that you're going to use setx use setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_FORCE_64BIT_PTR 0 setx GPU_MAX_HEAP_SIZE 100 setx GPU_USE_SYNC_OBJECTS 1 setx GPU_SINGLE_ALLOC_PERCENT 100
|
|
|
|
QuintLeo
Legendary
Offline
Activity: 1498
Merit: 1030
|
|
December 05, 2016, 01:43:30 AM |
|
you will not tell me if I can ask a question on an open forum you twat!!!unbelievable the people here that feel the need to answer for
Just keep your spam for yourself, be patient and don't bother us. There is an "ignore" function for a reason.
|
I'm no longer legendary just in my own mind! Like something I said? Donations gratefully accepted. LYLnTKvLefz9izJFUvEGQEZzSkz34b3N6U (Litecoin) 1GYbjMTPdCuV7dci3iCUiaRrcNuaiQrVYY (Bitcoin)
|
|
|
AlcatelBravo
Full Member
Offline
Activity: 143
Merit: 100
Alfa, Bravo, Charlie, Delta, Echo, Foxtrot....
|
|
December 05, 2016, 02:03:34 AM |
|
you will not tell me if I can ask a question on an open forum you twat!!!unbelievable the people here that feel the need to answer for
Just keep your spam for yourself, be patient and don't bother us. There is an "ignore" function for a reason. I wonder what is the maximum amount of ignores that someone has on their list, threads would be very quiet for them I take it lol
|
When in doubt, dig it out.
|
|
|
Puffy23
Member
Offline
Activity: 108
Merit: 11
|
|
December 05, 2016, 02:15:35 AM |
|
guys have some questions that bothers me...
just added in my rig today an HD 8990, to another 3x R9 390 gigabite 8 gb, with a Ewga supernova 1300w G2 PSU... The consuption is 1327w at wall...
Also have an Therma Take Though power 1200w PSU which is running at 1130w at wall....
where is the limit of the PSU consuption in long term? Any experience/advice?
Just dont wanna burn them in short time...
next, where is the difference between the MSI afterburner setting and setting the settings in the crimson software? for me are the setting possibilities same, or i missing something?
pls teach me...
Many thanks for any advice and help....
Most PSUs achieve maximum efficiency around 50% load. The cost of doubling your power requirement usually washes any profits from extra efficiency though. For longevity you should aim to load them around 80% (or less if you want the gains in efficiency).
|
|
|
|
rpg
|
|
December 05, 2016, 03:39:54 AM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx? Well i use setx as global, I don't think there is a "proper" way, you either set it temporary or permanently. I guess if you have various different cards you would use set, and if they were all the same use setx. When you use setx will stay there forever. You have to go to the registry and manually remove it under currentuser\environment
|
|
|
|
Jmme
Newbie
Offline
Activity: 10
Merit: 0
|
|
December 05, 2016, 03:50:23 AM |
|
I think you guys need to start your own thread so you can keep quoting each other until each post is a full fucking page.
|
|
|
|
AlcatelBravo
Full Member
Offline
Activity: 143
Merit: 100
Alfa, Bravo, Charlie, Delta, Echo, Foxtrot....
|
|
December 05, 2016, 03:54:37 AM |
|
Claymore has a full mining speed from the start(v1) .no one sees but my? He simultaneously works with pools and exchanges and zcash team. Look at the Poloniex pump and dump and release of new miners (time) His job is to prevent too large price decrease.Price now is unreal high. There is no race.everything is pre-planned. Slow start is over.There is still one final release,and that's it. One more pump and price go down.(because he does not hurry with the latest version) Game is over.
Hidden between all these pointless quotes I see this one post I shall quote that got missed, this seems the case from News/Market chart monitoring and the times these occurrences happen, some would say it is FUD but from all Equihash coins point of view prices are plummeting and could prove a link to why.
|
When in doubt, dig it out.
|
|
|
Jmme
Newbie
Offline
Activity: 10
Merit: 0
|
|
December 05, 2016, 04:05:34 AM |
|
It wasn't missed, it's just a bunch of shit that someone with to much time made into a conspiracy. I think President Electric Trump won the election on one of those days, maybe we can tie that to Claymore also.
|
|
|
|
melloyellow
|
|
December 05, 2016, 04:48:49 AM |
|
Here I come to try to undermine the zcash with claymore
But I crash after a few seconds
I get 180H / S per card, (rx 480)
This is what I put in the bat:
GPU_FORCE_64BIT_PTR 0 GPU_MAX_HEAP_SIZE 100 GPU_USE_SYNC_OBJECTS 1 GPU_MAX_ALLOC_PERCENT 100 GPU_SINGLE_ALLOC_PERCENT 100
ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x
Do you have an idea why this crash?
thank you in advance
On Windows you have to add set before GPU... set GPU_FORCE_64BIT_PTR 0 set GPU_MAX_HEAP_SIZE 100 set GPU_USE_SYNC_OBJECTS 1 set GPU_MAX_ALLOC_PERCENT 100 set GPU_SINGLE_ALLOC_PERCENT 100 ZecMiner64.exe -zpool zec-eu1.nanopool.org:6666 -allpools 1 -zwal my address wallet.rig -zpsw x And don't forget: Virtual memory >16 MB. ?!? set or setx is true? set modifies the current shell's (window) environment values, and the change is available immediately, but it is temporary. The change will not affect other shells that are running, and as soon as you close the shell, the new value is lost until such time as you run set again. setx modifies the value permanently, which affects all future shells, but does not modify the environment of the shells already running. You have to exit the shell and reopen it before the change will be available, but the value will remain modified until you change it again. Thanks for comprehensive answer, but I asked what is more properly used and not the differences between the set and setx? Well i use setx as global, I don't think there is a "proper" way, you either set it temporary or permanently. I guess if you have various different cards you would use set, and if they were all the same use setx. When you use setx will stay there forever. You have to go to the registry and manually remove it under currentuser\environment No you don't. Right click the start button, choose System. Click Advanced system settings. Then click Environment Variables. You can add, edit, and delete them there.
|
|
|
|
Jmme
Newbie
Offline
Activity: 10
Merit: 0
|
|
December 05, 2016, 05:11:13 AM |
|
Check the Thread Title on my post, can you also teach him to delete some of the previous quotes so it's not a waste of space
STOP WITH THE QUOTES FOOLS
|
|
|
|
melloyellow
|
|
December 05, 2016, 05:47:37 AM |
|
Check the Thread Title on my post, can you also teach him to delete some of the previous quotes so it's not a waste of space
STOP WITH THE QUOTES FOOLS
nah, I'm good
|
|
|
|
|