Antminer D3 Blissz firmware (10/12 v1.12 update)

[mohicans]

@blissz,

I did download all the firmware you posted as well as those official from Bitmain.. but now I am confused after seeing the file names.. Not sure if I have mixed the official Bitmain and yours in the same folder...

1. Antminer-D3-20171120_3-blissz.tar
2. Antminer-D3-20171121_3-blissz.tar
3. Antminer-D3-20171123_2-blissz.tar
4. Antminer-D3-20171125_0-blissz.tar
5. Antminer-D3-201709131713-0M.tar
6. Antminer-D3-201711162229-0M.tar
7. Antminer-D3-201711172221-0M.tar
8. Antminer-D3-201711182222-0M.tar

How do I know if file no 5-8 is official Bitmain's or it is also Blissz's? I am not sure if Blissz added  "blissz" in his 1st & 2nd released firmware..

Some early ones from me didn't have the blissz extension, but in filesize they were larger:
All are my firmwares, expect number 5.

Thanks Blissz... I guess that is Bitmain's official

[heythorp]

I have one rig running the 1//21 at 16GH 800W.   456 global lowest volt setting. fan auto. If i run fans less than 40% i get errors so just leave it at auto.

I have another rig that has a board issue. I have isolated that board following biitmains directions. I have now going to try your 11/25 to see if i can tweak it a bit more.

Thanks for all the work!


I should add that rig one i've had up to 20GH without a problem but I start pushing temps a little with my location. I went with power/cost/speed compromise.

[blissz]

I have one rig running the 1//21 at 16GH 800W.   456 global lowest volt setting. fan auto. If i run fans less than 40% i get errors so just leave it at auto.

I have another rig that has a board issue. I have isolated that board following biitmains directions. I have now going to try your 11/25 to see if i can tweak it a bit more.

Thanks for all the work!


I should add that rig one i've had up to 20GH without a problem but I start pushing temps a little with my location. I went with power/cost/speed compromise.

Good to hear! The last firmware should work fine on a 2 board setup. The power/cost/speed compromise is the best thing to do now I think.

[DragosD1]

I have one rig running the 1//21 at 16GH 800W.   456 global lowest volt setting. fan auto. If i run fans less than 40% i get errors so just leave it at auto.

I have another rig that has a board issue. I have isolated that board following biitmains directions. I have now going to try your 11/25 to see if i can tweak it a bit more.

Thanks for all the work!


I should add that rig one i've had up to 20GH without a problem but I start pushing temps a little with my location. I went with power/cost/speed compromise.

....isolated???

Blissz, any ideea I still can't vote?

[blissz]

I have one rig running the 1//21 at 16GH 800W.   456 global lowest volt setting. fan auto. If i run fans less than 40% i get errors so just leave it at auto.

I have another rig that has a board issue. I have isolated that board following biitmains directions. I have now going to try your 11/25 to see if i can tweak it a bit more.

Thanks for all the work!


I should add that rig one i've had up to 20GH without a problem but I start pushing temps a little with my location. I went with power/cost/speed compromise.

....isolated???

Blissz, any ideea I still can't vote?

he removed / disconnected one chain from the miner...

You should be able to vote, but you can post your preference here as well, as you like

[Huss.am]

Hi Blissz,
There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1 ? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.

[JPP1972]

I have some problem with setting frequency for single hashboard.....
https://imgur.com/gq64Rft
https://imgur.com/RxI9wFd

[SimpleCoin8]

Hi Blissz,
There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1 ? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.

Don't worry, that's your donation to Blissz for his hard work. It's working normal. You can read more about it at the beginning of the thread.

[DragosD1]

Hi Blissz,
There are two URL (dash.supernova.ca:9995)-->devFeeMiner.2 and (dash-eu.coinmine.pl:6099) --> devFeeMiner.1 ? !!!! that are running now and i have no idea what they are for as I did not write them. Also, when i go to the settings and try to remove them i can't find them. Is it something you added or you're aware of? Please take a look they are shown in the picture. It would be great if you can tell me what they are. I think there is something wrong.

You can't remove them. There are used for devfee, as specified. The way Blissz gets his bonus

[bigal82]

hey
i also have problems with frequency settings ..

no changes will aply it is stuck to 419M 

doesnt care what i choose and click on save/&apply its again at 419M

[JPP1972]

I have some problem with setting frequency for single hashboard.....
https://imgur.com/gq64Rft
https://imgur.com/RxI9wFd

I think that the chinese worker who has mounted my three D3 First batch don't like the connector #1 of my board.. he connected board 2,3,4....
i think that this is the problem... tomorrow i turn off the miner and i change the position of connector.......

[Huss.am]

Ok, so how can i make my antminer go back to its origin format?

[heythorp]

Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.


The two board unit is running at 10,700  at 560W.
475 and 437 both at lowest volt setting.
default fan

[blissz]

Ok, so how can i make my antminer go back to its origin format?

Just take the firmware file from bitmain, flash it and your miner is as it was out of the box

[may142012]

Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.


The two board unit is running at 10,700  at 560W.
475 and 437 both at lowest volt setting.
default fan

Did the defective board show any signs of "xxx" or missing any "ooo"?

[ShirouZA]

Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.


The two board unit is running at 10,700  at 560W.
475 and 437 both at lowest volt setting.
default fan

Did the defective board show any signs of "xxx" or missing any "ooo"?

My one Board showed missing 2x oo and now it has xx next to them, any ideas?

[digital$]

mine showing missing "0" and when hashing starts turns to "x"...wierd dunno if firmware related(not blissz) or actual hardware failure ie: chain scission of chips" issue

[heythorp]

Yes. I removed one board. Waiting on Bitmain to respond. My machine is under warranty.


The two board unit is running at 10,700  at 560W.
475 and 437 both at lowest volt setting.
default fan

Did the defective board show any signs of "xxx" or missing any "ooo"?

It was a long process that led to this.
At first Machine 1. that i had to remove a board from was way more stable than Machine 2 (which is now runnning perfectly).

Turned it off for the night next day started getting xxx then would stop mining all together and machine 1 would stop minning all togther.


If I set the frequency low enough on the one board. 250-300 it will show all 000 however it wont mine. Just the two other boards will. But its using power. because the chips are being fed (which is biggest reason for removal.)

I can get it to mine at default voltage at 300 for a short period then craps out the entire system. Really disappointing.

[ShirouZA]

mine showing missing "0" and when hashing starts turns to "x"...wierd dunno if firmware related(not blissz) or actual hardware failure ie: chain scission of chips" issue

Have the same issue... but even with the original firmware.

[thistlecoins]

Some more feature requests...

 - Perhaps trivial, display Temps in both C and F on the admin interface.

 - Re: ability to swap pools around easily... perhaps just a UI change to the config form... add ability to add pool rows, but also include a tickbox to enable/disable them, would at least save the copy/paste shuffle step.

 - I have some IO/GPIO ideas too, but I need to take a closer look at the beagle-board black that bitmain is using.   (Like the ability to add an ambient [intake] breakout temp sensor, and trigger shutdowns or profile changes that way too).

Fan 0 Setting...

Is my understanding correct that at this setting the firmware cares zero f*cks about what the sense cable says.  You mentioned this enables 3rd party fan mods... so is it still gonna spew 12v on two wires, but do nothing with the control and sense?  Or are you implying powering the 3rd party fans directly off the supply?

Cheers!