Zombie123
Legendary
Offline
Activity: 868
Merit: 1000
|
|
January 23, 2014, 06:13:10 PM |
|
As previously mentioned I am still pulling 440 on XFX 290's Tried everything else nothing worked
|
|
|
|
|
|
|
The grue lurks in the darkest places of the earth. Its favorite diet is adventurers, but its insatiable appetite is tempered by its fear of light. No grue has ever been seen by the light of day, and few have survived its fearsome jaws to tell the tale.
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
flyare
Newbie
Offline
Activity: 32
Merit: 0
|
|
January 24, 2014, 01:01:54 AM |
|
R9 280x from Nonny12:
cgminer.exe --scrypt -o POOL-ADDRESS -u username -p password -v 1 -w 256 -I 13 -g 2 --lookup-gap 2 --gpu-powertune -20,-20 --gpu-fan 59,50 --temp-overheat 85,85 --temp-cutoff 90,90 --gpu-memclock 1500,1500 --gpu-engine 1000,1000 --thread-concurrency 8193
I have 4 card R9 280x, only 3 card run and 1 fail. If I down --thread-concurrency 6000, them run but with big number HW. Some one help! Thanks. my miner with 4 x 280x is running with moded 3.7.2 cgminer an the following config setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 --scrypt -o server -u user -p pw -v 1 -w 256 -I 13 -g 2 --lookup-gap 2 --gpu-powertune -20 --gpu-engine 1020 --gpu-memclock 1600 --thread-concurrency 8191 3 x 350 kh/s 1 x 230 kh/s (monitor conect on this device) no rejects hw errors 0.01% no problem i think i'm using 4gb of mem if you have more u maybe need to tweak my settings good luck Hi gonzzo My system: Cpu: 3.0 Celeron, Ram 4G, 4xCard Asus R9 280x. I still have problem 3x350 Khz/s 1xoff Khz/s
|
|
|
|
gonzzo
|
|
January 24, 2014, 05:23:58 AM |
|
R9 280x from Nonny12:
cgminer.exe --scrypt -o POOL-ADDRESS -u username -p password -v 1 -w 256 -I 13 -g 2 --lookup-gap 2 --gpu-powertune -20,-20 --gpu-fan 59,50 --temp-overheat 85,85 --temp-cutoff 90,90 --gpu-memclock 1500,1500 --gpu-engine 1000,1000 --thread-concurrency 8193
I have 4 card R9 280x, only 3 card run and 1 fail. If I down --thread-concurrency 6000, them run but with big number HW. Some one help! Thanks. my miner with 4 x 280x is running with moded 3.7.2 cgminer an the following config setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 --scrypt -o server -u user -p pw -v 1 -w 256 -I 13 -g 2 --lookup-gap 2 --gpu-powertune -20 --gpu-engine 1020 --gpu-memclock 1600 --thread-concurrency 8191 3 x 350 kh/s 1 x 230 kh/s (monitor conect on this device) no rejects hw errors 0.01% no problem i think i'm using 4gb of mem if you have more u maybe need to tweak my settings good luck Hi gonzzo My system: Cpu: 3.0 Celeron, Ram 4G, 4xCard Asus R9 280x. I still have problem 3x350 Khz/s 1xoff Khz/s which miner and os do u use ? at the moment i have 4 x 355 kh/s, moded cgminer 3.7.2 config: setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 cgminer --scrypt -o server -u user -p pw -v 1 -I 13 -w 256 -g 2 --lookup-gap 2 --gpu-powertune -20 --gpu-engine 1000 --gpu-memclock 1500 --thread-concurrency 8193 --no-submit-stale while experimenting yesterday on a other worker with 3 x 280x i had some problems with devices going off, after a reboot the problem was solved (same config) not sure what it was
|
|
|
|
fantaza
Newbie
Offline
Activity: 5
Merit: 0
|
|
January 24, 2014, 01:16:14 PM |
|
I am running 3 r280x OC and 3 r280x VaporX with the following config -g 2 -I 13 -w 256 --thread-concurrency 8921 --gpu-engine 1050 --gpu-memclock 1500 --gpu-powertune -20 --lookup-gap 2 After some testing, the funny thing is the 3 r280x OC are giving me 370+ Kh/s each but the 3 r280x VaporX only give me 270+ kh/s each For other scrypt coin both type of card give me ard 725kh/s each. http://i1318.photobucket.com/albums/t659/francisckf/vertcoin_zps8afc3bc1.jpgAnyone using r280x VaporX have any idea?
|
|
|
|
minero1
|
|
January 24, 2014, 02:48:59 PM |
|
2X 7950; I 13 -g 2 -w 256 --thread-concurrency 6912 --gpu-engine 1100 --gpu-memclock 1575 :: 295KH/s 1X 6970; I 19 -g 2 -w 256 --thread-concurrency 6400 --gpu-engine 900 --gpu-memclock 1375 :: 245KH/s 6950 unlocked; I 13 -g 2 -w 256 --thread-concurrency 2786 --gpu-engine 900 --gpu-memclock 1250 :: 150KH/s no HWs WTF???
|
|
|
|
gonzzo
|
|
January 24, 2014, 03:06:05 PM Last edit: January 24, 2014, 04:57:21 PM by gonzzo |
|
I am running 3 r280x OC and 3 r280x VaporX with the following config -g 2 -I 13 -w 256 --thread-concurrency 8921 --gpu-engine 1050 --gpu-memclock 1500 --gpu-powertune -20 --lookup-gap 2 After some testing, the funny thing is the 3 r280x OC are giving me 370+ Kh/s each but the 3 r280x VaporX only give me 270+ kh/s each For other scrypt coin both type of card give me ard 725kh/s each. Anyone using r280x VaporX have any idea? are u using cgwatcher? had the same problem while using cg, problem was solved after throwing away cg and using standalone .cmd scripts and don't forget the setx commands!
|
|
|
|
mik_druid
|
|
January 24, 2014, 04:56:28 PM |
|
For my r9 270 I'm using --scrypt -I 13 -g 2 -w 256 --thread-concurrency 2000 --gpu-powertune 0 the other confing simply doesn't work. I mine 200 Kh according to cg miner but 50Kh according to pool ( i'm mining 20+ hours) I can mine max 2 Vertcoins a day
|
|
|
|
madjihad
|
|
January 24, 2014, 05:40:56 PM |
|
For my r9 270 I'm using --scrypt -I 13 -g 2 -w 256 --thread-concurrency 2000 --gpu-powertune 0 the other confing simply doesn't work. I mine 200 Kh according to cg miner but 50Kh according to pool ( i'm mining 20+ hours) I can mine max 2 Vertcoins a day Windows or Linux? Under linux I've finally managed to get 170kh with 7870 which is basically R9 270: -I 12 -w 256 -g 2 -v 1 --thread-concurrency auto --lookup-gap 2 --gpu-engine 1100 --gpu-memclock 1250 And to check you real hashrate instead of pool's dashboard you can use WU in your miner
|
|
|
|
mik_druid
|
|
January 24, 2014, 06:11:51 PM |
|
windows , I'll check your settings [ unfortunatelly they dont's work ] I've got WU 40.1/m ( what is WU? Sorry I'm new in this stuff) Grr I'd rather mine doge instead
|
|
|
|
madjihad
|
|
January 24, 2014, 08:03:45 PM |
|
windows , I'll check your settings [ unfortunatelly they dont's work ] Try -I 12 -w 256 -g 2 -v 1 --thread-concurrency 8000 --lookup-gap 2 --gpu-engine YOUR_CARD_DEFAULT_CORE_CLOCK --gpu-memclock YOUR_CARD_DEFAULT_MEMCLOCK_CLOCK Or just -I 12 -w 256 -g 2 -v 1 --thread-concurrency 8000 --lookup-gap 2 --gpu-engine 800 --gpu-memclock 1000 Works on Windows 7 x64 for me (Driver 13.9) I've got WU 40.1/m ( what is WU? Sorry I'm new in this stuff)
WU - that's the Work Utility, defined as the number of diff1 shares work / minute (accepted or rejected). Sow very roughly it's you hashrate after exclution of HW. But including any other rejections. Grr I'd rather mine doge instead Nooooo.... Don't give up with Vertcoin, I've played with config a week, from diff 0.6 And if you decide to go for DOGE, better go for Skeincoin than
|
|
|
|
zoro
|
|
January 24, 2014, 08:11:10 PM Last edit: January 24, 2014, 09:49:45 PM by zoro |
|
guys, have you noticed something strange with cgminer? evry time i start cgminer i see a lot of accepted shares by each vga /minute. after a day, the rate of accepted shares is reduced alot (lets say 1/min!!!) then i restart cgminer and i see again a lot shares/minute! wtf is going on? i use the same pool, hashrate is always the same as WU value too! am i missing something? edit: i think i get it. the diff of each share is increasing automatically and they are fewer as time goes by. no problem
|
|
|
|
mik_druid
|
|
January 24, 2014, 10:59:31 PM |
|
windows , I'll check your settings [ unfortunatelly they dont's work ] Try -I 12 -w 256 -g 2 -v 1 --thread-concurrency 8000 --lookup-gap 2 --gpu-engine YOUR_CARD_DEFAULT_CORE_CLOCK --gpu-memclock YOUR_CARD_DEFAULT_MEMCLOCK_CLOCK Or just -I 12 -w 256 -g 2 -v 1 --thread-concurrency 8000 --lookup-gap 2 --gpu-engine 800 --gpu-memclock 1000 Works on Windows 7 x64 for me (Driver 13.9) I've got WU 40.1/m ( what is WU? Sorry I'm new in this stuff)
WU - that's the Work Utility, defined as the number of diff1 shares work / minute (accepted or rejected). Sow very roughly it's you hashrate after exclution of HW. But including any other rejections. Grr I'd rather mine doge instead Nooooo.... Don't give up with Vertcoin, I've played with config a week, from diff 0.6 And if you decide to go for DOGE, better go for Skeincoin than I set mine r9 270: " -I 12 -w 256 -g 2 -v 1 --thread-concurrency 8000 --lookup-gap 2 --gpu-engine 975 --gpu-memclock 1400" only 14KH but UW equals the speed , what am I doing wrong?
|
|
|
|
SlyFecker
Newbie
Offline
Activity: 4
Merit: 0
|
|
January 24, 2014, 11:07:36 PM |
|
1 x Saphire Toxic 280x with CGMiner running @ 410K
setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 cgminer.exe --scrypt -o stratum+tcp://s.eu.vertcoin.org:3333 -u xxxx -p xxxxx -g 2 -w 256 -I 13 --thread-concurrency=8250 --gpu-engine=1160 --gpu-memclock=1860 --auto-fan --gpu-powertune 20
|
|
|
|
mik_druid
|
|
January 24, 2014, 11:20:54 PM |
|
1 x Saphire Toxic 280x with CGMiner running @ 410K
setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 cgminer.exe --scrypt -o stratum+tcp://s.eu.vertcoin.org:3333 -u xxxx -p xxxxx -g 2 -w 256 -I 13 --thread-concurrency=8250 --gpu-engine=1160 --gpu-memclock=1860 --auto-fan --gpu-powertune 20
Ok I managed somehow to achieve decent speed 180KH on my 270 -I 12 -w 256 -g 2 -v 1 --thread-concurrency 4648 --lookup-gap 2 --gpu-engine 1050 --gpu-memclock 1500 I had to change thread concurrency to around 4000 , thanks for help Is there any way to make it work faster?
|
|
|
|
SlyFecker
Newbie
Offline
Activity: 4
Merit: 0
|
|
January 24, 2014, 11:27:12 PM |
|
1 x Saphire Toxic 280x with CGMiner running @ 410K
setx GPU_MAX_ALLOC_PERCENT 100 setx GPU_USE_SYNC_OBJECTS 1 cgminer.exe --scrypt -o stratum+tcp://s.eu.vertcoin.org:3333 -u xxxx -p xxxxx -g 2 -w 256 -I 13 --thread-concurrency=8250 --gpu-engine=1160 --gpu-memclock=1860 --auto-fan --gpu-powertune 20
Ok I managed somehow to achieve decent speed 180KH on my 270 -I 12 -w 256 -g 2 -v 1 --thread-concurrency 4648 --lookup-gap 2 --gpu-engine 1050 --gpu-memclock 1500 I had to change thread concurrency to around 4000 , thanks for help Is there any way to make it work faster? Your on the 270 so - up your thread-concurrency to 8192 (-/+20). Save a copy of your .bat file and play with the numbers, gradually upping them until you get the best out of your card. Down -12 to 11 (until you get higher speeds then change +1 each try) Good Luck x
|
|
|
|
b0ss
Newbie
Offline
Activity: 53
Merit: 0
|
|
January 24, 2014, 11:32:49 PM Last edit: January 25, 2014, 02:19:17 AM by b0ss |
|
I'm getting 600+KH/s with 1xHD7950 from PowerColor and 2 HD5850 DCU2 cards from Asus. They're getting this hot because they're sandiwched, I don't have risers atm. Here is my BAT: cgminer.exe --scrypt -o pooladdress.com:port -u username --gpu-map 0:1,1:0,2:2 -p password --gpu-engine 820,1100,820 --gpu-memclock 1150,1500,1150 -g 2 --thread-concurrency 5120,19712,5120 -I 15,18,18 -w 256 --gpu-powertune 10 --gpu-fan 50-90,90-100,50-90 The HD7950 card does run at 1.250v (others are stock) because somehow it's hardlocked by PowerColor, so it gets way too hot and burns a lot of power... https://i.imgur.com/zfrcun8.pngEDIT: Just noticed the HD7950 goes sick after some time, running it at -I 18 solves the problem, still gets over 600KH/s avg in total. I edited the above BAT config to avoid confusion but the screenshot still shows 20.
|
|
|
|
mik_druid
|
|
January 24, 2014, 11:49:46 PM |
|
For r9 270 Any ideas? I got only 170 KH
-I 20 -g 1 --gpu-memclock 1500 --gpu-engine 1100 --thread-concurrency 14208gives me ~215 Kh/s hehe 0000KH with my card
|
|
|
|
fantaza
Newbie
Offline
Activity: 5
Merit: 0
|
|
January 25, 2014, 12:59:15 AM |
|
are u using cgwatcher? had the same problem while using cg, problem was solved after throwing away cg and using standalone .cmd scripts and don't forget the setx commands!
I am using cgminer. Any experience on this.
|
|
|
|
amachiavellian
Newbie
Offline
Activity: 15
Merit: 0
|
|
January 25, 2014, 01:17:13 AM Last edit: January 25, 2014, 02:38:12 AM by amachiavellian |
|
edit: got it. i just took the short bus ...
|
|
|
|
minecrew
Full Member
Offline
Activity: 224
Merit: 100
MineCrew
|
|
January 25, 2014, 02:33:00 AM |
|
Mining Vertcoin I'm getting just around 75KHS w/ vertminer v0.5.2 and with Vertcoin-CGMinerAleksNR3 I get a blazing 10KHS.
Try to adjust intensity and thread-concurrency, set it lower. You should have about 100 MH/s maximum at your card.
|
|
|
|
|