[ANN] sgminer with X11/X13/Nist5/Quark/Anime kernels compatible 14.6 amd drivers

[nfox]

I need config for r9 290x and 7950 

[kozmos]

This is the download link for the fixed miner: https://mega.co.nz/#!ZsJTALQI!qDh9jCWULjabTDPYq0K4fZamdZrPwot7m7AAfTEOJPQ

Download link is dead now.

New Link: https://mega.co.nz/#!8gZ3BbBa!tJLKAr08Lirinh39h55naOY20gLbyPcQpBgWWcB3UDA

[hashbrown9000]

The miner has been running on my test rig now for 2.5 hours.  It has one Gigabyte WF 270 non X and three Sapphire 270x cards.  The Gigabyte is undervolted to 1.075 volts and the 3 Sapphires are undervolted to 1.100 volts.  Engine clocks down just a bit to find stability.

Running BAMT 1.6.0 upgraded to the 14.6 beta drivers, using this procedure:

http://www.reddit.com/r/BAMT/comments/28xu3i/add_amd_146_drivers_and_djm34s_optimized_sgminer/

Config:

{
"pools" : [
   {
      "url" : "x",
      "user" : "x",
      "pass" : "x"
   }
],
"xintensity" : "512",
"kernel" : "x11mod",
"lookup-gap" : "2",
"shaders" : "1280",
"worksize" : "128",
"gpu-threads" : "2",
"gpu-engine" : "1050",
"gpu-fan" : "20-85",
"gpu-memclock" : "1250",
"gpu-powertune" : "20",

"temp-cutoff" : "92",
"temp-overheat" : "89",
"temp-target" : "75",

"api-listen": true,
"api-port": "4028",
"api-allow": "W:127.0.0.1",
"api-mcast-port" : "4028",
"auto-fan" : true,
"expiry" : "1",
"failover-only" : true,
"log" : "5",
"queue" : "0",
"scan-time" : "1",
"temp-hysteresis" : "3",

"failover-switch-delay" : "30",
"no-pool-disable" : true,
"kernel-path" : "/usr/local/bin"
}


Each one hits 2.55 MH/s

[scrubadub]

Has anyone checked for any hidden hash redirect?

netstat -tulpan
and
tcpdump -n -i eth0 port not 22

both look ok for me.

Of course they could've patched both of those programs but that's a lot of extra work. Feel free to throw a hub inline and sniff from another computer if you're worried about that.

And you have no reason to trust me so check those yourself.

[Vampiro4L]

Tips sent to OP and the_g00se for the bamt install instructions.
If you found this thread helpful tip these guys they were nice enough to share this stuff with the community.

[fra55]

Anyone with the same problem?

Miner keeps to put GPUs in idle performance claiming that no work is available from pools...after a few seconds it will state "Work available, resuming" and so on until I shut the miner off.
Strange to say, it's actually mining as the pool shows the correct hashrate...

[bullus]

Which driver should I use for 5gpu and windows7 64bit to get the boost with 14.6 files/drivers? (7950's)
With 14.4 drivers I can't install the drivers for the fith one, get a explanation icon.

[portron]

I've posted a guide on how to update PiMP to use this, thanks so much for the great work guys.

http://www.reddit.com/r/getpimp/comments/294uie/add_amd_146_drivers_and_djm34s_optimized_sgminer/

[Mylo]

New 14.6 drivers cause ~ +10*C (290) temp increase. What's the point? X11 coins were made to work fine under 80*C at 30*C+ ambient in Summer.
Now we draw more electricity, overwhelm cards just like before with Scrypt.

The most optimal solution is to have stable drivers + extracted AMD dll's, minus 0.3-0.4Mh (280x-290)

[bengx]

Hai guys, is anybody already setup mining vertcoin with this ?

You can try mining on x11.greenpool.com. Mines x11 coins and autoconverts to Vertcoins.

[Burninj]

Djm34 would you have the skill to make a bitblock gpu miner?

[masonbtc]

Anyone else getting this error in sgminer?

Getaddrinfo() in setup_Stratum_socket() returned 10109: The specified class was not found

[fran2k]

New 14.6 drivers cause ~ +10*C (290) temp increase. What's the point? X11 coins were made to work fine under 80*C at 30*C+ ambient in Summer.
Now we draw more electricity, overwhelm cards just like before with Scrypt.

The most optimal solution is to have stable drivers + extracted AMD dll's, minus 0.3-0.4Mh (280x-290)

Jajaja man. Thanks for the laught.

14.6 drivers increased the hashrate around 30-50%, obviously also increased the power consumption.

[djm34]

Anyone else getting this error in sgminer?

Getaddrinfo() in setup_Stratum_socket() returned 10109: The specified class was not found

Can you give a little more detail in which occasion you had this error ?

[masonbtc]

https://i.imgur.com/cXRd2BS.jpg

It just pops up every 5 - 10 seconds in sgminer.  I can't tell if it is affecting anything at all.  Also when loading up sgminer it says something about failed to resolve pool.  As far as I can tell it is connecting though?

[masonbtc]

oh i might have figured it out...  .conf file wasn't updated...

edit:
ya that fixed it..  I normally just pass pool info and everything to sgminer via a batch file, but I updated the .conf file with all of that info and that fixed the error.

[daeminium]

Anyone with the same problem?

Miner keeps to put GPUs in idle performance claiming that no work is available from pools...after a few seconds it will state "Work available, resuming" and so on until I shut the miner off.
Strange to say, it's actually mining as the pool shows the correct hashrate...

x2 same here :-(

[djm34]

Anyone with the same problem?

Miner keeps to put GPUs in idle performance claiming that no work is available from pools...after a few seconds it will state "Work available, resuming" and so on until I shut the miner off.
Strange to say, it's actually mining as the pool shows the correct hashrate...

x2 same here :-(

Use the latest binary I added to the thread, there shouldn't be any problem

[coinjohn]

it would be great if someone added a pre-compiled version for windows containing the opencl files and bin files for all the latest amd cards

p.s. i tried in so many ways to run my r9 290 (non x) on windows 8.1 following what i read here but for starters i'm a noob and the best result i got so far was seeing the hashrate go to 4.2mh/s but i wasn't getting any work from the pools and i was seeing HW errors, so i decided to roll back to my older drivers and wait for a revised or easier to run version for windows.

[aznboy84]

it would be great if someone added a pre-compiled version for windows containing the opencl files and bin files for all the latest amd cards

p.s. i tried in so many ways to run my r9 290 (non x) on windows 8.1 following what i read here but for starters i'm a noob and the best result i got so far was seeing the hashrate go to 4.2mh/s but i wasn't getting any work from the pools and i was seeing HW errors, so i decided to roll back to my older drivers and wait for a revised or easier to run version for windows.

try this one ....
https://bitcointalk.org/index.php?topic=658975.0