|
blissz (OP)
|
 |
November 28, 2017, 12:51:38 PM |
|
Hi Blissz! Thank you for your job.
Do you recommend fan mod?
If I chang fan quieter than original?
And I want to report Miner Status by email.
Thanks.
You're welcome  If you run it at the lowest voltage and the ambient temperatures are quite low I advice to replace the fans as there are quite some fans a lot less noisy compared to the original ones |
|
|
|
|
|
|
|
|
|
|
|
|
|
You get merit points when someone likes your post enough to give you some. And for every 2 merit points you receive, you can send 1 merit point to someone else!
|
|
|
Advertised sites are not endorsed by the Bitcoin Forum. They may be unsafe, untrustworthy, or illegal in your jurisdiction.
|
|
|
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 12:55:32 PM |
|
Currently testing the next version. It cointains a fix for the restart on low hashrate detection + it includes an upgrade from cgminer 4.9 to cgminer 4.10
|
|
|
|
|
mohicans
Newbie
 Offline
Activity: 21
Merit: 0
|
|
November 28, 2017, 01:01:46 PM |
|
Currently testing the next version. It cointains a fix for the restart on low hashrate detection + it includes an upgrade from cgminer 4.9 to cgminer 4.10
I hope we still have the option to use or not to use the auto restart. I am using Awesomeminer for that already. BTW,, 2 x D3 is now on the latest firmware mod. both at 16.15Ghs @ 830W |
|
|
|
|
|
dndssc
|
|
November 28, 2017, 01:06:16 PM |
|
Currently testing the next version. It cointains a fix for the restart on low hashrate detection + it includes an upgrade from cgminer 4.9 to cgminer 4.10
very interesting, cgminer 4.10 works better? high hashrate? thanks! |
|
|
|
mahouneko
Member
Offline
Activity: 93
Merit: 10
|
|
November 28, 2017, 01:35:43 PM |
|
Hi Blissz! Thank you for your job.
Do you recommend fan mod?
If I chang fan quieter than original?
And I want to report Miner Status by email.
Thanks.
You're welcome If you run it at the lowest voltage and the ambient temperatures are quite low I advice to replace the fans as there are quite some fans a lot less noisy compared to the original ones Thank for your answer. I will try it. The Ambient temperatures is getting cold. |
|
|
|
dashcoin1
Newbie
Offline
Activity: 27
Merit: 0
|
|
November 28, 2017, 01:42:45 PM |
|
I need you help!
After I updated the software to dig other coins, mine machine crashed can not log in!
|
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 01:49:08 PM |
|
I need you help!
After I updated the software to dig other coins, mine machine crashed can not log in!
hmmz sounds like you didn't flash my firmware. (as you can only mine x11 with mine...) For rescue mode: flash this image on a micro sd card (I used win32diskimager) and put that in your d3 controller board https://shop.bitmain.com/support.htm?pid=007201604120945219855QObfk20066Cthen flash again after it booted and remove the sd card again |
|
|
|
|
dashcoin1
Newbie
Offline
Activity: 27
Merit: 0
|
|
November 28, 2017, 01:52:33 PM |
|
I need you help!
After I updated the software to dig other coins, mine machine crashed can not log in!
D3 only can dig dash? D3 only can dig dash?i'm flashed your firmware ,changed to dig onixcoin.it's can not log in [/quote] |
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 02:34:29 PM |
|
I need you help!
After I updated the software to dig other coins, mine machine crashed can not log in!
D3 only can dig dash? D3 only can dig dash?i'm flashed your firmware ,changed to dig onixcoin.it's can not log in [/quote] Every x11 coin should work. Seems like you had a bad flash for some reason. Please make sure to download the firmware again and try the recovery method as posted. |
|
|
|
|
silvioraof
Newbie
Offline
Activity: 16
Merit: 0
|
|
November 28, 2017, 04:01:08 PM |
|
With this firmware ...does anyone tried to use a different PSU ?? Less than 1600 w?
Could I use a 1200 or 1k ?
im using a 1000watt for mine At the lowest voltage setting at ~15 / 16GH/s/s you can run it at 750watt - 800watt. So my advice would be to have at least a 900+ watt power supply for this. Make sure not to connect al boards as you're still on the stock firmware, otherwise you'll blow the PSU. First flash it / set it to the lowest voltage / 400Mhz and then connect all the boards. Thanks blissz u r the guy ...thanks for being here too. |
|
|
|
|
stalin12
Newbie
Offline
Activity: 3
Merit: 0
|
|
November 28, 2017, 06:54:35 PM |
|
Hey Blissz
Can you do a change from pool to pool without rebooting?
|
|
|
|
|
crackfoo
Legendary
Offline
Activity: 3458
Merit: 1126
|
|
November 28, 2017, 07:27:10 PM |
|
Hey Blissz
Can you do a change from pool to pool without rebooting?
changing pools/order doesn't reboot, just restarts cgminer |
ZPOOL - the miners multipool! Support We pay 10 FLUX Parallel Assets (PA) directly to block rewards! Get paid more and faster. No PA fee's or waiting around for them, paid instantly on every block found!
|
|
|
ShirouZA
Member
Offline
Activity: 126
Merit: 10
|
|
November 28, 2017, 07:47:17 PM |
|
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
|
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 07:51:35 PM |
|
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
It probably shows hardware errors too on that chain? I think it's clocked to high for the amount of voltage set. |
|
|
|
|
ShirouZA
Member
Offline
Activity: 126
Merit: 10
|
|
November 28, 2017, 08:06:30 PM |
|
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
It probably shows hardware errors too on that chain? I think it's clocked to high for the amount of voltage set. It does show a lot of hardware errors, but I've even had it on 100M and the lowest Volt settings.. tried several options and still it shows 0000... If I am lucky and reboot it works for few seconds to hash and then goes back to 0000 Hash Rates. If I flash back to the Bitmain firmware it works fine though? |
|
|
|
|
zerocom
Legendary
Offline
Activity: 1134
Merit: 1003
|
|
November 28, 2017, 08:16:03 PM |
|
Hello blissz I've read a few posts and see you do a great job, I wanted to ask you there will be a chance to add new algorithms? or change from x11 to scrypt?
can you put a switch to change pools like in the baikal and add some of the others? thanks and sorry for my english.
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 08:19:31 PM |
|
v1.0 :: 28/11 :: RECOMMENDED UPDATEDownload:https://mega.nz/#!rgR1RCpS!aoBjx2kZduOS23KFzS_0jUHhw4-SWfs23BYLL2SZJC8Changes 28/11:- Fixed the automatic reboot on low hashrate or high ASIC fail rate. - updated cgminer to v4.10 (for details see: https://bitcointalk.org/index.php?topic=28402.msg17594456#msg17594456) - improved pool switching behavior - improved startup stability of all chains - cgminer binary optimizations
know issues:- switching pools can sometimes cause the miner to wait for work for ~5 seconds. (improved from ~10 seconds) - loosing network connection doesn't stop the mining boards properly (this is default bitmain behavior, but I don't like it, so it will be changed in the future) happy mining!
|
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 08:22:56 PM |
|
Anyone else having problems with one of their chains just showing no Hash Rates? just shows 0000
It probably shows hardware errors too on that chain? I think it's clocked to high for the amount of voltage set. It does show a lot of hardware errors, but I've even had it on 100M and the lowest Volt settings.. tried several options and still it shows 0000... If I am lucky and reboot it works for few seconds to hash and then goes back to 0000 Hash Rates. If I flash back to the Bitmain firmware it works fine though? That board needs more voltage I guess. Just set the voltage for that board a bit higher. Make sure to flash the firmware I just posted. It might help as well |
|
|
|
|
may142012
Member
Offline
Activity: 301
Merit: 10
|
|
November 28, 2017, 08:27:59 PM |
|
Some questions Blissz, is your latest firmware supporting extranonce.subscribe? You know the #xnsub at the end.
What causes loosing network connection?
|
|
|
|
|
|
blissz (OP)
|
|
November 28, 2017, 08:35:41 PM |
|
Some questions Blissz, is your latest firmware supporting extranonce.subscribe? You know the #xnsub at the end.
What causes loosing network connection?
I checked the code it does an extranonce_subscribe_stratum(pool), so support is there. Loosing network for a long time (i.e. disconnect the cable) for more then 2 minutes doesn't shut off the miner currently. This makes sense for the long bitcoin block times maybe, but not for mining most of the x11 coins as their block times are short. I do want to change this or make it optional, to temporary shut off the mining boards until the network connection gets back. |
|
|
|
|
|
Poll
