Antminer D3 Blissz firmware (10/12 v1.12 update)

[5uicid]

Hi blissz,

the "Automatic Reboot on low hashrate or high ASIC fail" is restarting my D3 every 60 minutes.
It is possible to create a logfile over more times as 1 reboot?

The kernel log is without every error messages.

[miningag]

Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?

Cheers W_M

around 1250W

Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w

wich settings do you use for the 20GH/s at 1100W?

@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
and i have not always the same GH/s on every startup (it changes around 1Gh/s) sometimes i have 18ghs and sometimes 19ghs/s with the same settings (always the same power consumtion) has anyone the same result?

great job blissz!

[Marvell2]

Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?

Cheers W_M

around 1250W

Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w

wich settings do you use for the 20GH/s at 1100W?

@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!

20GH at 1100 watts is impressive is this with factory firmware ?

[JimmyFish]

Maybe I have set diff level too high, I have been trying d=32000.

Where I can change this value?

Hi, in the password field you just add d=40 for a diff of 40.

So mine is c=DASH,d=80 in the password field.

This is for zpool.ca, other pools may do it in a different way.

[Sjouk]

Hi!

I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.

Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.

I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!

I'm begining to enter in panic! Could somebody help me with that? What should I do?

I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.

By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.

Thanks in advance.

BLISSZ  .....

Can you please help us....
There are many more  who did this....;(   

Please give us a hand...

[microtechies]

Hi!

I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.

Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.

I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!

I'm begining to enter in panic! Could somebody help me with that? What should I do?

I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.

By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.

Thanks in advance.

BLISSZ  .....

Can you please help us....
There are many more  who did this....;(   

Please give us a hand...

Bitmain sent me a replacement control board for free. Even thought I said it was my mistake and put the wrong firmware on it. From opening of ticket to delivery it was 7 days to the UK. Not bad shame the rest of the business couldn't be that smooth

[xefe]

What is the maximum hashrate you can achieve with stability on a 19.3 model? My aim is for maximum hashrate and not efficiency, but don't want to risk burning a board since its working full time. Temps are stable now at 70c with 19.3.

Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency

Thanks

[microtechies]

What is the maximum hashrate you can achieve with stability on a 19.3 model? My aim is for maximum hashrate and not efficiency, but don't want to risk burning a board since its working full time. Temps are stable now at 70c with 19.3.

Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency

Thanks

I've been getting about 22-23g but Nicehash sometimes reports up to 28g

[cryptonitro]

Hi!

I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.

Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.

I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!

I'm begining to enter in panic! Could somebody help me with that? What should I do?

I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.

By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.

Thanks in advance.

BLISSZ  .....

Can you please help us....
There are many more  who did this....;(    

Please give us a hand...

Bitmain sent me a replacement control board for free. Even thought I said it was my mistake and put the wrong firmware on it. From opening of ticket to delivery it was 7 days to the UK. Not bad shame the rest of the business couldn't be that smooth

control board will not change nothing , i try with an other one , hashboards are fail , i ever told taht

@Blissz please answer to mp

[micairvas]

What is best miner hashing/setup for 950w power consumption? Can I get 17-18ghs on 950w?

[microtechies]

Why doesn't Blissz make a firmware for the L3+?

I'm sure he will but he is busy perfecting the D3 for now

[crackfoo]

Why doesn't Blissz make a firmware for the L3+?

he doesn't have an L3+. Send him one and I'm sure he'll bang off some new firmware.

[alko67bi]

Maybe I have set diff level too high, I have been trying d=32000.

Where I can change this value?

Hi, in the password field you just add d=40 for a diff of 40.

So mine is c=DASH,d=80 in the password field.

This is for zpool.ca, other pools may do it in a different way.

Thanks, but I use antpool.

[funminer]

What is the maximum hashrate you can achieve with stability on a 19.3 model? My aim is for maximum hashrate and not efficiency, but don't want to risk burning a board since its working full time. Temps are stable now at 70c with 19.3.

Just want to know if its worth putting this firmware and overclock, as from what i see is more foccused in efficiency

Thanks

I've been getting about 22-23g but Nicehash sometimes reports up to 28g

The Firmware is goog for both, efficiency or max Hashrate, because you can get out the max from every hashboard and you must not stop because one board get to hot, take only care that your chips not get to hot.

[dlezama]

Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?

Cheers W_M

around 1250W

Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w

wich settings do you use for the 20GH/s at 1100W?

@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!

20GH at 1100 watts is impressive is this with factory firmware ?

No, with Blissz firmware of course These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errors

[hardworker27]

Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?

Cheers W_M

around 1250W

Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w

wich settings do you use for the 20GH/s at 1100W?

@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!

20GH at 1100 watts is impressive is this with factory firmware ?

No, with Blissz firmware of course These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errors

https://imgur.com/JiZz4to.jpg
https://imgur.com/y8GctAY.jpg

How about your fan speeds to get that temp? Thanks.

[dlezama]

Hi, what is the power consumption of 19.3 Model (Nov.batch) at 15Ghs hashrate?

Cheers W_M

around 1250W

Are you sure? Mine is October batch (19_3 model) and factory settings it was at 17GH/s and 1050w. Now I've tweaked it to 20GH/s at 1100w

wich settings do you use for the 20GH/s at 1100W?

@blissz i have seen when the first pool is down it stucks on the dev fee pool!
is it maybe possible to push a little bit the Auto fan performance settings to a little bit higher rpm? (it would be nice a little bit more power)
great job blissz!

20GH at 1100 watts is impressive is this with factory firmware ?

No, with Blissz firmware of course These are my settings but each miner (and board) is different, you have to tweak until you see good temperature and HW errors

How about your fan speeds to get that temp? Thanks.

Right there in the pic (I'm having some issues linking pics here, but my original post has the links). Temps around 70C, fans go between 3500 and 4000, but this is in a quite cool room (about 50F). Once I move it to my garage where I have more challenges cooling things down I may need to dial this back a little.

EDIT: Oh, and I have the fan in "AUTO performance"

[dganm]

Hi!

I installed Blissz firmware in my d3's and I made a mistake copying the cgminer archive from /usr/bin from one of the d3 to an l3+ I have too.

Of course it started up in the l3+ with the --scrypt param but it didn't mine anything.

I flashed my l3+ to stock again but now it doesn't recognize any of the chains on my l3+!

I'm begining to enter in panic! Could somebody help me with that? What should I do?

I think is because some additional files created or some script running in parallel with cgminer. I don't know really but that file is the only I changed "trying to not touch the filesystem" :S.

By the way, Is there any plan to make a firmware for l3's? It would be nice! on d3's are running amazing.

Thanks in advance.

BLISSZ  .....

Can you please help us....
There are many more  who did this....;(   

Please give us a hand...

Bitmain sent me a replacement control board for free. Even thought I said it was my mistake and put the wrong firmware on it. From opening of ticket to delivery it was 7 days to the UK. Not bad shame the rest of the business couldn't be that smooth

Thank you for your response. I'm going to open a ticket with bitmain then.

Regards!

[micairvas]

"Lowest" voltage is value 1, right? I tried lowest voltage and 412mhz clock and works. Can lowest value can work with higher clock, for example 450mhz?
Why blissz wrote lowest voltage on 400mhs, when clock can bi higher?

[micairvas]

Also if still happens that some board go dead. Blissz should work on last Bitmain FW, I got this FW from Bitmain 7 days ago, and after that all miners works perfect, no more dead boards after some time.

Link for Bitmain lastest bios:
https://shop.bitmain.com/support.htm?pid=00720170915192851224mJ36J1ap066E