ANTMINER S3+ Discussion and Support Thread

[bruno033]

Bitmain's site has the firmware:
https://www.bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O0633

I use Cygwin to ssh into them then use vi editor.
U can also download putty to ssh in.

If the new FW is loaded into the S3, does the full range of clocks become available through the "Miner configuration"/"Advanced" menu?

http://img4.hostingpics.net/pics/177521Sanstitre.png

[1714615238]

1714615238

[TrevorS]

Thanks guys, much appreciated!  And congrats on successfully updating your version of CGminer, Bruno!  

[bruno033]

thank you, is I'm glad to find people who helped me

[TrevorS]

thank you, is I'm glad to find people who helped me

PS. Your English is one hell of a lot better than my French, please don't feel at all apologetic!  Best regards, dude!  

[Stratobitz]

Launched 52 S3+ Units today!  Out of the 52 only 1 gave us low hashrate issues. May just be a glitch, planning to reset and configure again tomorrow to see if it corrects itself. Just to tired to play with tonight.

A few are actually hashing near/above 700 GHash.

Job well done BitMainTech! I think youve cornered the market!

Strato

[Stratobitz]

Has anyone tried manually setting the frequency higher than 250?  If the Ants were kept in a cold server room at 58 Degrees, would that perhaps allow higher hashrates?

Strato

[notlist3d]

Ok, so since I formatted my hdd in my laptop like two weeks ago. I lost some of my favorite links.

Can someone post me a ink on the new firmware I have with the stuff to edit so I can get 243.75 added back in. I think it was removed when this (the S3) got reset.

Ty.

Bitmain's site has the firmware:
https://www.bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O0633

I use Cygwin to ssh into them then use vi editor.
U can also download putty to ssh in.

Sorry for totally stupid question i just have not done it.  To upgrade do i just  use the "Flash new firmware image"?  Is that used for upgrade in image?

Thanks for any help.

[MiningBuddy]

Launched 52 S3+ Units today!  Out of the 52 only 1 gave us low hashrate issues. May just be a glitch, planning to reset and configure again tomorrow to see if it corrects itself. Just to tired to play with tonight.

A few are actually hashing near/above 700 GHash.

Job well done BitMainTech! I think youve cornered the market!

Strato

What do you have them clocked at to achieve near 700?

[Stratobitz]

Launched 52 S3+ Units today!  Out of the 52 only 1 gave us low hashrate issues. May just be a glitch, planning to reset and configure again tomorrow to see if it corrects itself. Just to tired to play with tonight.

A few are actually hashing near/above 700 GHash.

Job well done BitMainTech! I think youve cornered the market!

Strato

What do you have them clocked at to achieve near 700?

They are all at 243.75 but it appears to be actually hashing at 700, showing that rate both miner and poolside.

Weird but very nice.

Strato

[MoreBloodWine]

Ok, so since I formatted my hdd in my laptop like two weeks ago. I lost some of my favorite links.

Can someone post me a ink on the new firmware I have with the stuff to edit so I can get 243.75 added back in. I think it was removed when this (the S3) got reset.

Ty.

Bitmain's site has the firmware:
https://www.bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O0633

I use Cygwin to ssh into them then use vi editor.
U can also download putty to ssh in.

Sorry I should have clarified but the post here that shows where to find the file and what the freqs are that BMT left out.

I need to edit the "new" firmware to add 243.75 etc. and there's a post whos link I lost in the format for that here.

Ty.

[visdude]

Ok, so since I formatted my hdd in my laptop like two weeks ago. I lost some of my favorite links.

Can someone post me a ink on the new firmware I have with the stuff to edit so I can get 243.75 added back in. I think it was removed when this (the S3) got reset.

Ty.

Bitmain's site has the firmware:
https://www.bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O0633

I use Cygwin to ssh into them then use vi editor.
U can also download putty to ssh in.

Sorry I should have clarified but the post here that shows where to find the file and what the freqs are that BMT left out.

I need to edit the "new" firmware to add 243.75 etc. and there's a post whos link I lost in the format for that here.

Ty.

The latest firmware (antMiner_S320140826.bin) already includes frequencies from 100M to 250M...yes, including 243.75M.

[Duce]

hello,
I need a little help. I am putting on my 4.6.0 cgminer antminer S3 version as I'm not too good that I am have explained to me how does have simple version. Thank you in advance.
Sorry for my bad English I'm French  

To upgrade to cgminer 4.6 follow this process.
1. SSH into the S3 and login
2. Issue the following commands sequentially.
  a) cd /usr/bin
  b) mv cgminer cgminer.bak
  c) wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
  d) chmod +x cgminer
  e) reboot

To revert back to the stock cgminer (assuming you followed the above process):
1. SSH into the S3 and login
2. Issue the following commands sequentially.
  a) cd /usr/bin
  b) mv cgminer cgminer.4_6
  c) mv cgminer.bak cgminer
  d) reboot

thank you, but I do not know where to go, would it be possible to put screen step by step

im guessing your on windows, so downloiad putty : http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

start the executable, type in your S3 ip address, and connect..

use the same user and password you would use when going into the web user interface

then type in:

cd /usr/bin
mv cgminer cgminer.bak
wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
chmod +x cgminer
/etc/init.d/cgminer restart
exit

Any reason why I keep getting this:
root@antMiner:/usr/bin# wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
wget: bad address 'ck.kolivas.org'
root@antMiner:/usr/bin#

I have tried this with terminal on a MAC and putty on a windows platform and get the same results.

[TrevorS]

Hi guys,

I've a used early S3 that starts high and settles at ~440GH/s for quite awhile, but eventually dips down to ~430GH/s and even slides into the 420s.  Clock is default 218.75MHz, ASIC display is all "o", HW% is .0013, and Accept/Reject ratio is 639:1.  Looking for ideas as to what could be causing the decline.

Setup is Corsair CX750M supplying all four PCI-E ports via individual minimum length cables, August 7 Bitmain FW flash, 4.6.0 CGminer update, Slush's and Eligius pools with "Failover" management.  It's one of four S3s on a single switch divided between two power circuits (two each) and the other three stay ~441GH/s.

Thoughts?

Appears I've been lost in the shuffle (anything new?)  If someone perhaps has some insight into this, I'd appreciate it!

Thanks!

[bspurloc]

hello,
I need a little help. I am putting on my 4.6.0 cgminer antminer S3 version as I'm not too good that I am have explained to me how does have simple version. Thank you in advance.
Sorry for my bad English I'm French  

To upgrade to cgminer 4.6 follow this process.
1. SSH into the S3 and login
2. Issue the following commands sequentially.
  a) cd /usr/bin
  b) mv cgminer cgminer.bak
  c) wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
  d) chmod +x cgminer
  e) reboot

To revert back to the stock cgminer (assuming you followed the above process):
1. SSH into the S3 and login
2. Issue the following commands sequentially.
  a) cd /usr/bin
  b) mv cgminer cgminer.4_6
  c) mv cgminer.bak cgminer
  d) reboot

thank you, but I do not know where to go, would it be possible to put screen step by step

im guessing your on windows, so downloiad putty : http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html

start the executable, type in your S3 ip address, and connect..

use the same user and password you would use when going into the web user interface

then type in:

cd /usr/bin
mv cgminer cgminer.bak
wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
chmod +x cgminer
/etc/init.d/cgminer restart
exit

Any reason why I keep getting this:
root@antMiner:/usr/bin# wget http://ck.kolivas.org/apps/cgminer/antminer/s3/4.6.0-140908/cgminer
wget: bad address 'ck.kolivas.org'
root@antMiner:/usr/bin#

I have tried this with terminal on a MAC and putty on a windows platform and get the same results.

you are being blocked to ck.kolivas.org or ck.kolivas.org is not resolving
do
nslookup ck.kolivas.org

Name:    reaver.kolivas.org
Address:  193.19.136.183
Aliases:  ck.kolivas.org

and do
ping 193.19.136.183

[bspurloc]

how many times do these need to be cleared by customs?

china
09/18/2014    3:19 P.M.    The clearing agency is experiencing technical difficulties and is temporarily unable to transmit package information. / Your package was released by the clearing agency.

alaska
09/18/2014    10:07 A.M.    The package is awaiting clearing agency review. / The package is at the clearing agency awaiting final release.

EAST COAST now NY?
09/18/2014    11:18 P.M.    The package is awaiting clearing agency review. / Your package was released by the clearing agency.

[MiningBuddy]

how many times do these need to be cleared by customs?

china
09/18/2014    3:19 P.M.    The clearing agency is experiencing technical difficulties and is temporarily unable to transmit package information. / Your package was released by the clearing agency.

alaska
09/18/2014    10:07 A.M.    The package is awaiting clearing agency review. / The package is at the clearing agency awaiting final release.

EAST COAST now NY?
09/18/2014    11:18 P.M.    The package is awaiting clearing agency review. / Your package was released by the clearing agency.

Was about 3 or 4 times for me to the UK

[Duce]

you are being blocked to ck.kolivas.org or ck.kolivas.org is not resolving
do
nslookup ck.kolivas.org

Name:    reaver.kolivas.org
Address:  193.19.136.183
Aliases:  ck.kolivas.org

and do
ping 193.19.136.183

That worked with terminal before I logged into one of the ants but once in the ant I tried again this time it came back with the 127.0.0.0, local bitcoind, not sure why it resolved to this. I can download the file so I guess I will just need to go about this a different way. Thank you for the quick reply.

[davecoin]

Hey all, I was updating my batch 1 S3 units to the latest firmware and one of them is having troubles booting now.  I cannot access it via the webui or via ssh.  I attempted a hard reset using the button on the front so I know the address of the miner should be 192.168.1.99.  Red light is blinking. I'm familiar with how to talk to the miners as I've had around 10 S1, a couple S2, and 10 S3.  This is the only one giving me issues.  

I swapped control boards with another S3 and it's working fine, so the hashing boards are okay.  I sent an email requesting an RMA for the control board.  

Does anybody have anything else I can try?

Thanks,
Dave

Use tcpdump to monitor the traffic on the subnet.  Once I thought I had changed to DHCP and moved the device to another subnet but couldn't find it with nmap.  I ran tcpdump on another machine on that subnet and most of the traffic had the correct subnet but some packets had the .1.99 address so I knew the problem was that it didn't take the protocol change to DHCP.

Why would the address be anything other than 192.168.1.99 though? I did a hard reset.

The hard reset didn't actually work.  I'm able to access the webui now, but neither asic chain shows on the miner status page.  I've tried reverting back to the original firmware and clearing all of my settings. I get usb errors in the log:

Code:

[   27.910000] usb 1-1.1: device not accepting address 4, error -145
[   28.010000] usb 1-1.1: new full-speed USB device number 5 using ehci-platform
[   38.430000] usb 1-1.1: device not accepting address 5, error -145
[   38.530000] usb 1-1.1: new full-speed USB device number 6 using ehci-platform
[   48.950000] usb 1-1.1: device not accepting address 6, error -145
[   48.950000] hub 1-1:1.0: unable to enumerate USB device on port 1

I switched USB cables and have the same issue.  With another control board the miner functions normally.

Tech support is telling me I may have a DNS problem.  I have 8 other ants with the same DNS.  What am I missing here?

[MoreBloodWine]

Ok, so since I formatted my hdd in my laptop like two weeks ago. I lost some of my favorite links.

Can someone post me a ink on the new firmware I have with the stuff to edit so I can get 243.75 added back in. I think it was removed when this (the S3) got reset.

Ty.

Bitmain's site has the firmware:
https://www.bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O0633

I use Cygwin to ssh into them then use vi editor.
U can also download putty to ssh in.

Sorry I should have clarified but the post here that shows where to find the file and what the freqs are that BMT left out.

I need to edit the "new" firmware to add 243.75 etc. and there's a post whos link I lost in the format for that here.

Ty.

The latest firmware (antMiner_S320140826.bin) already includes frequencies from 100M to 250M...yes, including 243.75M.

Please check your facts because it DOES NOT, I've had the FW installed since Day 1 of its release and it doesnt have 243.75 so I revert to my "what I should have said" comment.

philipma knows what I'm asking for if he sees this... Ty.

[TrevorS]

I have six S3 and only two seem to be able to accept a 225 clock.  The others drop GH/s, not increase!