aclass
|
|
October 24, 2014, 10:30:51 PM |
|
Where did HW go? I can't find it in the new firmware
Naaah: Found it below all the pool lines
|
|
|
|
cloh76
|
|
October 24, 2014, 10:37:21 PM |
|
As promised, quicker way to fix config page issue 1)Putty into S3 2)Paste the code in below.. Will replace Save&Apply with Save&Apply. sed -i 's/Save\&Apply/Save\&Apply/g' /usr/lib/lua/luci/model/cbi/cgminer/cgminer.lua Thanks Ustler - Just to clarify... 1) Download the updated firmware from: https://bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O06332) Putty into S3 3) Paste the code in below.. Will replace Save&Apply with Save&Apply. sed -i 's/Save\&Apply/Save\&Apply/g' /usr/lib/lua/luci/model/cbi/cgminer/cgminer.lua 4)Reboot a) cd /usr/bin b) /etc/init.d/cgminer restart Do i need to re-apply or change any settings if flashing an S3+; Is it different from a standard S3?
|
[ BTC Donations: 13RNJdT72WEd1FsT3CwdJ6jy9NAa7Hsb54 ]
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 24, 2014, 10:56:14 PM |
|
To clarify: 1) Download the updated firmware from: https://bitmaintech.com/support.htm?pid=007201407180243004432lBQW28O06332) SSH/Putty into S3 3) Paste the code in below.. Will replace Save&Apply with Save&Apply. sed -i 's/Save\&Apply/Save\&Apply/g' /usr/lib/lua/luci/model/cbi/cgminer/cgminer.lua 4) Execute the following code /etc/init.d/cgminer restart
|
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 24, 2014, 10:58:06 PM |
|
@cloh76
No difference between S3 and S3+.
All settings should be retained during FW upgrade unless you unchecked the "Retain Settings" option.
|
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 24, 2014, 11:01:24 PM |
|
@nst6563
Would love to know if the voltage change works.
|
|
|
|
aclass
|
|
October 24, 2014, 11:18:42 PM |
|
HW still too high... How can I lower those?
|
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 24, 2014, 11:28:02 PM |
|
@aclass
Reduce frequency or possibly change PSU.
How high is too high?
|
|
|
|
toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
October 24, 2014, 11:29:45 PM |
|
HW still too high... How can I lower those?
S3 ? set it to defaults for while see if its a OC issue , is it heating up if so remove the cover for a while to see if open air helps . make sure both fan are turning .I have a upgraded S3 i upgraded that runs better then the S3 i bought from butmain all most no hard ware error with the upgrade .I may just pull the boards on the S3 and re paste them its my Second S3, first one just stopped working they replaced it no questions asked .
|
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 24, 2014, 11:32:45 PM |
|
@toptek
Unless you have fan pointing on S3, removing the cover may do more harm than good. Point of cover is to force air through heatsink fins.
|
|
|
|
toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
October 24, 2014, 11:35:43 PM |
|
This worked great but i like the boot strap skin now that i found it, i may just keep that view.
|
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 24, 2014, 11:40:34 PM |
|
Anyone know if you can get the fans to sync?
Doesn't make sense in a push/pull config to have one fan running at a different speed than the other.
|
|
|
|
toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
October 24, 2014, 11:42:13 PM |
|
@toptek
Unless you have fan pointing on S3, removing the cover may do more harm than good. Point of cover is to force air through heatsink fins.
OK, i removed it once it seemed ok . but then again i also push pull the fans. then why does the upgrade run better in open air over the closed one . well any way some thing he can try to see . so ILL reword it take off the cover and run some fans on the S3 blades .I can give all kinds of advice you can try but the main one lower the OC to start, to see. then go with a new PSU . I won't give much advice on OCing other then don't unless you know what your doing .
|
|
|
|
toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
October 24, 2014, 11:46:13 PM |
|
Anyone know if you can get the fans to sync?
Doesn't make sense in a push/pull config to have one fan running at a different speed than the other.
wish i could figure out how to make both show up with the upgrade and sync them as well .
|
|
|
|
aclass
|
|
October 24, 2014, 11:53:55 PM |
|
@aclass
Reduce frequency or possibly change PSU.
How high is too high?
S3 with latest FW High as in the ballpark of accepted high.(currently 101 HW and 206 Accepted) Not an OC issue as its high at that level as well. Tried to UC with the same result. Temps are at 35 and 39. I'll try with another PSU tomorrow but this one is a 1200W gold with all 4 sockets full on the S3
|
|
|
|
Ustler
Newbie
Offline
Activity: 52
Merit: 0
|
|
October 25, 2014, 12:00:04 AM |
|
@aclass
What is your temps and frequency?
|
|
|
|
toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
October 25, 2014, 12:03:42 AM |
|
@aclass
Reduce frequency or possibly change PSU.
How high is too high?
S3 with latest FW High as in the ballpark of accepted high. Not an OC issue as its high at that level as well. Tried to UC with the same result. Temps are at 35 and 39. I'll try with another PSU tomorrow but this one is a 1200W gold with all 4 sockets full on the S3 try this to it might help mine with http:whatever not with stratum+tcp just to see if that helps any set D=1024 as your pw no x or PW it should let you mine and set /#xnsub after the url port # and /#xnsub seems to work with CGminer now lets me use CGMiner with that in the URL after the port number.
|
|
|
|
aclass
|
|
October 25, 2014, 12:04:19 AM |
|
@aclass
What is your temps and frequency?
temp 35 and 40. Frequency is 237 right now but just for a test. On the default the HW are even more.
|
|
|
|
toptek
Legendary
Offline
Activity: 1274
Merit: 1000
|
|
October 25, 2014, 12:11:28 AM |
|
@aclass
What is your temps and frequency?
temp 35 and 40. Frequency is 237 right now but just for a test. On the default the HW are even more. I had the same issue till i started using http:whatever + this firmware seemed to help a lot i was getting lot of HW error more at defaults then i updated CGminer and the firmware it help a lot, to day lone on the closed cover S3 after the 7 hours at defaults I hit 10 HW errors with no rejects but i all so used some of the above stuff it helped on top of the new update.
|
|
|
|
philipma1957
Legendary
Offline
Activity: 4200
Merit: 8242
'The right to privacy matters'
|
|
October 25, 2014, 12:24:56 AM |
|
@aclass
Reduce frequency or possibly change PSU.
How high is too high?
S3 with latest FW High as in the ballpark of accepted high.(currently 101 HW and 206 Accepted) Not an OC issue as its high at that level as well. Tried to UC with the same result. Temps are at 35 and 39. I'll try with another PSU tomorrow but this one is a 1200W gold with all 4 sockets full on the S3 You wasting time as your description is not adequate please show a screen shot like this. If you can't do a screen shot. list all this info Elapsed : Please wait more then 3 hours GH/s(5s) : GH/S(avg): Accepted: HW: DiffA: DiffR: Frequency: Frequency: Fan: Fan: Temp: Temp: We can then tell if you have a lot of hw . 3 hours min for a reading is needed.
|
|
|
|
aclass
|
|
October 25, 2014, 12:28:00 AM |
|
So you mean something like this: This is before the Firmware update ... Now it's not that different
|
|
|
|
|